GE 60-875 System Access Alarm, Testing Sensors, To perform the sensor test, Device Do This

Page 28

System Access Alarm

The panel cover was opened while the system was armed. The system will call the cen- tral monitoring station to report a tamper alarm.

Clearing System Status

Press the SYSTEM STATUS button, listen to the status message, then disarm the system to clear system status. If the trouble condition was a low CPU battery, per- form a sensor test. The SYSTEM STATUS button should turn off if all trouble condi- tions have been corrected.

Testing

Note

The RF Electronic Thermo- stat is automatically tested when a sensor test begins. The panel will announce, Sensor XXX activated, sta- tus is one, if the thermostat is OK.

As an added safeguard, there are system tests you should do yourself on a regular basis. It is recommended that you test your system weekly.

Testing Sensors

You can test sensors one at a time to make sure they are sending strong signals to the panel. You should test the security system at least once a week.

￿To perform the sensor test:

1.Open the panel Cover.

2.Enter the master access code.

3.Press the Test button once. The panel will announce Sensor Test.

4.Press the DONE button.

The panel will voice prompt you with a list of your programmed sensors that you need to test. The panel will start with sensor 1 and announce Test sensor 1, sensor name.

When you trip a sensor and it communicates successfully it will be removed from the list. You may trip the sensors in any order. The sensor test has a 4 minute time-out that resets with each sensor trip.

After all sensors have been successfully tested, the panel will announce Sensor test complete, press DONE. Press DONE. The panel will announce Sensor test ok.

If any of the sensors did not test successfully and you want to terminate the test, press DONE or Cancel. The panel will announce Sensor test canceled or failure. If a sensor test fails, call your security dealer.

Use the following table to trip devices:

Device

Do This

 

 

Door/Window Sensor

Open the secured door or window.

 

 

Freeze Sensor

Apply ice to the sensor. Do not allow the sensor to get

 

wet.

 

 

Water Sensor

Press a wet rag or wet finger over both of the round,

 

gold-plated terminals on the underside of the sensor.

 

 

Carbon Monoxide Sensor

Unplug the CO Alarm. Plug it back in, then press the

 

TEST/RESET button until the unit beeps 8 times.

 

 

Glass Guard Sensor

Tap the glass 3 or 4 inches from the sensor.

 

 

Motion Sensor

Avoid the Motion Sensor’s view for 5 minutes, then

 

enter its view.

 

 

Rate-of-Rise Heat Detec-

Rub your hands together until warm, then place one

tor

hand on the detector for 30 seconds.

 

 

23

Simon Security System

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Simon Security System FCC Notices FCC Part 15 Information to the UserCanada Notice Contents Testing Introduction to Your Security System Security System ComponentsHow You Communicate to Your System How to Use Your Control Panel Latchkey Quick ExitSubdisarm Disarming Your System Subdisarm Your SystemChime Doors Chime Special MotionDirect Bypassing Direct UnbypassingHow Your SystemCommunicates To YouAlarm Sirens and Lamp Modules Alarm Siren and X10 Light InformationStatus Beeps Status BeepsCanceling Preventing Accidental Alarms Panel Indicator LightsCanceling Accidental Alarms Numeric PagerHow to Use an Off-Site Phone Guidelines for Preventing Accidental AlarmsHow to gain access to the Control Panel Phone CommandsHow to Use Your TouchpadsARM Doors & Windows ARM Motion SensorsRF Thermostat Operation Programming Your SystemProgramming Instructions Lock and UnlockAccess Codes Enter the Master Access CodeHow to change an Access Code How to Delete an Access CodeLight Control House CodeHow to set time for light control ProgrammingOptions Unit NumberOption 02 Panel Voice Option 01 Status BeepsOption 03 Latchkey Time Option 36 Sensor Activated Light Lockout Start Time Option 37 Sensor Activated Light Lockout Stop TimeOption 41 Voice Chime Option 42 Speaker LevelOption 43 Pager Phone Number Panel will call the pager to indicate the followingOption 55 Status Sounds Option 81 Heating Set PointTrouble Beeps AC Power FailureOption 82 Cooling Set Point System Battery Failure Sensor Low BatterySensor Failure Fail-To-CommunicateTesting System Access AlarmTesting Sensors To perform the sensor testAlarm System Testing CommunicationSetting the Clock LimitationsPlanning for Emergencies ServiceEmergency Planning Your Floor Plan Simon Security System Simon Security System Simon Security System Access Codes Delay Times Sensor LocationsX10 Module Locations Sensor Number Sensor Type LocationControl Panel KeychainTouchpad Control Panel Touchpad Phone

60-875 specifications

The GE 60-875 is a powerful and versatile locomotive known for its robust construction and advanced technology tailored for freight transport. This locomotive is part of the General Electric's Evolution Series, which is designed to enhance efficiency, reduce emissions, and improve the overall performance of freight operations.

One of the main features of the GE 60-875 is its powerful engine, which produces an impressive output of 4,400 horsepower. This strong propulsion allows the locomotive to pull heavy freight trains across diverse terrains, making it a popular choice for freight companies looking to enhance their operational capacities. The locomotive is equipped with a 4-stroke, 16-cylinder engine, combining both power and efficiency in its design.

In terms of technology, the GE 60-875 is equipped with advanced computer systems that enable real-time monitoring of various operational parameters. This data-driven approach helps in optimizing performance and ensuring timely maintenance, thus reducing downtime. Additionally, the locomotive utilizes an automated throttle and brake control system, which enhances the driving experience and ensures seamless operation during transportation.

The GE 60-875 incorporates state-of-the-art emissions control technology, compliant with stringent regulatory standards. The use of selective catalytic reduction (SCR) technology significantly lowers nitrogen oxide emissions, contributing to a cleaner environment. This commitment to sustainability is a key aspect of its design, reflecting the industry's shift towards greener technologies.

Another notable characteristic of the GE 60-875 is the spacious and ergonomic cab design, which enhances the comfort of the crew during long journeys. The cab is equipped with modern controls and displays, allowing the engineer to monitor locomotive systems efficiently. With a focus on safety, the locomotive is designed with enhanced visibility and safety features that provide comprehensive operational oversight.

In summary, the GE 60-875 is a significant player in the freight locomotive market, combining power, efficiency, and advanced technology. With its high horsepower, emissions control features, and user-friendly cabin design, it stands out as a reliable choice for railway operators dedicated to performance and sustainability. This locomotive exemplifies GE's commitment to innovation in the rail industry, ensuring that it remains a top contender in the ever-evolving landscape of freight transport.
Top Page Image Contents