Lennox Hearth 32FS operation manual Standard Horizontal Vent Installation, Back, Stove Quick

Page 14

Standard Horizontal Vent Installation

Installing Montage™ 32FS

All PL Venting Components must be listed to UL 641 or ULC S609

1.Locate the proper position for the listed type “PL” wall thimble. Avoid cutting wall studs when installing your pipe. Use a saber saw or keyhole saw to cut the proper diameter hole through the wall to accommodate the wall thimble. Use extreme caution to avoid cutting into power lines within the wall of the home. The hole size will depend on the brand of pellet vent that you are using. Install the wall thimble in the hole.

2.ALL INTERLOCKING PIPE CONNECTIONS MUST BE SEALED GAS- TIGHT AND SECURED TOGETHER PER VENT MANUFACTURERS INSTRUCTIONS.

Position the stove approximately 12” (305 mm) from the wall on the floor pad. Push the “PL” pipe through the wall thimble. Squeeze a bead of high temperature silicone (RTV) sealer around the end of the machined portion of the 3” (76 mm) pipe connector on the back of the stove. Firmly push on a section of “PL” pipe until inner pipe liner pushes into the bead of RTV sealer.

3.Push the stove with pipe attached towards the wall (the pipe will go through the wall thimble). Do not position the back of the stove closer than 2” (51 mm) from the wall (see Clearances, Page 5).

4.Install listed type “PL” 45 degree elbow with rodent screen or cap on outside end of pipe. The rodent screen should be no less than 1/2” (13 mm) mesh and may clog with soot and ash if left unattended during the burn season.

5.If the installation includes a source of outside combustion air; cut a separate hole through the wall for the fresh air tube. This tube should be 1-5/8” (42 mm) minimum diameter, steel only. Connect outside air pipe to air inlet on stove. This tube must be terminated with a 45 degree elbow or hood.

Notes:

•Combustion air may also be drawn from a vented crawl space under the home.

•All joints for connector pipe are required to be fastened together per the vent manufacturers instructions. If vented horizontally, joints must be made gas-tight (air tight, sealed connection) in a manner as specified on this page (see instruction #2). INSTALL VENT AT CLEARANCES

SPECIFIED BY THE VENT MANUFACTURER.

•Greater back clearance will improve the ease of serviceability of the stove.

•The end of the exhaust pipe must extend a minimum of 12” (305 mm) from the outside of the building.

Silicone sealant and 3 screws required on the first vent connection.

Secure and seal the remaining vent sections per vent manufacturers instructions.

Back of

 

Wall

 

Stove Quick

Straight “PL-vent”

45˚

Thimble

Disconnect

Pipe

Elbow

Exhaust

Port

Combustion

Air Inlet

Collar

 

 

Lytherm

Holes through

 

 

 

Metal Fresh

Gasket

the Wall for the

Air Pipe

 

 

Thimble &

 

 

 

 

 

 

 

 

 

Fresh Air Pipe

45o Degree Elbow Joint for Fresh Air Pipe

12” (305 mm) Min. From Outer Wall

12”(305 mm) From

Ground or Other Surface

14

Figure 15 - Horizontal Vent Installation

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Free-Standing Pellet Stove Important Safety and Warniing Information Is installedProduct is Subject to Change Without Notice Table of ContentsUsing this Manual Negative Pressure Warning Selecting a LocationFloor Protection Minimum Clearances To Combustibles ClearancesMontage 32FS Rear Wall or AlcoveHorizontal Installation Installation TipsSelect Your Installation Type Vertical & Horizontal InstallationBolt Chassis Floor Manufactured Home InstallationManufactured Home Exhaust Vent Pipe Installation Guidelines Removing Appliance From Pallet InstallationInstallation Check List Damper Location, Installation And Adjustment Venting Requirements = Clearance to inside corner *min /30cm Chimney Height Requirements Manufactured Homes Chimney Height Requirements Site Built Residential HomeSample Installation Chart Determining Size Of Pipe To InstallInstallation Chart Back Standard Horizontal Vent InstallationInstalling Montage 32FS Stove QuickHearth Pad / Floor Protection Min Wall51 mm Minimum Preferred Installation Vertical Vent Through the Roof MinSimple Operating Instructions Care and OperationStart Control Board Operation General Operating Considerations Pre-lighting InstructionsStarting Your Pellet Stove Manual and Automatic OperationTurning Off Your Stove Damper Adjustment GuidelineAutomatic Safety Features Damper OperationFuel Routine MaintenanceCleaning Fuel Feed RatesCleaning Behind Tube Scraper Heat Exchange TubesUnplug Stove Ash Slide Plate UltraGrate Burn GrateUltraGrate Ash PanGlass Cleaning After maintenance is complete, close the side panelsBlower Cleaning Door Rope GasketFlue Size Mm Rear Floor Protection Specifications Montage 32FSProduct Reference Information RequirementsComponent Definitions ANY ReasonTroubleshooting Qualified Technicians OnlyReplace the low limit thermal switch There is no power to the stoveClosed position Thermal switch and control board Heat exchanger area Vacuum cleaner is leakingItem # Cat. No Description GasketsReplacement Parts List Montage 32FS 1710Replacement Parts Diagrams Optional Accessories Item # Cat. No Model Description Optional AccessoriesAccessories Safety / listing label Lennox Hearth ProductsProduct reference information WarrantyReplacement parts 775,196M REV. NC 06/2008

32FS specifications

The Lennox Hearth 32FS is an exceptional fireplace designed to enhance both the aesthetic and functional aspects of any home. With its innovative technologies and user-friendly features, this model stands out as a premier choice for those looking to introduce warmth and elegance into their living space.

One of the primary features of the Lennox Hearth 32FS is its impressive heating capacity. With a BTU output that provides efficient heating to large areas, this fireplace is perfect for open floor plans or vast living rooms. This capability ensures that the space remains cozy and inviting even in the coldest months.

The combustion technology integrated into the Lennox Hearth 32FS is noteworthy as well. Utilizing a clean-burning system, it maximizes heat output while minimizing emissions, making it an environmentally-friendly option. The glass door design enhances air regulation and combustion efficiency, ensuring that homeowners get the most out of each burning cycle.

Another characteristic that sets the 32FS apart is its aesthetic appeal. The fireplace features a sleek and modern design, allowing it to blend seamlessly into various home decors, from traditional to contemporary. Customizable options, including different front designs and surround materials, allow homeowners to choose a look that aligns with their personal style.

Additionally, the Lennox Hearth 32FS provides ease of use and control. The model comes equipped with an intuitive remote control system, allowing users to adjust settings without leaving their seat. Whether it’s adjusting the flame height or configuring the thermostat, the convenience provided by this technology is undeniable.

Durability and build quality are other prominent aspects of the Lennox Hearth 32FS. Constructed from high-quality materials, it is designed to withstand the test of time, ensuring consistent performance year after year. The fireplace’s design includes advanced insulation techniques, which not only enhances efficiency but also ensures safety during operation.

In summary, the Lennox Hearth 32FS is a sophisticated fireplace featuring advanced heating capabilities, clean combustion technology, and a stylish design that caters to varying tastes. Its user-friendly controls and durable construction make it a reliable choice for anyone looking to invest in an energy-efficient heating solution that adds charm and comfort to their home.
Top Page Image Contents