Axis Communications Q6045-E user manual Controls

Page 29

AXIS Q6045-E Mk II PTZ Dome Network Camera

PTZ (Pan Tilt Zoom)

Near focus limit is used to prevent the camera from autofocusing on objects close to the camera. This way, the camera can ignore objects such as overhead wires, streetlights, or other cameras placed close to the camera.

To make the camera focus on the areas of interest, set the near focus limit to a value that is greater than the distance at which the uninteresting objects tend to appear. See illustration below where x is the near focus limit value.

Move speed sets the speed of the camera’s pan and tilt movements. The default setting is maximum speed.

When using a joystick (or emulating one with the mouse) the Enable proportional speed setting can be used to reduce the maximum pan/tilt movement speed, i.e. the speed the camera view moves at when the joystick is pushed all the way out in any direction. This is useful then the view is zoomed in on an object.

See the online help for more information.

Controls

Advanced PTZ settings can be configured under PTZ > Advanced > Controls.

The Panel Shortcut Command Buttons list shows the user-defined buttons that can be accessed from the Live View page’s Ctrl panel. These buttons can be used to provide direct access to commands issued using the VAPIX® application programming interface. Click Add to add a new shortcut command button.

The following PTZ controls are enabled by default:

•Pan control

•Tilt control

•Zoom control

•Focus control

•Iris control

To disable specific controls, deselect the options under Enable/Disable controls.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Axis Q6045-E Mk II PTZ Dome Network Camera Legal Considerations About this documentLiability Intellectual Property RightsLearn More SupportAxis Q6045-E Mk II PTZ Dome Network Camera Table of ContentsConnectors Performance Considerations Network Connector Connectors and ButtonsFor technical specifications, see Hardware OverviewPower Button LED IndicatorsSD Card Slot Control ButtonGreen Steady when AC power input connected Midspan LED IndicatorsAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordLive View Go to Setup EventsControls on the Live View Click Use HttpsTo show the manual trigger buttons in the Live View Axis Media Control viewer toolbarPTZ Controls Autotracking on Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis Q6045-E Mk II PTZ Dome Network Camera Basic Setup Set Up the ProductVideo Click Save to apply the new settingsVideo Stream Pixel Counter264 Stream ProfilesExposure Settings Camera SettingsImage Appearance White BalanceGo to Video Video Stream and select the Image tab Image SettingsOverlay Go to Video Overlay Image Overlay ImageUse Overlay Text in an Action Rule Go to Events Action Rules Under Overlay Settings, select Include textPrivacy Mask Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links PTZ Pan Tilt Zoom Preset PositionsAutotracking ConfigurationExclude Areas Max LimitsTo add a guard tour GatekeeperGuard Tour Advanced Osdi ZonesTour Recording LimitsControls Control Queue Operator Same as administrator but with lower priorityDetectors Set Up Motion Detection WindowsShock Detection Motion DetectionObject Removed Basic Video AnalyticsEnter/Exit Detector Object Counter Fence DetectorObservations Be activated See the online help for more informationGo to Setup Applications Install ApplicationApplications Application LicensesAxis Q6045-E Mk II PTZ Dome Network Camera Events Set Up Action RulesTriggers Go to Events Action Rules and click AddHardware Input SignalStorage SystemRecipient Types Add RecipientsActions Recipient Use with action Set Up Email RecipientsCreate Schedules Set Up RecurrencesTo create a new schedule Go to Events Schedules and click AddRecording List RecordingsContinuous Recording Go to Recordings ListLanguages Security System OptionsUsers IP Address FilterGo to System Options Security Ieee IeeeCertificates Go to Setup System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkIPv6 Address Configuration IPv4 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM StorageRTP/H.264 BonjourFormat SD Card Mount and Unmount SD CardNetwork Share MaintenanceTo add a network share Go to System Options Storage Click Network ShareSupport Plain Config Reset to Factory Default SettingsUpgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Video Camera Settings Key framesCondensation in dome Storage and disk management problemsTechnical Specifications Installation aid Function/group Specifications Network SecurityInstallation MaintenancePower Function/group Specifications General CasingConnectors WeightPerformance Considerations ConnectorsM4.2
Related manuals
Manual 24 pages 14.82 Kb Manual 61 pages 17.77 Kb

Q6045-E specifications

Axis Communications Q6045-E is an advanced network camera designed specifically for professional surveillance applications. This camera exemplifies Axis's commitment to high-performance video surveillance solutions, combining cutting-edge technology with robust design features.

One of the standout characteristics of the Q6045-E is its exceptional imaging capabilities. Equipped with a 1/2.8” sensor, it delivers high-resolution video at up to 1080p, ensuring clear and detailed images even in challenging lighting conditions. The camera supports a wide dynamic range (WDR), enabling it to capture high-quality images in environments with varying light levels, such as areas that experience both bright sunlight and deep shadows.

The Q6045-E also integrates a powerful 30x optical zoom lens, which allows for detailed close-ups of objects at a distance. This feature is essential for applications requiring precise identification, such as monitoring perimeters, parking lots, and business premises. The camera includes intelligent video analytics capabilities, providing features like motion detection, tampering alarm, and audio detection, enhancing the effectiveness of security measures.

Another noteworthy aspect is the camera’s PTZ (pan-tilt-zoom) functionality. It can pan 360 degrees and tilt from -20 to 90 degrees, providing extensive coverage and flexibility for optimal surveillance. This means a single Q6045-E can monitor vast areas, reducing the need for multiple cameras and thus lowering overall system costs.

Durability and reliability are also key features of the Q6045-E. Designed for outdoor use, the camera is IP66-rated and NEMA 4X-rated, which means it can withstand harsh weather conditions, including rain, snow, and extreme temperatures. The built-in heater ensures consistent performance in cold environments, maintaining both functionality and image quality.

The camera is powered over Ethernet (PoE), facilitating easy installation with just one cable for both data and power. This simplifies the setup process and reduces additional wiring costs. Additionally, the Q6045-E supports various video compression formats, including H.264 and H.265, allowing for efficient bandwidth usage without compromising video quality.

In conclusion, Axis Communications Q6045-E is a feature-rich choice for any professional surveillance system, offering high-resolution video, intelligent analytics, robust durability, and flexible installation options. Its innovative technologies make it an ideal solution for enhancing security and surveillance efforts in a wide range of environments.
Top Page Image Contents