GE 60-875 manual How You Communicate to Your System

Page 7

Outdoor Motion Sensors detect motion in a protected outdoor area. When motion is detected, the system may respond by sounding chimes or turning on outside lights. These sensors are not used for intrusion detection.

Door/Window Sensors detect the opening of a door or window.

Smoke Sensors detect smoke and a significant rise in temperature. They have a built in siren that sounds when smoke or a significant rise in temperature is detected.

Freeze Sensors detect furnace failure. If the inside temperature drops below 41°F, the sensor will notify the panel. The sensor will send a restore signal to the panel when the temperature rises to 50°F.

Carbon Monoxide Sensors detect carbon monoxide. They have a built in siren that sounds when carbon monoxide is detected.

Modules

*Appliance Modules can be programmed to turn appliances or fluorescent lights on and off.

*Lamp Modules can be programmed to turn non-fluorescent lights on and off.

*Universal Modules are primarily used for controlling devices other than appliances and lamps. Check with your installer for other applications.

Audio Verification Module (AVM) is primarily used by the central monitoring sta- tion to monitor sounds and verbally communicate with a person inside the home. This feature is similar to a speaker phone feature on a phone.

*Dialog RF Electronic Thermostat is primarily used to monitor and control HVAC systems from the security system.

*Not investigated for use by UL

How You Communicate to Your System

Note

The Master Access Code default is 1-2-3-4 when the security system is shipped from the factory. You should change your code after your system is installed (see “Programming Your Sys- tem”).

Sending commands or instructing your security system is done through key presses on the panel, touchpads, or through the use of a remote telephone.

Control Panel

You can enter commands for your security system through simple key presses on the panel. Depending on how your system is programmed, you may need to enter an access code for certain commands. An access code is a numeric code that allows authorization to operate your security system.

Remote Handheld Touchpad

This touchpad gives you the option to enter commands from any room in your house. You can enter commands through simple key presses on the touchpad.

Dialog Touchtalk 2-Way RF Touchpad

This touchpad gives you the option to enter commands from a remote location (away from the control panel) in your house. It also allows you to hear panel messages when the System Status button is pressed.

Keychain Touchpad

Keychain Touchpads are handy for simple arming, disarming and light control func- tions. They are portable and can be carried off-site in a purse or pocket

Telephone

Touchtone telephones can be used to communicate with your system while you are off-site. Ask your installer if you have this feature.

Simon Security System

2

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Simon Security System FCC Part 15 Information to the User FCC NoticesCanada Notice Contents Testing Security System Components Introduction to Your Security SystemHow You Communicate to Your System How to Use Your Control Panel Latchkey Quick ExitSubdisarm Subdisarm Your System Disarming Your SystemDirect Unbypassing Chime DoorsChime Special Motion Direct BypassingTo You How YourSystem CommunicatesStatus Beeps Alarm Sirens and Lamp ModulesAlarm Siren and X10 Light Information Status BeepsNumeric Pager Canceling Preventing Accidental AlarmsPanel Indicator Lights Canceling Accidental AlarmsPhone Commands How to Use an Off-Site PhoneGuidelines for Preventing Accidental Alarms How to gain access to the Control PanelARM Motion Sensors How to Use YourTouchpads ARM Doors & WindowsLock and Unlock RF Thermostat OperationProgramming Your System Programming InstructionsEnter the Master Access Code Access CodesHouse Code How to change an Access CodeHow to Delete an Access Code Light ControlUnit Number How to set time for light controlProgramming OptionsOption 02 Panel Voice Option 01 Status BeepsOption 03 Latchkey Time Option 37 Sensor Activated Light Lockout Stop Time Option 36 Sensor Activated Light Lockout Start TimeOption 42 Speaker Level Option 41 Voice ChimePanel will call the pager to indicate the following Option 43 Pager Phone NumberOption 81 Heating Set Point Option 55 Status SoundsTrouble Beeps AC Power FailureOption 82 Cooling Set Point Fail-To-Communicate System Battery FailureSensor Low Battery Sensor FailureTo perform the sensor test TestingSystem Access Alarm Testing SensorsLimitations Alarm SystemTesting Communication Setting the ClockPlanning for Emergencies ServiceEmergency Planning Your Floor Plan Simon Security System Simon Security System Simon Security System Sensor Number Sensor Type Location Access Codes Delay TimesSensor Locations X10 Module LocationsControl Panel Touchpad Phone Control PanelKeychain Touchpad

60-875 specifications

The GE 60-875 is a powerful and versatile locomotive known for its robust construction and advanced technology tailored for freight transport. This locomotive is part of the General Electric's Evolution Series, which is designed to enhance efficiency, reduce emissions, and improve the overall performance of freight operations.

One of the main features of the GE 60-875 is its powerful engine, which produces an impressive output of 4,400 horsepower. This strong propulsion allows the locomotive to pull heavy freight trains across diverse terrains, making it a popular choice for freight companies looking to enhance their operational capacities. The locomotive is equipped with a 4-stroke, 16-cylinder engine, combining both power and efficiency in its design.

In terms of technology, the GE 60-875 is equipped with advanced computer systems that enable real-time monitoring of various operational parameters. This data-driven approach helps in optimizing performance and ensuring timely maintenance, thus reducing downtime. Additionally, the locomotive utilizes an automated throttle and brake control system, which enhances the driving experience and ensures seamless operation during transportation.

The GE 60-875 incorporates state-of-the-art emissions control technology, compliant with stringent regulatory standards. The use of selective catalytic reduction (SCR) technology significantly lowers nitrogen oxide emissions, contributing to a cleaner environment. This commitment to sustainability is a key aspect of its design, reflecting the industry's shift towards greener technologies.

Another notable characteristic of the GE 60-875 is the spacious and ergonomic cab design, which enhances the comfort of the crew during long journeys. The cab is equipped with modern controls and displays, allowing the engineer to monitor locomotive systems efficiently. With a focus on safety, the locomotive is designed with enhanced visibility and safety features that provide comprehensive operational oversight.

In summary, the GE 60-875 is a significant player in the freight locomotive market, combining power, efficiency, and advanced technology. With its high horsepower, emissions control features, and user-friendly cabin design, it stands out as a reliable choice for railway operators dedicated to performance and sustainability. This locomotive exemplifies GE's commitment to innovation in the rail industry, ensuring that it remains a top contender in the ever-evolving landscape of freight transport.
Top Page Image Contents