Clearances to Combustible Materials

PLANNING YOUR INSTALLATION

These appliances can be installed in most residential room configura- tions, parallel to a rear or adjacent wall, or in an alcove that allows for the minimum clearances to combustible surfaces. Your local building inspector should review your plans prior to installation.

When installing this appliance, provide adequate clearances around air openings and adequate clearances for purposes of servicing and proper operation.

As determined through the safety certification of this unit, a mini- mum clearance to combustible materials must be maintained around specific areas of the gas appliance. (Refer to Figures 1 through 3)

The clearances listed here are minimum distances and only apply in the configuration shown. Do not use clearances from one installation configuration with clearances from another to obtain closer clear- ances.

Top of appliance (min.)

36” (inches)

This includes any projections such as shelves, window sills, mantels, etc. above the appliance.

Back Wall	2" (inches)
Side Wall	12" (inches)
Corner (45° angle)	4" (inches)
stove corners to wall
Ceiling Minimum	65" (inches) from floor
Alcove Min. Height	65" (inches) from floor
Alcove Min. Width	53 7/8" (inches)
Alcove Max. Depth	24" (inches) from unit face.

The stove can not be placed deeper into an alcove than 24” from the stove face to alcove opening.

Floor

0 inches

MANUFACTURED (MOBILE) HOME REQUIREMENTS

Model L30 DVF-2 may be installed in an aftermarket perma- nently located, manufactured home, where not prohibited by local codes. When installed in Manufactured Housing the follow- ing supplemental requirements must be met:

The appliance must be secured to the floor. Use the (3) ¼”-20x2 ¾” lag bolts (which secured appliance pedestal base to the wooden pallet) for securing appliance to the manufactured home floor.

The appliance must be grounded to the chassis of the manufac- tured home. Use a No. 8 or heavier copper wire at least 18" in length.

IMPORTANT NOTES:

The structural integrity of the manufactured home floor, walls, ceiling and roof must be maintained.

A manufactured (mobile) home installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSI / NCSBCS A225.1, or standard for Gas equipped Recreational Vehicles and Mobile Hous- ing, CSA Z240.4.

PAGE 6

Rear Wall or Alcove

65Inch

(1651 mm) Min. Ceiling Height

2” Min. (51 mm)

Fig. 1

Corner

4” Min. (102 mm)

Fig. 2	4” Min.
Fig. 2	(102 mm)


	Rear Wall or Alcove
	2” Min. (51 mm)
	Ref. 30 1/8” (765 mm)
12” Min.	12” Min.
(305 mm)	(305 mm)
Fig. 3	24” Max. (610 mm)
Fig. 3

FLOOR PROTECTION

When installed directly on carpeting, •tile or other combusti- ble material other than wood flooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance (♦ see notes below).

♦Notes:

1)Ceramic tile is non-combustible and does not require a wood or metal panel under the appliance. 2) Models with a pedestal base where base dimensions exceed width and depth of stove body, qualify as the floor protection

L30 DVF-2 specifications

The Lennox Hearth L30 DVF-2 is an impressive direct vent gas fireplace known for its aesthetic appeal and innovative technologies. This model stands out in the realm of residential heating solutions, combining efficiency, performance, and design into a singular unit that enhances any living space.

One of the primary features of the L30 DVF-2 is its efficient heating capacity. With a heating output of up to 30,000 BTUs, it effectively warms large areas while maintaining a steady and comfortable indoor climate. This model uses a direct vent system, allowing for clean and safe operation by taking air from the outside for combustion and expelling exhaust gases outside as well. This not only minimizes the risk of indoor air pollution but also allows for versatile installation options without the need for a traditional chimney.

In terms of design, the L30 DVF-2 offers a sleek and modern appearance, making it a stylish addition to any room. The fireplace features a large viewing area with a contemporary surround that can be customized in various finishes to match the décor of your home. Additionally, a variety of decorative options such as glass media and ceramic logs add to its aesthetic appeal, providing a beautiful flame presentation.

The Lennox L30 DVF-2 is also equipped with advanced technology, including an electronic ignition system that ensures reliable startups without requiring manual assistance. The fireplace can be conveniently controlled using a wall switch or remote control, allowing users to adjust the heat and flame settings with ease. The model is designed with a blower option that enhances heat distribution, helping to circulate warm air throughout the room more effectively.

Moreover, energy efficiency is a hallmark of the L30 DVF-2. Rated with a high Annual Fuel Utilization Efficiency (AFUE), this fireplace not only provides warmth but does so while minimizing energy consumption and utility costs. This efficiency extends the value of your investment by ensuring lower operating expenses over time.

Overall, the Lennox Hearth L30 DVF-2 combines cutting-edge technology, aesthetic versatility, and energy efficiency into a gas fireplace that offers both style and substance. It caters to modern homeowners looking to enhance their living spaces with a reliable and attractive heating solution.