Harman Stove Company The Harman Accentra Pellet Insert Installation14, Flue Pipe Stub Assembly

Page 13

Installation14

9.Install the completed frame/surround assembly into the firebox and level/plumb the wing to the fireplace face using the leveling bolts as jacks.

* Ash protection must be used from hearth opening to 6" in front of door glass and 6" to each side of the stove body to protect any combustibles from hot ashes. A minimum size will be 16.5" deep by 30" wide and be made of a non- combustible material or meet UL approval.

Fig. 28

(from glass)

10.Test fit the cast ash lip (See fig. 25) on the shell frame mounting rails. The ash lip should slide on these side rails without lifting upward off of the rails as the ash lip is slid inward. A small clearance of about 1/16" is an ideal space between the legs of the ash lip and the hearth. This cast ash lip is a decorative part that does not and should not support any weight.

11.Tighten the (2) 1/2" threaded wedging rods up against the lintel of the fireplace opening. It is also recommended to use some form of anchoring screws through the bottom of the shell into the hearth. There are up to 5 holes provided. Note: It is a good idea to check the ash lip again. The frame may have shifted when the final anchoring was completed. See fig. 26.

12.Complete the flue piping, and outside air piping, if used. Make sure the damper area is sealed.

CAUTION: IF THE STAINLESS STEEL FLUE PIPE DOES NOT EXTEND FAR ENOUGH ABOVE THE OLD DAMPER OPENING, MAKE SURE THE FIBERGLASS INSULATION DOES NOT EXTEND UPWARD AND COVER THE PIPE OUTLET.

WARNING DO NOT CONNECT THIS UNIT TO ANY AIR DIS- TRIBUTION DUCT OR SYSTEM.

13.If a rear exit flue configuration is used, with or without outside air, make sure the flue pipe termination clearances are followed as per the manufacturers recommendations.

16.Place the stove body on the mounting shell gasketed rails and insert the body into the opening far enough that it can't tip out. Note: A service rail kit (part # 1-00-08007), or a pair of 2x4's supported in front of the hearth will make this job easier.' See Fig. 31.

Ash lip

17.Complete the following electrical connections (Caution: mounting

Disconnect the power cord.) There are 5 connections that rails

must be completed. See Fig. 33 & 34.

Fig. 27

Pre-cut ceramic insulation and (2) pieces of tie wire.

Flue Pipe Stub Assembly

There are three different diameter flue pipe stub assemblys.

1. The unit comes standard with the largest for use with 4”

stainless steel flex pipe.

2.Part #1-10-082745 for use with 4” PL vent starter pipe.

3.Part # 1-10-674039 for use with 3” PL vent starter pipe and also for use with 3” aluminum flex duct for out- side air connections.

The flue stub assembly base is a round plate which al- lows it to swivel to allow the flue pipe to exit the mount- ing frame in other positions rather than straight up. See fig. 28.

14.Install the flue pipe insulation wrap. See Fig. 27. This ceramic insulation is precut to form around the flue pipe stub, to reduce heat transfer into the area around the rear of the hopper and motor area. This insulation must be installed in all configurations, even if a rear discharge is used. See Fig. 29.

This picture shows the completed

insulation wrapped around the flue pipe

Twisted tie wire

from the mounting frame upward.

Fig. 29

With larger flue pipes this bottom edge of the insulation will need to be trimmed to complete the wrap.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Harman Accentra Pellet Insert Installation & Operating ManualIntroduction3 Table of ContentsStarting First Fire Automatic Start UpIgniter switch to Auto Room Temperature Mode Stove Temperature ModeIgniter switch to Auto Stove Temperature Mode Shut-Down ProcedureManual Start Up Igniter Switch toMANUAL down positionIgniter Switch to Manual Room Temperature Mode Manual Stove Temperature ModeIgniter Switch to Manual Stove Temperature Mode Manual Ignition/OperationESP Control Status light error messagesHow to Reduce the Weight for Installation Installation Removing unit from skidHow to Reduce the Weight for Installation, contd Installation10Removing the Center Medallion Removing the Heat Exchanger CoversSecurely Installation11Installation12 Connecting the room sensor as a return airsensor Installation13Flue Pipe Stub Assembly Installation14Connecting the ground from the wing to Stove body Installation15Connecting the power cord Connecting the Room Sensor Installation16Docking Gasket Hopper SealCast Side Panel Installation Installation17Wiring Log Set Option Installation18Draft Meter bolt hole location Low Draft Voltage AdjustmentMobile Home Installation Mobile Home InstallationSafety Reminders PL Vent Pipe Venting21Outside Air Venting22Vent Pipe Venting23 #1 Installing into an existing fireplace Chimney US & CanadaVenting24 #3 Installing into an existing Chimney US only#4 Preferred method Venting25 Harman Mantel System Accentra Insert Zero Clearance CabinetWith outside air installed, 6 feet With outside air installedVenting27 Maintenance Cleaning Glass on View Door Burn Pot Cleaning and Maintenance Maintenance Burn PotCleaning the Heat Exchanger tubes Maintenance Cleaning30Cleaning the Heat Exchanger To remove the feeder cover Maintenance Cleaning31To remove the combustion blower Accentra Insert Motor & Component Locations Backdraft Damper AssemblyCleaning Burn Pot Trouble-Shooting33Helpful Hints FuelSpecifications34 Accentra Insert Wiring Diagram Accentra Insert Feeder Parts Accentra Insert Parts List Harman Gold Warranty Harman Gold Warranty

The Harman Accentra Pellet Insert specifications

The Harman Stove Company is renowned for its high-quality heating solutions, and the Harman Accentra Pellet Insert exemplifies their commitment to efficiency and performance. Designed to seamlessly blend into existing fireplace openings, the Accentra Pellet Insert offers homeowners a reliable source of warmth while enhancing the aesthetics of their living space.

One of the standout features of the Accentra is its advanced pellet-burning technology. This insert utilizes a powerful feed system that ensures a consistent and controllable burn rate, leading to a more efficient heating experience. The patented Smart Control technology enables users to monitor and adjust the temperature easily, ensuring that every room is kept at the perfect temperature with minimal effort.

The Accentra Pellet Insert also comes equipped with a user-friendly interface, making it accessible even for those unfamiliar with pellet stoves. Its LCD screen displays vital information, including temperature settings and fuel levels, allowing users to make informed adjustments. This level of convenience is complemented by the unit's automatic ignition feature, which simplifies startup, eliminating the need for matches or manual lighting.

In terms of efficiency, the Harman Accentra boasts an impressive high-efficiency rating. With a heating capacity of up to 2,200 square feet, it provides substantial warmth, making it an ideal choice for larger homes or open spaces. The insert’s environmentally-friendly design minimizes emissions, contributing to cleaner air and promoting sustainable heating practices.

The construction of the Accentra Pellet Insert is equally impressive. Built with durable materials, it is designed for longevity and dependability. The insert's sleek and contemporary design fits neatly into a variety of home decors, allowing homeowners to enjoy a cozy fire without sacrificing style.

Another key characteristic of the Accentra Pellet Insert is its versatility in fuel options. Users can choose from various brands of pellets, optimizing fuel choices based on availability and pricing. With a large capacity hopper, the Accentra can hold ample pellets, reducing the frequency of refueling and allowing for extended burn times.

In summary, the Harman Accentra Pellet Insert embodies the company's dedication to quality and innovation. With its efficient heating capabilities, advanced technology, user-centric design, and adaptability, it stands out as a premium choice for anyone looking to enhance their home’s heating system while enjoying the comforting glow of a real fire. Investing in the Harman Accentra is not just a choice for warmth; it's a commitment to quality, aesthetics, and sustainable living.
Top Page Image Contents