Harman Stove Company 828i manual Monitoring the GAS Flame, HOW to Light the Fire

Page 11

Swing-out Label with lighting instructions

Flame Adjustment Levers

11

Pilot Flames as Seen

Through Hole in Left End

of Log

Use a glove to avoid contact if hot. For best results when fine-tuning the flame picture, initially leave the middle lever unchanged from its factory set- ting. Move the other two levers as needed to increase or decrease the brightness and length of the flame: moving left will increase the flame; moving right will decrease the flame.

MONITORING THE GAS FLAME

Periodically, the flames of the Clarity Fireplace Insert should be checked while it is in operation. The flames should be well-defined and stable. They should be bright yellow with a blue base where attached to the burner ports. The flames should not look orange or sooty. Portions of the logs will glow red when the flames are properly adjusted.

If you find the flames to be other than that described here, do not operate the heater. Consult a qualified service person or your Harman dealer for advice.

Operation

HOW TO LIGHT THE FIRE

1.STOP! Read the safety information on the lighting instructions label on the stove.

2.If using the optional thermostat, set thermo- stat to the lowest setting.

3.Turn off electric power to the appliance.

4.Turn the ON-OFF/THERMOSTAT switch to the OFF position.

5.Push in the gas control knob slightly and turn it clockwise to "OFF."

NOTE: The knob cannot be turned from "PILOT" to "OFF" unless it is pushed in slightly. Do not force it.

6.Wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Follow "B" in the safety information on the swing-out label. If you don't smell gas, go to the next step.

7.Set the High-Low Regulator to High by turning it fully counterclockwise.

8.Press in the gas control knob slightly and turn counterclockwise to "PILOT."

9.Find the pilot by looking through the round opening on the left end of the center log.

10.Push the control knob fully down and hold. Immediately push the red piezo ignitor button to light the pilot. It is normal to have to push the red button several times before the pilot ignites. Con- tinue to hold the control knob in for about one (1) minute after the pilot is lit. Release the knob and it

will pop back up. Pilot should remain lit. If it goes

out, repeat steps 5 through 9.

•If the knob does not pop up when released, stop and immediately call your service technician

or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier.

11.Turn the gas control knob counterclock- wise to "ON."

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Harman Clarity 828i Gas Fireplace Insert Page Table of Contents Introduction .2 Gas Appliance Installation CodeClearances InstallationTest for Flue Spillage Connecting the Clarity FireplaceVenting Removing the Glass door AssemblyInsert to a GAS Supply Natural PropaneInstalling the Insert Connecting the CordsetConnecting Optional Thermostat Into the Fireplace AIR Shutter AdjustmentMonitoring the GAS Flame HOW to Light the FireInspecting the Venting MaintenanceRemoving the Glass Door Trim Panels Replacing the GasketConvection Blower Service Access Cleaning the GlassCleaning the LOG SET and Firebox Page Conversion KIT Components Appendix a Fuel ConversionAppendix B De-rating for High Altitude Appendix C Changing Orifices Appendix D Low Voltage Wiring Diagram Volt Wiring Diagram Parts List Burner Assembly Page Minimum Clearances from Combustible Construction SpecificationsNatural GAS Propane Year Limited Warranty Commercial

828i specifications

Harman Stove Company has long been a respected name in the realm of heating solutions, and their 828i model is no exception. This innovative pellet stove embodies the perfect blend of technology, efficiency, and aesthetic appeal.

The Harman 828i features a sleek design, making it suitable for various home decors while providing optimal heating performance. With a heat output of up to 68,000 BTUs, it can effectively warm spaces ranging from 1,500 to 3,000 square feet, making it ideal for both residential and commercial applications. One of the most appreciated features of the 828i is its large hopper capacity, capable of holding up to 50 pounds of pellets. This translates to extended burn times and less frequent refueling, which is convenient for users.

One standout technology in the 828i is the Smart Control panel, which facilitates easy operation and allows users to program their heating preferences. With this advanced control system, users can set different heating schedules, maximizing comfort and efficiency while minimizing fuel consumption. Additionally, the stove is equipped with an intelligent temperature sensor that helps maintain a consistent temperature, further enhancing its efficiency.

The 828i also boasts a unique heat exchanger design that promotes superior heat transfer while minimizing emissions. Harman has incorporated their signature Emission-Reduction Technology, which ensures that the stove operates with a low environmental impact. This commitment to sustainability is evident in the high-efficiency ratings the stove achieves, often exceeding 80%.

For those who prioritize easy maintenance, the 828i is designed with user-friendly access for cleaning and service. The removable ash pan makes ash disposal straightforward, while the self-maintaining features of the stove reduce the need for frequent cleaning.

Overall, the Harman Stove Company 828i stands out in the crowded pellet stove market with its efficient heating capabilities, advanced technology, and thoughtful design. Whether for a cozy home or a larger commercial space, the 828i promises reliable warmth and impressive performance, making it a worthy investment for any heating needs. Its combination of modern aesthetics and cutting-edge function means it fits seamlessly into any environment while delivering the quality and reliability that Harman is known for.
Top Page Image Contents