Lennox Hearth 32FS operation manual Manufactured Home Installation, Bolt Chassis Floor

Page 7

MANUFACTURED HOME INSTALLATION

In addition to the standard installation instructions, the following instruc- tions may be required by local, state or federal building codes:

• Installation should be in accordance with the Manufactured Home and

Safety Standard (HUD), CFR 3280, Part 24.

• The stove must be permanently bolted to the floor using two or three 1/4"

or 5/16" Ø x 5" lag screws as shown in Figures 4A, 4B, 5A and 5B.

• An outside air inlet must be provided for combustion and be unre-

stricted while unit is in use. Use a galvanized or stainless steel pipe

for the duct (the outside air inlet on the stove is 1-5/8” diameter).

The air intake on the exterior of the home should always be located

substantially below the flue termination. See Figures 4B and 15.

• Stove must be permanently electrically grounded to the steel chassis

of the home using a 8 GA copper wire and a serrated or star washer

(to penetrate paint or protective coating to ensure grounding). The

location selected for ground attachment to the stove must be dedicated

for this purpose. Grounding must comply with NFPA-70 standards,

CSA C22.1 in Canada, as well as any local codes.

• See Pages 9 through 15 for additional information on venting require-

Outside Air Inlet

Open front glass door and remove ash pan to access front lag screw hole.

 

ments.

•

WARNING: DO NOT INSTALL IN SLEEPING ROOM.

•

CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED

 

HOME FLOOR, WALLS, CEILING/ROOF MUST BE MAINTAINED.

Bolt

Bolt

 

Chassis

Floor

 

Protector

Floor

 

Figure 4A - Manufactured Home Installation

 

Holes for lag screws when securing to manufactured home floor

Options:

1)Install one lag screw in the front center hole and one in the rear center hole.

OR

2)Install one lag screw in the front center hole and two in the rear side holes.

Figure 4B - Manufactured Home Installation

Manufactured Home Exhaust Vent Pipe Installation Guidelines

Use only “PL” pellet vent pipe listed to UL 641 and ULC S609. The pipe should extend at least 3 feet above the part of the roof through which it passes. The top of the pipe should be at least 2 feet above the highest required elevation of any part of the manufactured home within 10 feet of the pipe (see Page 12, Manufactured Home Chimney Height Require- ments).

If the exhaust vent exits the manufactured home at a location other than the roof, and exits at a point 7 feet or less above the ground level on which the manufactured home is position a guard or method of enclosing the pipe shall be provided at the point of exit for a height of up to 7 feet. The openings, if any, in this guard shall not allow a 3/4” rod to pass through. A 1/2” rod could pass through but should not be able to touch the pipe when inserted through the opening a distance of 4 inches.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Free-Standing Pellet Stove Is installed Important Safety and Warniing InformationUsing this Manual Table of ContentsProduct is Subject to Change Without Notice Floor Protection Selecting a LocationNegative Pressure Warning Rear Wall or Alcove ClearancesMontage 32FS Minimum Clearances To CombustiblesVertical & Horizontal Installation Installation TipsSelect Your Installation Type Horizontal InstallationManufactured Home Exhaust Vent Pipe Installation Guidelines Manufactured Home InstallationBolt Chassis Floor Installation Check List InstallationRemoving Appliance From Pallet Damper Location, Installation And Adjustment Venting Requirements = Clearance to inside corner *min /30cm Chimney Height Requirements Site Built Residential Home Chimney Height Requirements Manufactured HomesInstallation Chart Determining Size Of Pipe To InstallSample Installation Chart Stove Quick Standard Horizontal Vent InstallationInstalling Montage 32FS Back51 mm Minimum Min WallHearth Pad / Floor Protection Min Preferred Installation Vertical Vent Through the RoofStart Care and OperationSimple Operating Instructions Control Board Operation Manual and Automatic Operation Pre-lighting InstructionsStarting Your Pellet Stove General Operating ConsiderationsDamper Operation Damper Adjustment GuidelineAutomatic Safety Features Turning Off Your StoveFuel Feed Rates Routine MaintenanceCleaning FuelHeat Exchange Tubes Cleaning Behind Tube ScraperUnplug Stove Ash Pan UltraGrate Burn GrateUltraGrate Ash Slide PlateDoor Rope Gasket After maintenance is complete, close the side panelsBlower Cleaning Glass CleaningRequirements Specifications Montage 32FSProduct Reference Information Flue Size Mm Rear Floor ProtectionANY Reason Component DefinitionsQualified Technicians Only TroubleshootingHeat exchanger area Vacuum cleaner is leaking There is no power to the stoveClosed position Thermal switch and control board Replace the low limit thermal switchGaskets Item # Cat. No Description1710 Replacement Parts List Montage 32FSReplacement Parts Diagrams Item # Cat. No Model Description Optional Accessories Optional AccessoriesAccessories Lennox Hearth Products Safety / listing label775,196M REV. NC 06/2008 WarrantyReplacement parts Product reference information

32FS specifications

The Lennox Hearth 32FS is an exceptional fireplace designed to enhance both the aesthetic and functional aspects of any home. With its innovative technologies and user-friendly features, this model stands out as a premier choice for those looking to introduce warmth and elegance into their living space.

One of the primary features of the Lennox Hearth 32FS is its impressive heating capacity. With a BTU output that provides efficient heating to large areas, this fireplace is perfect for open floor plans or vast living rooms. This capability ensures that the space remains cozy and inviting even in the coldest months.

The combustion technology integrated into the Lennox Hearth 32FS is noteworthy as well. Utilizing a clean-burning system, it maximizes heat output while minimizing emissions, making it an environmentally-friendly option. The glass door design enhances air regulation and combustion efficiency, ensuring that homeowners get the most out of each burning cycle.

Another characteristic that sets the 32FS apart is its aesthetic appeal. The fireplace features a sleek and modern design, allowing it to blend seamlessly into various home decors, from traditional to contemporary. Customizable options, including different front designs and surround materials, allow homeowners to choose a look that aligns with their personal style.

Additionally, the Lennox Hearth 32FS provides ease of use and control. The model comes equipped with an intuitive remote control system, allowing users to adjust settings without leaving their seat. Whether it’s adjusting the flame height or configuring the thermostat, the convenience provided by this technology is undeniable.

Durability and build quality are other prominent aspects of the Lennox Hearth 32FS. Constructed from high-quality materials, it is designed to withstand the test of time, ensuring consistent performance year after year. The fireplace’s design includes advanced insulation techniques, which not only enhances efficiency but also ensures safety during operation.

In summary, the Lennox Hearth 32FS is a sophisticated fireplace featuring advanced heating capabilities, clean combustion technology, and a stylish design that caters to varying tastes. Its user-friendly controls and durable construction make it a reliable choice for anyone looking to invest in an energy-efficient heating solution that adds charm and comfort to their home.
Top Page Image Contents