Axis Communications Q6045-E user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 52

AXIS Q6045-E Mk II PTZ Dome Network Camera

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 45. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 56.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see www.axis.com

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Axis Q6045-E Mk II PTZ Dome Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q6045-E Mk II PTZ Dome Network CameraConnectors Performance Considerations Connectors and Buttons Network ConnectorFor technical specifications, see Hardware OverviewLED Indicators Power ButtonSD Card Slot Control ButtonMidspan LED Indicators Green Steady when AC power input connectedAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordGo to Setup Events Live ViewControls on the Live View Click Use HttpsPTZ Controls Axis Media Control viewer toolbarTo show the manual trigger buttons in the Live View Autotracking on Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis Q6045-E Mk II PTZ Dome Network Camera Set Up the Product Basic SetupClick Save to apply the new settings VideoVideo Stream Pixel CounterStream Profiles 264Camera Settings Exposure SettingsImage Appearance White BalanceOverlay Image SettingsGo to Video Video Stream and select the Image tab Use Overlay Text in an Action Rule Overlay ImageGo to Video Overlay Image Privacy Mask Under Overlay Settings, select Include textGo to Events Action Rules Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionUser Defined Links Preset Positions PTZ Pan Tilt ZoomConfiguration AutotrackingExclude Areas Max LimitsGuard Tour GatekeeperTo add a guard tour Osdi Zones AdvancedTour Recording LimitsControls Operator Same as administrator but with lower priority Control QueueSet Up Motion Detection Windows DetectorsShock Detection Motion DetectionBasic Video Analytics Object RemovedEnter/Exit Detector Fence Detector Object CounterBe activated See the online help for more information ObservationsInstall Application Go to Setup ApplicationsApplications Application LicensesAxis Q6045-E Mk II PTZ Dome Network Camera Set Up Action Rules EventsTriggers Go to Events Action Rules and click AddInput Signal HardwareStorage SystemActions Add RecipientsRecipient Types Set Up Email Recipients Recipient Use with actionSet Up Recurrences Create SchedulesTo create a new schedule Go to Events Schedules and click AddRecordings Recording ListContinuous Recording Go to Recordings ListLanguages System Options SecurityUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee Basic TCP/IP Settings Go to Setup System Options Security CertificatesDate & Time NetworkIPv4 Address Configuration IPv6 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPStorage UPnPTMRTP/H.264 BonjourMount and Unmount SD Card Format SD CardMaintenance Network ShareTo add a network share Go to System Options Storage Click Network ShareSupport Reset to Factory Default Settings Plain ConfigTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, generalVideo Camera Settings Key framesStorage and disk management problems Condensation in domeTechnical Specifications Function/group Specifications Network Security Installation aidInstallation MaintenanceFunction/group Specifications General Casing PowerConnectors WeightConnectors Performance ConsiderationsM4.2
Related manuals
Manual 24 pages 14.82 Kb Manual 61 pages 17.77 Kb

Q6045-E specifications

Axis Communications Q6045-E is an advanced network camera designed specifically for professional surveillance applications. This camera exemplifies Axis's commitment to high-performance video surveillance solutions, combining cutting-edge technology with robust design features.

One of the standout characteristics of the Q6045-E is its exceptional imaging capabilities. Equipped with a 1/2.8” sensor, it delivers high-resolution video at up to 1080p, ensuring clear and detailed images even in challenging lighting conditions. The camera supports a wide dynamic range (WDR), enabling it to capture high-quality images in environments with varying light levels, such as areas that experience both bright sunlight and deep shadows.

The Q6045-E also integrates a powerful 30x optical zoom lens, which allows for detailed close-ups of objects at a distance. This feature is essential for applications requiring precise identification, such as monitoring perimeters, parking lots, and business premises. The camera includes intelligent video analytics capabilities, providing features like motion detection, tampering alarm, and audio detection, enhancing the effectiveness of security measures.

Another noteworthy aspect is the camera’s PTZ (pan-tilt-zoom) functionality. It can pan 360 degrees and tilt from -20 to 90 degrees, providing extensive coverage and flexibility for optimal surveillance. This means a single Q6045-E can monitor vast areas, reducing the need for multiple cameras and thus lowering overall system costs.

Durability and reliability are also key features of the Q6045-E. Designed for outdoor use, the camera is IP66-rated and NEMA 4X-rated, which means it can withstand harsh weather conditions, including rain, snow, and extreme temperatures. The built-in heater ensures consistent performance in cold environments, maintaining both functionality and image quality.

The camera is powered over Ethernet (PoE), facilitating easy installation with just one cable for both data and power. This simplifies the setup process and reduces additional wiring costs. Additionally, the Q6045-E supports various video compression formats, including H.264 and H.265, allowing for efficient bandwidth usage without compromising video quality.

In conclusion, Axis Communications Q6045-E is a feature-rich choice for any professional surveillance system, offering high-resolution video, intelligent analytics, robust durability, and flexible installation options. Its innovative technologies make it an ideal solution for enhancing security and surveillance efforts in a wide range of environments.
Top Page Image Contents