Kenmore 153.339210 HA Removing the Old Water Heater, Turn OFF the gas supply to Water Heater

Page 8

Removing the Old Water Heater

		FIGURE2.
(_) Turn "OFF" the gas supply to the
water	heater.
If the	main gas line shutoff valve
serving all gas appliances				is
used,	also shut "OFF" the gas at
each	appliance.	Leave	all	gas
appliances shut "OFF" until the
water	heater	installation		is
completed, see		Figures 2	and 3.		FIGURE&

(_) Turn "OFF" the water supply to the water heater at the water shut off

valve or water meter. Some installations require that the water be turned off to the entire house, see Figures 2 and 4.

FIGURE&

(_ Check again to make sure the gas supply is "OFF" to the water heater. Then disconnect the gas supply connection from the gas control valve.

Burn hazard

-Hot water discharge.

,Keep hands clear of drain valve discharge,

(_ Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearby hot water faucet which will relieve pressure in the water heater and speed draining. The water passing out of the drain valve may be extremely hot. To avoid being scalded, make sure all

	connections	are tight and that the
	water flow is directed away from		FIGURE5.
	any person,	see Figures 2 and 5.

(_Disconnect the vent pipe from the draft hood where it connects to the water heater. In most installations the vent pipe can be lifted off after any screw or other attached devices are removed. Dispose of the draft hood. The new water heater has a draft hood which must be used for proper operation.

If you have copper piping to the water heater, the two copper water pipes can be cut with a hacksaw approximately four inches away from where they connect to the water heater, see Figure 6. This will avoid cutting off pipes too short. Additional cuts can be made later if necessary, Disconnect the temperature-pressure relief valve drain line. When the water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now completely disconnected and ready to be removed.

FIGURE&

If you have galvanized pipes to the water heater, loosen the two galvanized pipes with a pipe wrench at the union in each line. Also disconnect the piping remaining to the water heater, see Figure 7. These pieces should be saved since they may

be needed when reconnecting the new water heater. Disconnect the temperature-pressure relief valve drain line. When the water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now completely disconnected and ready to be removed.

Mineral buildup or sediment may have accumulated in the old water heater. This causes the water heater to be much heavier than normal and this residue, if spilled out, could cause staining.

FIGURE7.

Image 8

Contents Installation and service must be Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ADo not store or use gasoline or other Model noSymbol indicates a potentially hazardous Indicates An imminentlyCould result in death or injury Death or injuryImproper installation and use may result Property damage Fire HazardExplosion Hazard Feel water before bathing or showeringPage Recovery DimensionsType Rategals DiameterWhen Sweat Soldering Materials NeededBasic Tools Additional Tools Needed You may or may not need all these tools, depending on yourAnode ManuaIGas Shut-off ValveThermostat Pilot & Main BurnerRemoving the Old Water Heater Turn OFF the gas supply to Water HeaterFire or ExpJosion Hazard Facts to Consider About LocationProperty Damage Hazard Insulation Blankets Ii ,iALL AIR from Inside Buildings FIGUREllWater Piping Hotter Water can ScaldTemperature-Pressure Relief Valve Water Damage HazardFilling the Water Heater VentingGas Piping Fire and Explosion HazardSediment Traps Ire and Explosion HazardGAS Piping with ALL Black Iron Pipe to GAS Control RreOso What to do if YOU Smell GASTemperature Regulation Tank Sediment Cleaning Burner Inspection Burner CleaningTemperature-Pressure Relief Valve Operation HousekeepingAnode Rod Inspection DrainingSee Figure Drain Valve Washer ReplacementService Inlet* Water Heater Capacity Ganons Pressure Start Up ConditionsThermal Expansion Makenecessaryairsupplychangestocorrect Operational ConditionsILII/I Leaking T&P Valve Page Page Burnerassembly Model Numbers Part DescriptionBy calling 1-800-366-PART 1-800-366-7278. If the parts you 153.339560 153.339760Information Page Full ONE Year Warranty on Water Heater Limited Warranty on Tanks That LeakLimited Warranty on Parts Sears Installation Service