Lennox Hearth L30 DVF-2 operation manual Vertical Vent Termination Clearances, SV4MCK

Page 10

INSTALLATION

DIRECT VENT RETROFIT OF EXISTING CHIMNEY SYSTEM - An existing Class-A (wood-burning) Metal Chimney or Masonry Chimney can be converted to a direct vent system. Use one of the following chimney conversion kits listed below. Have the existing chimney system inspected by a professional prior to the conversion. If using Simpson Dura-Vent brand liner kit, see “IMPORTANT” note at the top of page 9. The chimney conversion should not be applied to the portion of the vent system that is in the room of the appliance. Use only Co-Axial direct vent pipe (4” inner pipe, 6 5/8” outer pipe as listed on page 9) from the appliance to the retro-connector into converted flue system. Adhere to all specifications shown on pages 6 and 7 regarding clearances to combustibles, vertical and hori- zontal vent length minimums and maximums, etc. Read all instructions in this manual and provided by vent manufacturer with kit care- fully before starting the installation. Failure to follow the instructions may create a fire or other safety hazard, and will void the war- ranty.

Model #

Brand: SECURITY / Description

Model #

Brand: SIMPSON DURA-VENT / Description

SV4MCK

Masonry Chimney Conversion Kit –Vertical term. Cap, cap adapter,

934

Masonry Chimney Conversion Kit

 

masonry cover, black adapter (to flex), 2 gear clamps

 

 

SV4CCK1

Factory Built Chimney Conversion Kit – for 6” I.D., 1” insulation.

931

Factory Built Chimney Conversion Kit A – for 6” I.D.; Only compati-

 

 

 

ble w/specific brands – Contact Vent Manufacturer

SV4CCK2

Factory Built Chimney Conversion Kit – for 7” I.D., 1” insulation; 8” I.D.,

932

Factory Built Chimney Conversion Kit B – for 6”, 7” & 8” I.D.; Only

 

1” insulation; 6” I.D., 2” insulation.

 

compatible w/specific brands – Contact Vent Manufacturer

SV4CCK3

Factory Built Chimney Conversion Kit – for 10” I.D., 1” insulation; 7” I.D.,

933

Factory Built Chimney Conversion Kit C – for 7” & 8” I.D.; Only

 

2” insulation; 8” I.D., 2” insulation.

 

compatible w/specific brands – Contact Vent Manufacturer

VERTICAL VENT TERMINATION CLEARANCES

These instructions should be used as a guideline and do not su- persede local codes in any way. Install vent according to local codes, these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the current standards of CAN/CGA- B149.1 and -B149.2 in Canada.

Terminate multiple vent terminations according to the installation codes listed above.

Terminate single vent caps relative to building components ac- cording to the following chart & illustration. The vent/air intake termination clearances above the high side of an angled roof is

as shown in the following chart:

.

Termination Heights For Vents Above Flat

or Sloped Roofs

Roof Pitch

Feet

Meters

Flat to 6/12

1

0.3

6/12 to 7/12

1.25

0.38

7/12 to 8/12

1.5

0.46

8/12 to 9/12

2

0.61

9/12 to 10/12

2.5

0.76

10/12 to 11/12

3.25

0.99

11/12 to 12/12

4

1.22

12/12 to 14/12

5

1.52

14/12 to 16/12

6

1.83

16/12 to 18/12

7

2.13

18/12 to 20/12

7.5

2.29

20/12 to 21/12

8

2.44

Termination Heights For Vents Above Flat or Sloped Roofs

 

Horizontal Overhang

 

2 Ft. Min.

2 Ft. Min.

Vertical

 

 

Lowest

Wall

 

 

 

Discharge

 

 

Opening

 

Vent

 

 

Termination

 

 

Storm

* H

 

 

X

Collar

 

 

12

Flashing

 

 

Roof Pitch is X/12

 

 

 

1 inch (25.4 mm) Minimum

 

Clearance to Combustibles

Concentric

* H = Minimum height from roof to

Vent Pipe

lowest discharge opening of vent.

PAGE 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Retain this Manual for Future Reference Freestanding Vented GAS Fired Room Heaters775,029M Rev. B, 8/04 Important Warnings / Cautions Table of Contents Tool / Equipment List Planning Your InstallationLocal and National Code Requirements LOW HighQuestions to ASK the Local Building Official Rear Wall or Alcove Clearances to Combustible MaterialsManufactured Mobile Home Requirements CornerMax. Vertical Pipe Length 25 feet InstallationMax. Total Vertical Pipe Length 25 feet Vent Restrictor Ring Installation Symptoms Excessive Combustion AirDirect Vent System Components Model L30 DVF-2 SV 0 SHKVertical Vent Termination Clearances SV4MCKHorizontal Vent Termination Requirements GAS Supply Hookup Pressure TestingSupply Line Size Requirements Door Operation Installing LOG SET GAS Appliance Final AssemblyGlowing Embers Installation Check List Adjust gap as shown in following pictureGas Control Knobs Pilot AssemblyCare and Operation Lighting and Shutdown InstructionsCirculation Blower Operation BREAK-IN PeriodCombustion Chamber Relief Doors Variable Speed Control for Air Circulation BlowerPropane Conversion Parts ListPropane Conversion Procedure CanadaReference Information Burner Flame AppearanceMaintenance Cycle unit a minimum of 2 times Air Shutter AdjustmentPeriodic Check of Pilot and Burner Flames Pilot Flame AppearanceGAS Control and Safety System Wiring Diagram Wiring DiagramsCirculating Blower Wiring Diagram Troubleshooting Qualified Technicians Only Replacement Parts Model L30 DVF-2 Item # Description Cat. NoOptional Accessories Item # Description Catalog # ModelVented Gas Fireplace Heater Safety TestDards. Z21.88-1998 CSA 2.33a M98 Top View Side ViewSafety / Listing Label Rating Plate Service and Maintenance LOG Ownership Records775,029M REV. B 08/2004

L30 DVF-2 specifications

The Lennox Hearth L30 DVF-2 is an impressive direct vent gas fireplace known for its aesthetic appeal and innovative technologies. This model stands out in the realm of residential heating solutions, combining efficiency, performance, and design into a singular unit that enhances any living space.

One of the primary features of the L30 DVF-2 is its efficient heating capacity. With a heating output of up to 30,000 BTUs, it effectively warms large areas while maintaining a steady and comfortable indoor climate. This model uses a direct vent system, allowing for clean and safe operation by taking air from the outside for combustion and expelling exhaust gases outside as well. This not only minimizes the risk of indoor air pollution but also allows for versatile installation options without the need for a traditional chimney.

In terms of design, the L30 DVF-2 offers a sleek and modern appearance, making it a stylish addition to any room. The fireplace features a large viewing area with a contemporary surround that can be customized in various finishes to match the décor of your home. Additionally, a variety of decorative options such as glass media and ceramic logs add to its aesthetic appeal, providing a beautiful flame presentation.

The Lennox L30 DVF-2 is also equipped with advanced technology, including an electronic ignition system that ensures reliable startups without requiring manual assistance. The fireplace can be conveniently controlled using a wall switch or remote control, allowing users to adjust the heat and flame settings with ease. The model is designed with a blower option that enhances heat distribution, helping to circulate warm air throughout the room more effectively.

Moreover, energy efficiency is a hallmark of the L30 DVF-2. Rated with a high Annual Fuel Utilization Efficiency (AFUE), this fireplace not only provides warmth but does so while minimizing energy consumption and utility costs. This efficiency extends the value of your investment by ensuring lower operating expenses over time.

Overall, the Lennox Hearth L30 DVF-2 combines cutting-edge technology, aesthetic versatility, and energy efficiency into a gas fireplace that offers both style and substance. It caters to modern homeowners looking to enhance their living spaces with a reliable and attractive heating solution.
Top Page Image Contents