Kenmore 153.33385 owner manual Materials and Basic Tools Needed, Materials Needed

Page 6

MATERIALS AND BASIC TOOLS NEEDED

Materials Needed

To simplify the installation Sears has available the installation parts shown below. You may or may not need all of these materials, depending on your type of installation.

EXPANSION TANKS FOR THERMAL EXPANSION CONDITIONS AVAILABLE IN 2 GALLONS

(7.6 LITERS) AND

5 GALLONS (18.9 LITERS) CAPACITY HROUGH LOCAL SEARS STORE OR SERVICE CENTER.

WATER HEATER INSTALLATION KIT WITH FLEXIBLE CONNECTORS FOR 3/4”

(19.05 mm) OR 1/2” (12.7 mm) THREADED OR COPPER PLUMBING AND FLEXIBLE WATER HEATER GAS CONNECTOR WITH FITTINGS.

DRAIN PANS AVAILABLE IN 20” (508 mm) DIAMETER FOR WATER HEATERS HAVING A DIAMETER 18” (457 mm) OR LESS, 24” (610mm) DIAMETER FOR WATER HEATERS HAVING A DIAMETER 22” (559 mm)

OR LESS AND AVAILABLE IN 28” (711 mm) DIAMETER FOR WATER HEATERS HAVING A DIAMETER 26” (660 mm) OR LESS.

Basic Tools

You may or may not need all these tools, depending on your type of installation. These tools can be purchased at your local Sears Store.

Pipe Wrenches (2) 14” (356 mm)

Screwdriver

Tin Snips

6’ (1.82 m) Tape or Folding Ruler

Garden Hose

Drill

Pipe Dope or Teflon Tape

DRILL

SLOT-HEAD SCREWDRIVER

TIN SNIPS

PHILLIPS SCREWDRIVER

 

PIPE DOPE

ROLL OF TEFLON

(SQUEEZE TUBE)

TAPE (USE ONLY ON

USE FOR WATER AND GAS

WATER CONNECTIONS)

CONNECTIONS

GARDEN HOSE

6 FOOT TAPE

PIPE WRENCH

Additional Tools Needed

When Sweat Soldering

Tubing Cutters or Hacksaw

Propane Tank

Soft Solder

Solder Flux

Emery Cloth

Wire Brushes

 

PROPANE

TUBING CUTTER

TORCH

 

ROLL OF

HACKSAW

EMERY CLOTH

3/4” (19 mm) WIRE BRUSH

 

 

 

ROLL OF LEAD-FREE

SOLDER

1/2” (13 mm) WIRE BRUSH

SOFT SOLDER

FLUX

6

Image 6
Contents Economizer GAS Water Heater Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents Product Specifications Preparing for the InstallationCustomer Responsibilities Materials and Basic Tools Needed Materials NeededRelief Install PERGET to Know Your Water Heater ALL Piping Materials to be Supplied by CustomersInstallation Instructions Removing the OLD Water HeaterTypical Installations Hotter Water can ScaldLocating the NEW Water Heater Facts to Consider about the LocationInsulation Blankets Installing the NEW Water Heater Securing Water Heater to Floor and Wall Water PipingValve and Pipe Insulation TEMPERATURE-PRESSURE Relief Valve Water Piping Pressure TestOr Property Damage Filling the Water Heater Draft Hood Installation VentingGAS Piping Sediment Traps Alternative Sediment Trap LocationPage Page Operating Instructions Installation Checklist Before Lighting the PilotTemperature Regulation SettingVenting System Inspection Service and AdjustmentBurner Cleaning Burner InspectionTEMPERATURE-PRESSURE Relief Valve Operation Anode ROD InspectionDraining Drain Valve Washer Replacement ServiceTroubleshooting Guide Start UP ConditionsOperational Conditions CondensationLeakage Checkpoints Troubleshooting Guidelines Burner Assembly Parts Order ListPage Warranty Service Year Limited Warranty on Water HeaterYear Exclusive Kenmore Labor Warranty Sears Installation Service