ADT Security Services Security Manager 2000 Testing the System, Using the Test Key, 27 Ð

Page 27

Ê Ê 5 Ê Ê

Using the TEST Key

TESTING THE SYSTEM

(TO BE CONDUCTED WEEKLY)

The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation. The touchpad sounds a single beep every 40 seconds as a reminder that the system is in the Test mode.

N o t e : An alarm message will not be sent to your Customer Care Center during the following tests.

1.DISARM THE SYSTEM. Disarm the system and close all protected windows, doors, etc. The READY indicator light should come on if all zones are intact (i.e., all protected windows, doors, etc. are closed.

AC

*** DIS ARME D ***

RE ADY TO ARM

ENGLISH DISPLAY TOUCHPAD

TEST

2. ÊÊÊ ÊÊÊ ÊÊÊ ÊÊÊ + ÊÊÊ5ÊÊÊ

(Security Code)

CUSTOM DISPLAY TOUCHPAD

ÊEnter the security code, then press TEST key.

Example: Ê 7 Ê Ê 2 Ê Ê 9 Ê Ê 6 Ê then press the TEST key.

3.Listen. The external sounder should sound for 1 second and then turn off. If the sounder does not sound, CALL FOR SERVICE IMMEDIATELY.

4.Fault zones. Open each protected door and window in turn and listen for three beeps from the touchpad. Identification of each faulted protection point should appear on the display. The display will clear when the door or window is closed.

(Continued)

Ð 27 Ð

Image 27

Contents Security System About This Manual Table of Contents General Partitioned System System OverviewSystem Overview Single-Button Paging ENTRY/EXIT Delays General InformationPartition ENTRY/EXIT Delays Exit AlarmsCommon Zone Operation About the Touchpads 10 Ð About the Touchpads11 Ð Functions of the TouchpadsEnglish Display Touchpad Custom English Display Touchpad12 Ð Using the Ready Key Checking for Open Zones13 Ð Arming Perimeter only With Entry Delay on Using 3 Ê Stay Key14 Ð Arming Perimeter only With Entry Delay OFF Instant Key15 Ð 16 Ð Arming ALL Protection With Entry Delay onUsing 2 Ê Êaway Key Use this key when no one will be staying insideDisarming and Silencing Alarms Using 1 Ê Êoff Key17 Ð Using 6 Ê Bypass Key Bypassing Protection Zones18 Ð 19 Ð Bypassing Protection ZonesTo turn Chime Mode off Chime ModeUsing 9 Ê Êchime Key To turn Chime Mode on21 Ð For Manually Activating Silent AND/OR Audible AlarmsUsing Panic Keys Panic KeysManually Initiating a Fire Alarm Verify this with your installer22 Ð Using Device Commands Enter Security Code then Press # + 7 + Device NumberEnter Security Code then Press # + 8 + Device Number 24 Ð Paging FeatureSecurity Codes Duress Code Quick Arming Single-Button25 Ð Security Codes 27 Ð Testing the SystemUsing the Test Key ÊEnter the security code, then press Test key28 Ð Exit Test ModeCheck and Battery Displays Trouble Conditions29 Ð Modem Comm Trouble ConditionsCOMM. Failure System LO BATLong Rng Trbl Total Power Failure Busy-StandbyDisabled. Call for Service Immediately Open CircuitMaintaining Your System 33 Ð Maintaining Your System34 Ð Quick Guide to System Functions35 Ð Summary of AUDIBLE/VISUAL Notifications36 Ð Summary of AUDIBLE/VISIBLE Notifications37 Ð UL Notice This is a Grade a Residential System38 Ð Federal Communications Commission FCC Part 68 Statement39 Ð Avis40 Ð Limitations of this Alarm System41 Ð Limitations of this Alarm System42 Ð Limited Warranty43 Ð InstallationÀN7527-6V2Dä