Harman Stove Company The Harman Accentra Pellet Insert manual Automatic Ignition/Operation

Page 4

Automatic Ignition/Operation

5

 

 

The Accentra Insert is more than just automatic ignition, it is also automatic temperature control. The automatic system will allow the fire size to be adjusted to match the heating needs and even put the fire out if necessary. If heat is needed after the fire is out, the Accentra Insert will automatically re-ignite and adjust the fire size to match the heating need. The totally automatic roomsensor mode is recommended because of its efficiency. The unit can be switched between "AUTO" and "MANUAL" at any time during operation.

Fig. 3

Room Temperature Mode: This setting will produce a room temperature of 70 degrees with the distribution blower at medium speed.

Stove Temperature Mode

This setting will produce medium heat with the distribution blower on "low".

This setting will produce continuous maximum heat output with the distribution blower at full speed.

Igniter switch to "AUTO"

Room Temperature Mode

In "Room Temp Mode" heat output is controlled au- tomatically by the Room Sensing Probe. When the Room Sensing Probe calls for heat, the stove will increase out- put. When the Room Sensing Probe is getting close to the set temperature, the stove will begin to level off out- put and keep the fire burning at just the right temperature to maintain that setting.

High output is determined by the feed rate set- ting. This setting, generally on #4, can be increased if higher burn rates are necessary (Fig. 1). The unit's maxi- mum burn rate should not create less than 1" of ash on the burn pot front edge(See Fig.2). Overfeeding is not a safety concern, but fuel may be wasted if unburned pel- lets fall into the ash pan.

In "Room Temp Mode" a constant fuel consumption rate is sacrificed for exact room temperature. Therefore, as it gets colder more pellets will be burned automati- cally.

The distribution blower speed will vary according to the position of the mode selector pointer, and fire size.

Igniter switch to "AUTO"

Stove Temperature Mode

This allows for automatic ignition upon start-up only. The unit can then be set at any desired setting. The heat output and fuel consumption will remain constant regard- less of room temperature (See Fig 4). The unit's maxi- mum feed rate should not create less than 1" of ash on the burn pot front edge. See Fig 2.

The unit's low burn or maintenance setting is as low as it will go. It will not go out unless it runs out of fuel or is turned off.

Shut-Down Procedure

To kill the fire or stopburning the stove, turn the Mode Selector to "OFF". This will cause the fire to diminish and burn out. When the fire burns out and the stove cools down everything will stop.

If you pull the plug to shut down the stove, all motors will stop. This may cause incomplete combustion and smoke in the firebox. If the load door is opened the smoke may escape.

The best way to shut down the stove is simply let it run out of pellets, then the stove will shut down automati- cally.

Fig. 4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Installation & Operating Manual Harman Accentra Pellet InsertTable of Contents Introduction3Automatic Start Up Starting First FireStove Temperature Mode Igniter switch to Auto Room Temperature ModeIgniter switch to Auto Stove Temperature Mode Shut-Down ProcedureIgniter Switch toMANUAL down position Manual Start UpManual Stove Temperature Mode Igniter Switch to Manual Room Temperature ModeIgniter Switch to Manual Stove Temperature Mode Manual Ignition/OperationStatus light error messages ESP ControlInstallation Removing unit from skid How to Reduce the Weight for InstallationInstallation10 How to Reduce the Weight for Installation, contdRemoving the Center Medallion Removing the Heat Exchanger CoversInstallation11 SecurelyInstallation12 Installation13 Connecting the room sensor as a return airsensorInstallation14 Flue Pipe Stub AssemblyConnecting the ground from the wing to Stove body Installation15Connecting the power cord Installation16 Connecting the Room SensorDocking Gasket Hopper SealInstallation17 Cast Side Panel InstallationInstallation18 Wiring Log Set OptionLow Draft Voltage Adjustment Draft Meter bolt hole locationMobile Home Installation Mobile Home InstallationSafety Reminders Venting21 PL Vent PipeOutside Air Venting22Vent Pipe #1 Installing into an existing fireplace Chimney US & Canada Venting23Venting24 #3 Installing into an existing Chimney US only#4 Preferred method Venting25 Accentra Insert Zero Clearance Cabinet Harman Mantel SystemWith outside air installed, 6 feet With outside air installedVenting27 Maintenance Cleaning Glass on View Door Maintenance Burn Pot Burn Pot Cleaning and MaintenanceCleaning the Heat Exchanger tubes Maintenance Cleaning30Cleaning the Heat Exchanger To remove the feeder cover Maintenance Cleaning31To remove the combustion blower Backdraft Damper Assembly Accentra Insert Motor & Component LocationsTrouble-Shooting33 Cleaning Burn PotHelpful Hints FuelSpecifications34 Accentra Insert Wiring Diagram Accentra Insert Feeder Parts Accentra Insert Parts List Harman Gold Warranty Harman Gold Warranty

The Harman Accentra Pellet Insert specifications

The Harman Stove Company is renowned for its high-quality heating solutions, and the Harman Accentra Pellet Insert exemplifies their commitment to efficiency and performance. Designed to seamlessly blend into existing fireplace openings, the Accentra Pellet Insert offers homeowners a reliable source of warmth while enhancing the aesthetics of their living space.

One of the standout features of the Accentra is its advanced pellet-burning technology. This insert utilizes a powerful feed system that ensures a consistent and controllable burn rate, leading to a more efficient heating experience. The patented Smart Control technology enables users to monitor and adjust the temperature easily, ensuring that every room is kept at the perfect temperature with minimal effort.

The Accentra Pellet Insert also comes equipped with a user-friendly interface, making it accessible even for those unfamiliar with pellet stoves. Its LCD screen displays vital information, including temperature settings and fuel levels, allowing users to make informed adjustments. This level of convenience is complemented by the unit's automatic ignition feature, which simplifies startup, eliminating the need for matches or manual lighting.

In terms of efficiency, the Harman Accentra boasts an impressive high-efficiency rating. With a heating capacity of up to 2,200 square feet, it provides substantial warmth, making it an ideal choice for larger homes or open spaces. The insert’s environmentally-friendly design minimizes emissions, contributing to cleaner air and promoting sustainable heating practices.

The construction of the Accentra Pellet Insert is equally impressive. Built with durable materials, it is designed for longevity and dependability. The insert's sleek and contemporary design fits neatly into a variety of home decors, allowing homeowners to enjoy a cozy fire without sacrificing style.

Another key characteristic of the Accentra Pellet Insert is its versatility in fuel options. Users can choose from various brands of pellets, optimizing fuel choices based on availability and pricing. With a large capacity hopper, the Accentra can hold ample pellets, reducing the frequency of refueling and allowing for extended burn times.

In summary, the Harman Accentra Pellet Insert embodies the company's dedication to quality and innovation. With its efficient heating capabilities, advanced technology, user-centric design, and adaptability, it stands out as a premium choice for anyone looking to enhance their home’s heating system while enjoying the comforting glow of a real fire. Investing in the Harman Accentra is not just a choice for warmth; it's a commitment to quality, aesthetics, and sustainable living.
Top Page Image Contents