Harman Stove Company The Harman Accentra Pellet Insert manual Installation11, Securely

Page 10

Installation11

Beginning Installation

IMPORTANT: The mounting frame/surround

 

assembly and flue piping is the most critical part of

 

the installation andmust be done correctly and installed

Notch

securely.

 

1. Choose the chimney configuration that is best suited

 

for the installation. See venting section.

 

• Note: If 100% outside air is desired or required, the

 

outside air option will need to be installed on the stoves

 

body. (See instructions included with outside air kit

 

(part #1-00-674080.) See Page 20.

 

2. Make sure the unit will fit into the fireplace opening.

 

See Fig # 17. When installing in smaller fireplaces,

 

test fit the mounting frame into the firebox. Note: The

 

unit overhangs to the rear.

 

3" Outside Air starter collar

3.Install the 3 piece cast surround set to the sides and top of the mounting frame with the bolts and nuts supplied. The left and right side should be done before the center section is installed. Make sure the bolts are loose. Do not remove the side panel hinges. The left and right side wings should be standing up aligned with the side of the mounting frame and slid inward towards the center. Note:The wings mount on the rear side below the notch and on the front side above the notch. See Fig. 16 & 18. Slide the cast ash lip onto the frame and check to make sure it can go against the roped frame rails and fits into the pockets on the left and right cast sides. See Fig. 19.

Install the center section.

4.If the wing extensions are required they should be installed next.

Cast in front of the frame. Use (1)1/4-20 x 3/8 flange bolt from the rear.

Fig. 16

Ash lip slide rails

Fig. 17

Approximately 2" overhang

NOTE: The stove body extends through the mounting frame in the rear approximately 2".

Cast behind the mounting frame flange. Use (2) 1 / 4 - 2 0 x 5 / 8 flange bolts and nuts with bolts fromthe front.

Fig. 18

Slide the ash lip

 

casting into the

 

frame,

making

 

certain the ash lip

 

is sitting on the

 

slide

rails

on

 

either side. With

 

the ash

lip

in

 

place, adjust the

 

surround sides so

 

there is an even

 

gap where the ash

 

lip extends into

the

surround

side

and

tighten.

 

 

 

Fig. 19

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation & Operating Manual Harman Accentra Pellet InsertTable of Contents Introduction3Automatic Start Up Starting First FireIgniter switch to Auto Stove Temperature Mode Stove Temperature ModeIgniter switch to Auto Room Temperature Mode Shut-Down ProcedureIgniter Switch toMANUAL down position Manual Start UpIgniter Switch to Manual Stove Temperature Mode Manual Stove Temperature ModeIgniter Switch to Manual Room Temperature Mode Manual Ignition/OperationStatus light error messages ESP ControlInstallation Removing unit from skid How to Reduce the Weight for InstallationRemoving the Center Medallion Installation10How to Reduce the Weight for Installation, contd Removing the Heat Exchanger CoversInstallation11 SecurelyInstallation12 Installation13 Connecting the room sensor as a return airsensorInstallation14 Flue Pipe Stub AssemblyConnecting the ground from the wing to Stove body Installation15Connecting the power cord Docking Gasket Installation16Connecting the Room Sensor Hopper SealInstallation17 Cast Side Panel InstallationInstallation18 Wiring Log Set OptionLow Draft Voltage Adjustment Draft Meter bolt hole locationMobile Home Installation Mobile Home InstallationSafety Reminders Venting21 PL Vent PipeOutside Air Venting22Vent Pipe #1 Installing into an existing fireplace Chimney US & Canada Venting23Venting24 #3 Installing into an existing Chimney US only#4 Preferred method Venting25 Accentra Insert Zero Clearance Cabinet Harman Mantel SystemWith outside air installed, 6 feet With outside air installedVenting27 Maintenance Cleaning Glass on View Door Maintenance Burn Pot Burn Pot Cleaning and MaintenanceCleaning the Heat Exchanger tubes Maintenance Cleaning30Cleaning the Heat Exchanger To remove the feeder cover Maintenance Cleaning31To remove the combustion blower Backdraft Damper Assembly Accentra Insert Motor & Component LocationsHelpful Hints Trouble-Shooting33Cleaning Burn Pot FuelSpecifications34 Accentra Insert Wiring Diagram Accentra Insert Feeder Parts Accentra Insert Parts List Harman Gold Warranty Harman Gold Warranty

The Harman Accentra Pellet Insert specifications

The Harman Stove Company is renowned for its high-quality heating solutions, and the Harman Accentra Pellet Insert exemplifies their commitment to efficiency and performance. Designed to seamlessly blend into existing fireplace openings, the Accentra Pellet Insert offers homeowners a reliable source of warmth while enhancing the aesthetics of their living space.

One of the standout features of the Accentra is its advanced pellet-burning technology. This insert utilizes a powerful feed system that ensures a consistent and controllable burn rate, leading to a more efficient heating experience. The patented Smart Control technology enables users to monitor and adjust the temperature easily, ensuring that every room is kept at the perfect temperature with minimal effort.

The Accentra Pellet Insert also comes equipped with a user-friendly interface, making it accessible even for those unfamiliar with pellet stoves. Its LCD screen displays vital information, including temperature settings and fuel levels, allowing users to make informed adjustments. This level of convenience is complemented by the unit's automatic ignition feature, which simplifies startup, eliminating the need for matches or manual lighting.

In terms of efficiency, the Harman Accentra boasts an impressive high-efficiency rating. With a heating capacity of up to 2,200 square feet, it provides substantial warmth, making it an ideal choice for larger homes or open spaces. The insert’s environmentally-friendly design minimizes emissions, contributing to cleaner air and promoting sustainable heating practices.

The construction of the Accentra Pellet Insert is equally impressive. Built with durable materials, it is designed for longevity and dependability. The insert's sleek and contemporary design fits neatly into a variety of home decors, allowing homeowners to enjoy a cozy fire without sacrificing style.

Another key characteristic of the Accentra Pellet Insert is its versatility in fuel options. Users can choose from various brands of pellets, optimizing fuel choices based on availability and pricing. With a large capacity hopper, the Accentra can hold ample pellets, reducing the frequency of refueling and allowing for extended burn times.

In summary, the Harman Accentra Pellet Insert embodies the company's dedication to quality and innovation. With its efficient heating capabilities, advanced technology, user-centric design, and adaptability, it stands out as a premium choice for anyone looking to enhance their home’s heating system while enjoying the comforting glow of a real fire. Investing in the Harman Accentra is not just a choice for warmth; it's a commitment to quality, aesthetics, and sustainable living.
Top Page Image Contents