Axis Communications Q6045-E user manual Events, Set Up Action Rules, Triggers, Detectors

Page 38

AXIS Q6045-E Mk II PTZ Dome Network Camera

Events

Events

The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.

Set Up Action Rules

An action rule defines the conditions that must be met for the product to perform an action, for example record video or send an email notification. If multiple conditions are defined, all of them must be met to trigger the action.

For more information about available triggers and actions, see Triggers on page 38 and Actions on page 40.

The following example describes how to set up an action rule to record video to a network share if there is movement in the camera’s field of view.

Set up motion detection and add a network share:

1.Go to Detectors > Motion Detection and configure a motion detection window. See page 31

2.Go to System Options > Storage and set up the network share. See page 54.

Set up the action rule:

1.Go to Events > Action Rules and click Add.

2.Select Enable rule and enter a descriptive name for the rule.

3.Select Detectors from the Trigger drop-down list.

4.Select Motion Detection from the drop-down list. Select the motion detection window to use.

5.Optionally, select a Schedule and Additional conditions. See below.

6.Under Actions, select Record Video from the Type drop-down list.

7.Select a Stream profile and configure the Duration settings as described below.

8.Select Network Share from the Storage drop-down list.

To use more than one trigger for the action rule, select Additional conditions and click Add to add additional triggers. When using additional conditions, all conditions must be met to trigger the action.

To prevent an action from being triggered repeatedly, a Wait at least time can be set. Enter the time in hours, minutes and seconds, during which the trigger should be ignored before the action rule can be activated again.

The recording Duration of some actions can be set to include time immediately before and after the event. Select Pre-trigger time and/or Post-trigger time and enter the number of seconds. When While the rule is active is enabled and the action is triggered again during the post-trigger time, the recording time will be extended with another post-trigger time period.

For more information, see the online help .

Triggers

Available action rule triggers and conditions include:

Applications – Use installed applications to trigger the rule. See Applications on page 36.

Detectors

38

Image 38
Contents Axis Q6045-E Mk II PTZ Dome Network Camera Liability About this documentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q6045-E Mk II PTZ Dome Network CameraConnectors Performance Considerations For technical specifications, see Connectors and ButtonsNetwork Connector Hardware OverviewSD Card Slot LED IndicatorsPower Button Control ButtonMidspan LED Indicators Green Steady when AC power input connectedAccess from the Internet Access the ProductAccess from a Browser Set the Root PasswordControls on the Live View Go to Setup EventsLive View Click Use HttpsTo show the manual trigger buttons in the Live View Axis Media Control viewer toolbarPTZ Controls Autotracking on Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis Q6045-E Mk II PTZ Dome Network Camera Set Up the Product Basic SetupVideo Stream Click Save to apply the new settingsVideo Pixel CounterStream Profiles 264Image Appearance Camera SettingsExposure Settings White BalanceGo to Video Video Stream and select the Image tab Image SettingsOverlay Go to Video Overlay Image Overlay ImageUse Overlay Text in an Action Rule Go to Events Action Rules Under Overlay Settings, select Include textPrivacy Mask Viewer Settings Configure the Live ViewDefault Viewer for Browsers Browser Viewer DescriptionUser Defined Links Preset Positions PTZ Pan Tilt ZoomExclude Areas ConfigurationAutotracking Max LimitsTo add a guard tour GatekeeperGuard Tour Tour Recording Osdi ZonesAdvanced LimitsControls Operator Same as administrator but with lower priority Control QueueShock Detection Set Up Motion Detection WindowsDetectors Motion DetectionBasic Video Analytics Object RemovedEnter/Exit Detector Fence Detector Object CounterBe activated See the online help for more information ObservationsApplications Install ApplicationGo to Setup Applications Application LicensesAxis Q6045-E Mk II PTZ Dome Network Camera Triggers Set Up Action RulesEvents Go to Events Action Rules and click AddStorage Input SignalHardware SystemRecipient Types Add RecipientsActions Set Up Email Recipients Recipient Use with actionTo create a new schedule Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddContinuous Recording RecordingsRecording List Go to Recordings ListLanguages Users System OptionsSecurity IP Address FilterGo to System Options Security Ieee IeeeCertificates Date & Time Basic TCP/IP SettingsGo to Setup System Options Security Certificates NetworkAssign IP Address Using ARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration ARP/PingAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 StorageUPnPTM BonjourMount and Unmount SD Card Format SD CardTo add a network share MaintenanceNetwork Share Go to System Options Storage Click Network ShareSupport Reset to Factory Default Settings Plain ConfigEmergency Recovery Procedure TroubleshootingUpgrade the Firmware Check the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyVideo Camera Settings Problems with streaming H.264Video and image problems, general Key framesStorage and disk management problems Condensation in domeTechnical Specifications Installation Function/group Specifications Network SecurityInstallation aid MaintenanceConnectors Function/group Specifications General CasingPower WeightConnectors Performance ConsiderationsM4.2
Related manuals
Manual 24 pages 14.82 Kb Manual 61 pages 17.77 Kb

Q6045-E specifications

Axis Communications Q6045-E is an advanced network camera designed specifically for professional surveillance applications. This camera exemplifies Axis's commitment to high-performance video surveillance solutions, combining cutting-edge technology with robust design features.

One of the standout characteristics of the Q6045-E is its exceptional imaging capabilities. Equipped with a 1/2.8” sensor, it delivers high-resolution video at up to 1080p, ensuring clear and detailed images even in challenging lighting conditions. The camera supports a wide dynamic range (WDR), enabling it to capture high-quality images in environments with varying light levels, such as areas that experience both bright sunlight and deep shadows.

The Q6045-E also integrates a powerful 30x optical zoom lens, which allows for detailed close-ups of objects at a distance. This feature is essential for applications requiring precise identification, such as monitoring perimeters, parking lots, and business premises. The camera includes intelligent video analytics capabilities, providing features like motion detection, tampering alarm, and audio detection, enhancing the effectiveness of security measures.

Another noteworthy aspect is the camera’s PTZ (pan-tilt-zoom) functionality. It can pan 360 degrees and tilt from -20 to 90 degrees, providing extensive coverage and flexibility for optimal surveillance. This means a single Q6045-E can monitor vast areas, reducing the need for multiple cameras and thus lowering overall system costs.

Durability and reliability are also key features of the Q6045-E. Designed for outdoor use, the camera is IP66-rated and NEMA 4X-rated, which means it can withstand harsh weather conditions, including rain, snow, and extreme temperatures. The built-in heater ensures consistent performance in cold environments, maintaining both functionality and image quality.

The camera is powered over Ethernet (PoE), facilitating easy installation with just one cable for both data and power. This simplifies the setup process and reduces additional wiring costs. Additionally, the Q6045-E supports various video compression formats, including H.264 and H.265, allowing for efficient bandwidth usage without compromising video quality.

In conclusion, Axis Communications Q6045-E is a feature-rich choice for any professional surveillance system, offering high-resolution video, intelligent analytics, robust durability, and flexible installation options. Its innovative technologies make it an ideal solution for enhancing security and surveillance efforts in a wide range of environments.