Harman Stove Company 828i manual Assembly, Removing the Glass door

Page 7

Assembly

The Clarity 828I Fireplace Insert comes with the log set packed inside the firebox. The three trim panels and two wing brackets are packed together in a separate carton. NOTE: The wing brackets must go on before the door.

Left Wing

Bracket

Right Wing

Bracket

A second shipping carton contains the wing panels. Two different size wing panel sets are available for the Clarity Insert: large (32-1/2" X 44"), and small (30" X 40"). The set that will work best with the fireplace opening should be used. The wing panels may be trimmed to fit inside the fireplace opening if a flush look is desired.

Before the unit is installed, all components should be unpacked. The cross log must be re- moved, the packing material taken out, and then re-installed.

The Clarity 828I is shipped from the factory equipped to burn either natural gas or propane. If the alternate fuel is to be used, the appropriate burner system module must be installed at this time as well. See the fuel conversion instructions in Appendix A on page 15.

Removing the Glass door

NOTE: The glass door is heavy. Be prepared for its weight when lifting it to avoid damage during removal.

Locate latches on each side of the glass door. Then, grasp each latch handle and pull forward until the front is disengaged. Lift the glass door

7

slightly and remove it

Latch

from the stove. Set the

glass door aside in a

 

safe place where it

 

will not be damaged.

 

WARNING: Do not

 

abuse the glass on the

 

Clarity Fireplace

 

Insert front by strik-

 

ing, slamming, or

 

similar trauma. Do

 

not operate this

 

Fireplace Insert with

 

the glass panel re-

 

moved, cracked or

 

broken. Use only glass

 

supplied by Harman and approved for use with

 

this heater. Do not use substitute materials. Re-

 

placement of the panel should be done by a li-

 

censed or qualified service person.

 

Removing and Replacing logs

The log set consists of a back log (1), a center log that has a pilot-viewing port in the left end (2), ember strip (3), and a cross log that rests on top

(4).

4

1

2

3

Remove the cross log, the center log, and the ember strips, in that order. To remove the rear log, first pull the fuel system module forward about an inch to create clearance, then lift the log out.

Re-install the logs in the same order that they were removed. Place the rear log in position first, centered and pushed snugly against the back wall, and slide the fuel system module back into posi- tion.

Re-install the ember strips so that they rest against the front of the firebox. Guide them to- ward you and to the outside until they fit snugly. Check the air slot in the inside of the ember strips to confirm that they do not obstruct it.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Harman Clarity 828i Gas Fireplace Insert Page Table of Contents Introduction .2 Gas Appliance Installation CodeClearances InstallationVenting Connecting the Clarity FireplaceTest for Flue Spillage Removing the Glass door AssemblyInsert to a GAS Supply Natural PropaneConnecting Optional Thermostat Connecting the CordsetInstalling the Insert Into the Fireplace AIR Shutter AdjustmentMonitoring the GAS Flame HOW to Light the FireInspecting the Venting MaintenanceRemoving the Glass Door Trim Panels Replacing the GasketCleaning the LOG SET and Firebox Cleaning the GlassConvection Blower Service Access Page Conversion KIT Components Appendix a Fuel ConversionAppendix B De-rating for High Altitude Appendix C Changing Orifices Appendix D Low Voltage Wiring Diagram Volt Wiring Diagram Parts List Burner Assembly Page Natural GAS Propane SpecificationsMinimum Clearances from Combustible Construction Year Limited Warranty Commercial

828i specifications

Harman Stove Company has long been a respected name in the realm of heating solutions, and their 828i model is no exception. This innovative pellet stove embodies the perfect blend of technology, efficiency, and aesthetic appeal.

The Harman 828i features a sleek design, making it suitable for various home decors while providing optimal heating performance. With a heat output of up to 68,000 BTUs, it can effectively warm spaces ranging from 1,500 to 3,000 square feet, making it ideal for both residential and commercial applications. One of the most appreciated features of the 828i is its large hopper capacity, capable of holding up to 50 pounds of pellets. This translates to extended burn times and less frequent refueling, which is convenient for users.

One standout technology in the 828i is the Smart Control panel, which facilitates easy operation and allows users to program their heating preferences. With this advanced control system, users can set different heating schedules, maximizing comfort and efficiency while minimizing fuel consumption. Additionally, the stove is equipped with an intelligent temperature sensor that helps maintain a consistent temperature, further enhancing its efficiency.

The 828i also boasts a unique heat exchanger design that promotes superior heat transfer while minimizing emissions. Harman has incorporated their signature Emission-Reduction Technology, which ensures that the stove operates with a low environmental impact. This commitment to sustainability is evident in the high-efficiency ratings the stove achieves, often exceeding 80%.

For those who prioritize easy maintenance, the 828i is designed with user-friendly access for cleaning and service. The removable ash pan makes ash disposal straightforward, while the self-maintaining features of the stove reduce the need for frequent cleaning.

Overall, the Harman Stove Company 828i stands out in the crowded pellet stove market with its efficient heating capabilities, advanced technology, and thoughtful design. Whether for a cozy home or a larger commercial space, the 828i promises reliable warmth and impressive performance, making it a worthy investment for any heating needs. Its combination of modern aesthetics and cutting-edge function means it fits seamlessly into any environment while delivering the quality and reliability that Harman is known for.
Top Page Image Contents