Lennox Hearth 32FS operation manual Component Definitions, ANY Reason

Page 27

COMPONENT DEFINITIONS

•Air Wash

A small slot in the door that allows room air to be pulled into the firebox and pours over the inside surface of the door glass to inhibit the build up of soot.

•Auger

A motor powered screw device that transfers the fuel from the hopper to the feed chute to deliver pellets to the UltraGrate™.

•Auger Motor

Drives the Auger. Motor specifications are: 0.5 Amp, 1.25 RPM (revolutions per minute).

•Blower, Room Air (Convection)

The blower function is to transfer the heat from the appliance to heat the room air.

•Blower, Exhaust (Combustion)

It has a radial impeller to deliver more air to the UltraGrate™. It pulls air into the UltraGrate by creating a negative pressure. This is done by extracting the exhaust gases out of the firebox and pushing the exhaust downstream to the flue exit.

•Thermal Switches, High Limit

There are three of these high-limit thermal switches on this model. If a temperature reaches the high limit temperature, the reset switch will “trip” and stop the flow of electricity to the auger motor. The thermal switches will not reset until they have cooled below low reset temperature).

-Auto Reset Thermal Snap Switch for Room Air Blower (L250- 30F, N/C*) – This switch will trip at 250° F and will automatically reset when it reaches a temperature of 220° F. This switch is located on the room air blower jacket and is designed to detect an overfire condition.

-Auto Reset Thermal Snap Switch for Combustion Air Inlet (L250-30F, N/C*) This switch will trip at 250° F and will auto- matically reset when it reaches a temperature of 220° F. This switch is designed to detect reversed flow or excessive heat in the ashpan area. This switch is located on the firebox base behind the convection jacket, directly above the ashpan. This switch is most easily accessed by removing the ashpan

-Manual Reset Thermal Snap Switch for Feed Chute (L300-145F, N/C*) This switch will trip at 300° F and will not be resettable until it reaches a temperature of 155° F. This switch is designed to detect if heat from the fire is approaching a path toward the hopper. If this switch trips it must be manually reset. To reset, open left side access door (facing stove), locate switch on the side of the auger tube and press the red button in the center until it clicks into the reset position.

•Thermal Switch, Low Limit (Ceramic, F140-20F, N/O*) - This "proof of fire" switch will close at 140° F and will not open until it reaches a temperature of 120° F. This switch is located on the combustion blower (behind the right side panel). It is designed to shut down the stove (auger motor and both blowers) if it does not detect the heat of a fire at the end of the initial startup period.

•Hopper Lid Switch

It is located on the left hinge area inside the hopper. It detects whether the hopper lid is open and will turn off the auger motor if the hopper lid is not properly closed. When opening the hopper when refueling, do not allow the hopper lid to remain open too long or the fire may extinguish. NEVER DISCONNECT OR BYPASS THIS SWITCH FOR

ANY REASON.

•Hopper

The hopper is where the pellets are stored.

•Heat Output Button

It controls power to the feed system - auger motor and combustion blower. Use the heat output button to adjust to any of the five feed rate settings (which controls the burn rate).

•Pressure Switch

A safety device used to shut off the feed system (auger motor) if there is too much back pressure in venting system. Some possible causes are as follows:

• The venting system is obstructed.

• High altitude or other misc. environmental conditions affecting exhaust flow.

• Improper venting system.

The Pressure Switch is located inside the right access door right next to the combustion blower.

•UltraGrate (Burn Grate)

This is where combustion occurs and may be referred to as the “Burn Grate”.

*N/C = Normally Closed N/O = Normally Open

YEL YEL

 

 

THERMOSTAT CONNECTOR

 

6-BRN

 

 

2

4

6

HI-LIMIT

HI-LIMIT MANUAL

HOPPER

PRESSURE

HI-LIMIT

AUTO-RESET

RESETTABLE

LID SWITCH

SWITCH

AUTO-RESET

SWITCH N/C

SWITCH N/C

N/C

N/C

SWITCH N/C

ABOVE ROOM

ON AUGER

LEFT HOPPER

INSIDE RIGHT

DIRECTLY

AIR BLOWER

TUBE

LID HINGE

ACCESS DOOR

ABOVE

 

 

AREA

 

ASHPAN

2-BLK

AUGER MOTOR

Montage TM 32FS

Wire Diagram

NOTE: SWITCH CONDITIONS GIVEN AT ROOM TEMPERATURE, STOVE OFF

POWER DISCONNECT

 

 

 

L

1

3

5

2-BLK

J P

CONV

N/C = NORMALLY CLOSED N/O = NORMALLY OPEN

 

HOT

3-RED

 

 

 

GND

 

4

3

N

NEUT

1-BLU

 

 

 

 

GRN

2

1

 

 

 

P/N 537039-01 Rev. NC

 

 

5-WHT

IGNITER FUSE

3-BLK

IGNITER

1-BLU

LO-LIMIT AUTO-RESET SWITCH N/O

ON COMBUSTION BLOWER HOUSING

J P 1-BLU 2-BLK

4-ORG

BLOWER

COMB

BLOWER

J = JACK

P = PLUG

= FEMALE DISCONNECT

= MALE DISCONNECT = STUD CONNECTION

IGN 08-2302

Figure 35 - WIRING DIAGRAM 120 V AC

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Free-Standing Pellet Stove Is installed Important Safety and Warniing InformationTable of Contents Using this ManualProduct is Subject to Change Without Notice Selecting a Location Floor ProtectionNegative Pressure Warning Rear Wall or Alcove ClearancesMontage 32FS Minimum Clearances To CombustiblesVertical & Horizontal Installation Installation TipsSelect Your Installation Type Horizontal InstallationManufactured Home Installation Manufactured Home Exhaust Vent Pipe Installation GuidelinesBolt Chassis Floor Installation Installation Check ListRemoving Appliance From Pallet Damper Location, Installation And Adjustment Venting Requirements = Clearance to inside corner *min /30cm Chimney Height Requirements Site Built Residential Home Chimney Height Requirements Manufactured HomesDetermining Size Of Pipe To Install Installation ChartSample Installation Chart Stove Quick Standard Horizontal Vent InstallationInstalling Montage 32FS BackMin Wall 51 mm MinimumHearth Pad / Floor Protection Min Preferred Installation Vertical Vent Through the RoofCare and Operation StartSimple Operating Instructions Control Board Operation Manual and Automatic Operation Pre-lighting InstructionsStarting Your Pellet Stove General Operating ConsiderationsDamper Operation Damper Adjustment GuidelineAutomatic Safety Features Turning Off Your StoveFuel Feed Rates Routine MaintenanceCleaning FuelHeat Exchange Tubes Cleaning Behind Tube ScraperUnplug Stove Ash Pan UltraGrate Burn GrateUltraGrate Ash Slide PlateDoor Rope Gasket After maintenance is complete, close the side panelsBlower Cleaning Glass CleaningRequirements Specifications Montage 32FSProduct Reference Information Flue Size Mm Rear Floor ProtectionANY Reason Component DefinitionsQualified Technicians Only TroubleshootingHeat exchanger area Vacuum cleaner is leaking There is no power to the stoveClosed position Thermal switch and control board Replace the low limit thermal switchGaskets Item # Cat. No Description1710 Replacement Parts List Montage 32FSReplacement Parts Diagrams Item # Cat. No Model Description Optional Accessories Optional AccessoriesAccessories Lennox Hearth Products Safety / listing label775,196M REV. NC 06/2008 WarrantyReplacement parts Product reference information

32FS specifications

The Lennox Hearth 32FS is an exceptional fireplace designed to enhance both the aesthetic and functional aspects of any home. With its innovative technologies and user-friendly features, this model stands out as a premier choice for those looking to introduce warmth and elegance into their living space.

One of the primary features of the Lennox Hearth 32FS is its impressive heating capacity. With a BTU output that provides efficient heating to large areas, this fireplace is perfect for open floor plans or vast living rooms. This capability ensures that the space remains cozy and inviting even in the coldest months.

The combustion technology integrated into the Lennox Hearth 32FS is noteworthy as well. Utilizing a clean-burning system, it maximizes heat output while minimizing emissions, making it an environmentally-friendly option. The glass door design enhances air regulation and combustion efficiency, ensuring that homeowners get the most out of each burning cycle.

Another characteristic that sets the 32FS apart is its aesthetic appeal. The fireplace features a sleek and modern design, allowing it to blend seamlessly into various home decors, from traditional to contemporary. Customizable options, including different front designs and surround materials, allow homeowners to choose a look that aligns with their personal style.

Additionally, the Lennox Hearth 32FS provides ease of use and control. The model comes equipped with an intuitive remote control system, allowing users to adjust settings without leaving their seat. Whether it’s adjusting the flame height or configuring the thermostat, the convenience provided by this technology is undeniable.

Durability and build quality are other prominent aspects of the Lennox Hearth 32FS. Constructed from high-quality materials, it is designed to withstand the test of time, ensuring consistent performance year after year. The fireplace’s design includes advanced insulation techniques, which not only enhances efficiency but also ensures safety during operation.

In summary, the Lennox Hearth 32FS is a sophisticated fireplace featuring advanced heating capabilities, clean combustion technology, and a stylish design that caters to varying tastes. Its user-friendly controls and durable construction make it a reliable choice for anyone looking to invest in an energy-efficient heating solution that adds charm and comfort to their home.
Top Page Image Contents