Lennox Hearth 32FS operation manual Heat Exchange Tubes, Cleaning Behind Tube Scraper

Page 22

Heat Exchange Tubes

Tube Scraper - Using the hole in the handle of the Grate Scraper Tool “grab” the scraper rod as shown in Figure 26. Using the Grate Scraper Tool, pull the rod up and out towards the opening of the firebox. Con- tinue pulling until the Tube Scraper reaches the top of the firebox. Pull the tube scraper out, then repeat 2–3 times to remove fly-ash from the heat exchange tubes.

It may be easier to clean the tubes if the heat exchanger baffle plate is removed first (located in the firebox below exchange tubes).

Baffle Removal - The baffle plate contains two keyhole slots (see Fig- ures 24A and 24B), which allows the two retaining screws to remain in place while removing the baffle plate. To remove baffle, loosen the two screws holding the baffle in place (do not fully remove). Slide the baffle plate to the left until the screw heads clear the open end of the key hole slots. Remove the baffle plate diagonally through door opening. The tube scraper rod can now be pulled in a more horizontal manner, which allows the scraper to move more freely.

Note: The baffle plate should be removed at least once a year to allow for a thorough cleaning.

DETAIL A

 

DETAIL A

 

Baffle

Baffle

Screw

Plate

Brick

Brick

Panel

Retaining

 

Bracket

 

Figure 24A - Removing Baffle Plate

22

 

Front

Baffle Plate

Back

Keyhole Slots

(2 places)

Figure 24B - Removing Baffle Plate

Cleaning Behind Tube Scraper

WARNING

DO NOT USE BRUSH ON HOT STOVE

Clean between the heat exchange tubes using a cleaning brush as illus- trated in Figure 25.

With tube scraper rod pulled out 2 to 3 inches, insert brush behind tube scraper and remove ash build-up. Clean to the left and right side of heat exchanger, between tubes and the top of the firebox.

(Recommended Frequency of 2 weeks - 2 months)

Figure 25 - Clean Behind Tube Scraper

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Image 22
Contents Free-Standing Pellet Stove Important Safety and Warniing Information Is installedUsing this Manual Table of ContentsProduct is Subject to Change Without Notice Floor Protection Selecting a LocationNegative Pressure Warning Minimum Clearances To Combustibles ClearancesMontage 32FS Rear Wall or AlcoveHorizontal Installation Installation TipsSelect Your Installation Type Vertical & Horizontal InstallationManufactured Home Exhaust Vent Pipe Installation Guidelines Manufactured Home InstallationBolt Chassis Floor Installation Check List InstallationRemoving Appliance From Pallet Damper Location, Installation And Adjustment Venting Requirements = Clearance to inside corner *min /30cm Chimney Height Requirements Manufactured Homes Chimney Height Requirements Site Built Residential HomeInstallation Chart Determining Size Of Pipe To InstallSample Installation Chart Back Standard Horizontal Vent InstallationInstalling Montage 32FS Stove Quick51 mm Minimum Min WallHearth Pad / Floor Protection Preferred Installation Vertical Vent Through the Roof MinStart Care and OperationSimple Operating Instructions Control Board Operation General Operating Considerations Pre-lighting InstructionsStarting Your Pellet Stove Manual and Automatic OperationTurning Off Your Stove Damper Adjustment GuidelineAutomatic Safety Features Damper OperationFuel Routine MaintenanceCleaning Fuel Feed RatesCleaning Behind Tube Scraper Heat Exchange TubesUnplug Stove Ash Slide Plate UltraGrate Burn GrateUltraGrate Ash PanGlass Cleaning After maintenance is complete, close the side panelsBlower Cleaning Door Rope GasketFlue Size Mm Rear Floor Protection Specifications Montage 32FSProduct Reference Information RequirementsComponent Definitions ANY ReasonTroubleshooting Qualified Technicians OnlyReplace the low limit thermal switch There is no power to the stoveClosed position Thermal switch and control board Heat exchanger area Vacuum cleaner is leakingItem # Cat. No Description GasketsReplacement Parts List Montage 32FS 1710Replacement Parts Diagrams Optional Accessories Item # Cat. No Model Description Optional AccessoriesAccessories Safety / listing label Lennox Hearth ProductsProduct reference information WarrantyReplacement parts 775,196M REV. NC 06/2008

32FS specifications

The Lennox Hearth 32FS is an exceptional fireplace designed to enhance both the aesthetic and functional aspects of any home. With its innovative technologies and user-friendly features, this model stands out as a premier choice for those looking to introduce warmth and elegance into their living space.

One of the primary features of the Lennox Hearth 32FS is its impressive heating capacity. With a BTU output that provides efficient heating to large areas, this fireplace is perfect for open floor plans or vast living rooms. This capability ensures that the space remains cozy and inviting even in the coldest months.

The combustion technology integrated into the Lennox Hearth 32FS is noteworthy as well. Utilizing a clean-burning system, it maximizes heat output while minimizing emissions, making it an environmentally-friendly option. The glass door design enhances air regulation and combustion efficiency, ensuring that homeowners get the most out of each burning cycle.

Another characteristic that sets the 32FS apart is its aesthetic appeal. The fireplace features a sleek and modern design, allowing it to blend seamlessly into various home decors, from traditional to contemporary. Customizable options, including different front designs and surround materials, allow homeowners to choose a look that aligns with their personal style.

Additionally, the Lennox Hearth 32FS provides ease of use and control. The model comes equipped with an intuitive remote control system, allowing users to adjust settings without leaving their seat. Whether it’s adjusting the flame height or configuring the thermostat, the convenience provided by this technology is undeniable.

Durability and build quality are other prominent aspects of the Lennox Hearth 32FS. Constructed from high-quality materials, it is designed to withstand the test of time, ensuring consistent performance year after year. The fireplace’s design includes advanced insulation techniques, which not only enhances efficiency but also ensures safety during operation.

In summary, the Lennox Hearth 32FS is a sophisticated fireplace featuring advanced heating capabilities, clean combustion technology, and a stylish design that caters to varying tastes. Its user-friendly controls and durable construction make it a reliable choice for anyone looking to invest in an energy-efficient heating solution that adds charm and comfort to their home.