Harman Stove Company The Harman Accentra Pellet Insert manual Installation17

Page 16

Installation17

22.Slide the stove body into the mounting frame.

• Note: The two spring latches on the bottom

right and left side of the body must be in the proper

position to enter the latch holes. (See fig. 37).

• Latch the (2) spring latches into place.

23.Shift the cast top/hopper lid assembly inward as far as possible to achieve a parallel fit with the surround sides. See Fig. 39. Tighten the cast top/hopper lid assembly bolts with a 3/8" socket. See page 8, Fig. 12.

24.Install and adjust the side panel magnets.

•In the hardware pack are (2) magnets, (2) spacers and

(2) 10-32 x 1 1/4" bolts and nuts.

•Bolt the magnets through the cast iron hole provided. Important: The spacer must be on top of the hole, the magnet on top of the spacer with the bolt going down through the hole with the nut at the bottom, under the ash lip. See fig. 38.

25.Check the fit of the cast ash lip to make sure that it can be slid in and out easily. The cast ash lip can remain in place at this time. Note: The cast side panel hinges can be moved upward if necessary to gain clearance for the cast ash lip.

Latch Hole

Spring Latch

Magnet

Fig. 37

Magnet

Fig. 38

Cast Side Panel Installation

•The stove body must be pulled out of the mounting frame several inches to install the cast side panels.

•Slide the cast side panel down over the hinge pins.

•Slide the stove body in and latch into place.

•Note: The cast side panels must be left in the open position to allow access to the latches.

•Slide the ash lip into place. (This would be inward until the rear of the cast iron touches the mounting frame front.)

•Close the cast side panels.

•Check the gap alignment and the top and bottom gap spacing.

•The top and bottom spacing can be adjusted by loos- ening the 3 bolts and sliding the hinge up or down until the spacing suits.

•With the front door closed and latched, check the vertical space alignment. The only method of chang- ing or adjusting this gap is by bending (slightly) the hinge angle. See fig. 39.

•Due to the use of all cast iron parts, some small amounts of misalignment are expected. Since some parts are angled and some have rounded edges, this misalignment is very seldom noticable.

•It is very important that the cast side panels open and close freely for good control board access.

Fititcastt

top/t /

hopperr

lidlid

parallelparallel

withith

surroundrr ..

Side panel gap

Fig. 39

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Installation & Operating Manual Harman Accentra Pellet InsertTable of Contents Introduction3Automatic Start Up Starting First FireStove Temperature Mode Igniter switch to Auto Room Temperature ModeIgniter switch to Auto Stove Temperature Mode Shut-Down ProcedureIgniter Switch toMANUAL down position Manual Start UpManual Stove Temperature Mode Igniter Switch to Manual Room Temperature ModeIgniter Switch to Manual Stove Temperature Mode Manual Ignition/OperationStatus light error messages ESP ControlInstallation Removing unit from skid How to Reduce the Weight for InstallationInstallation10 How to Reduce the Weight for Installation, contdRemoving the Center Medallion Removing the Heat Exchanger CoversInstallation11 SecurelyInstallation12 Installation13 Connecting the room sensor as a return airsensorInstallation14 Flue Pipe Stub AssemblyConnecting the ground from the wing to Stove body Installation15Connecting the power cord Installation16 Connecting the Room SensorDocking Gasket Hopper SealInstallation17 Cast Side Panel InstallationInstallation18 Wiring Log Set OptionLow Draft Voltage Adjustment Draft Meter bolt hole locationMobile Home Installation Mobile Home InstallationSafety Reminders Venting21 PL Vent PipeOutside Air Venting22Vent Pipe #1 Installing into an existing fireplace Chimney US & Canada Venting23Venting24 #3 Installing into an existing Chimney US only#4 Preferred method Venting25 Accentra Insert Zero Clearance Cabinet Harman Mantel SystemWith outside air installed, 6 feet With outside air installedVenting27 Maintenance Cleaning Glass on View Door Maintenance Burn Pot Burn Pot Cleaning and MaintenanceCleaning the Heat Exchanger tubes Maintenance Cleaning30Cleaning the Heat Exchanger To remove the feeder cover Maintenance Cleaning31To remove the combustion blower Backdraft Damper Assembly Accentra Insert Motor & Component LocationsTrouble-Shooting33 Cleaning Burn PotHelpful Hints FuelSpecifications34 Accentra Insert Wiring Diagram Accentra Insert Feeder Parts Accentra Insert Parts List Harman Gold Warranty Harman Gold Warranty

The Harman Accentra Pellet Insert specifications

The Harman Stove Company is renowned for its high-quality heating solutions, and the Harman Accentra Pellet Insert exemplifies their commitment to efficiency and performance. Designed to seamlessly blend into existing fireplace openings, the Accentra Pellet Insert offers homeowners a reliable source of warmth while enhancing the aesthetics of their living space.

One of the standout features of the Accentra is its advanced pellet-burning technology. This insert utilizes a powerful feed system that ensures a consistent and controllable burn rate, leading to a more efficient heating experience. The patented Smart Control technology enables users to monitor and adjust the temperature easily, ensuring that every room is kept at the perfect temperature with minimal effort.

The Accentra Pellet Insert also comes equipped with a user-friendly interface, making it accessible even for those unfamiliar with pellet stoves. Its LCD screen displays vital information, including temperature settings and fuel levels, allowing users to make informed adjustments. This level of convenience is complemented by the unit's automatic ignition feature, which simplifies startup, eliminating the need for matches or manual lighting.

In terms of efficiency, the Harman Accentra boasts an impressive high-efficiency rating. With a heating capacity of up to 2,200 square feet, it provides substantial warmth, making it an ideal choice for larger homes or open spaces. The insert’s environmentally-friendly design minimizes emissions, contributing to cleaner air and promoting sustainable heating practices.

The construction of the Accentra Pellet Insert is equally impressive. Built with durable materials, it is designed for longevity and dependability. The insert's sleek and contemporary design fits neatly into a variety of home decors, allowing homeowners to enjoy a cozy fire without sacrificing style.

Another key characteristic of the Accentra Pellet Insert is its versatility in fuel options. Users can choose from various brands of pellets, optimizing fuel choices based on availability and pricing. With a large capacity hopper, the Accentra can hold ample pellets, reducing the frequency of refueling and allowing for extended burn times.

In summary, the Harman Accentra Pellet Insert embodies the company's dedication to quality and innovation. With its efficient heating capabilities, advanced technology, user-centric design, and adaptability, it stands out as a premium choice for anyone looking to enhance their home’s heating system while enjoying the comforting glow of a real fire. Investing in the Harman Accentra is not just a choice for warmth; it's a commitment to quality, aesthetics, and sustainable living.
Top Page Image Contents