Harman Stove Company 828i manual Natural Propane, Insert to a GAS Supply

Page 8

Log Positions When Assembled

Install the center log so that it goes all the way to the back and is centered. When properly posi- tioned, there should be an even gap along the front of the center burner in the cavity in the log. A small portion of the log support frame will be revealed. The center log has a round viewing port in the left end through which the pilot can be observed.

Install the cross log, making sure that it is ori- ented with the forked end toward the left rear of the stove, and slip it over the front locator pin and position as shown below.

Re-install and Secure the Glass door

NOTE: The glass door is heavy. Lift it carefully to prevent damage. Center the glass on the opening and suspend it in place by placing the tab hooks over the top edge of the opening. Press the glass slightly against the stove to confirm that it seats properly, then press it firmly against the front while pushing the levers to the rear to engage them.

8

INSERT TO A GAS SUPPLY

Burn Only the Fuel for Which the Heater is Equipped The Clarity Fireplace Insert will burn either natural gas or propane, but requires a dedicated burner system module for either fuel. The label on

the burner system module indicates the fuel for which it is equipped.

Making The Connection

NATURAL

PROPANE

The gas inlet is located at the bottom right rear of

the Insert. The inlet fitting

 

is a 1/4" male pipe

 

thread.

 

A separate gas shut-off

 

valve and a 1/8" N.P.T.

 

plugged tapping should

 

be installed immediately

 

upstream of the connec-

Inlet

tion to the appliance.

 

The ClarityFireplace

 

Insert must be discon-

 

nected from the gas supply piping during any pressure testing of that system at pressures in excess of 1/2 psig (3.5 kPa).

The Clarity gas control valve must be in the OFF position during any pressure testing of the gas supply system at pressures equal to or less than 1/2 psig (3.5 kPa).

WARNING: To avoid pipe compounds from entering into the gas train, apply compounds only to the male pipe threads and only to the first two threads.

CAUTION: TEST ALL JOINTS FOR LEAKS

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Harman Clarity 828i Gas Fireplace Insert Page Table of Contents .2 Gas Appliance Installation Code IntroductionInstallation ClearancesTest for Flue Spillage Connecting the Clarity FireplaceVenting Assembly Removing the Glass doorNatural Propane Insert to a GAS SupplyInstalling the Insert Connecting the CordsetConnecting Optional Thermostat AIR Shutter Adjustment Into the FireplaceHOW to Light the Fire Monitoring the GAS FlameMaintenance Removing the Glass Door Trim PanelsReplacing the Gasket Inspecting the VentingConvection Blower Service Access Cleaning the GlassCleaning the LOG SET and Firebox Page Appendix a Fuel Conversion Conversion KIT ComponentsAppendix B De-rating for High Altitude Appendix C Changing Orifices Appendix D Low Voltage Wiring Diagram Volt Wiring Diagram Parts List Burner Assembly Page Minimum Clearances from Combustible Construction SpecificationsNatural GAS Propane Year Limited Warranty Commercial

828i specifications

Harman Stove Company has long been a respected name in the realm of heating solutions, and their 828i model is no exception. This innovative pellet stove embodies the perfect blend of technology, efficiency, and aesthetic appeal.

The Harman 828i features a sleek design, making it suitable for various home decors while providing optimal heating performance. With a heat output of up to 68,000 BTUs, it can effectively warm spaces ranging from 1,500 to 3,000 square feet, making it ideal for both residential and commercial applications. One of the most appreciated features of the 828i is its large hopper capacity, capable of holding up to 50 pounds of pellets. This translates to extended burn times and less frequent refueling, which is convenient for users.

One standout technology in the 828i is the Smart Control panel, which facilitates easy operation and allows users to program their heating preferences. With this advanced control system, users can set different heating schedules, maximizing comfort and efficiency while minimizing fuel consumption. Additionally, the stove is equipped with an intelligent temperature sensor that helps maintain a consistent temperature, further enhancing its efficiency.

The 828i also boasts a unique heat exchanger design that promotes superior heat transfer while minimizing emissions. Harman has incorporated their signature Emission-Reduction Technology, which ensures that the stove operates with a low environmental impact. This commitment to sustainability is evident in the high-efficiency ratings the stove achieves, often exceeding 80%.

For those who prioritize easy maintenance, the 828i is designed with user-friendly access for cleaning and service. The removable ash pan makes ash disposal straightforward, while the self-maintaining features of the stove reduce the need for frequent cleaning.

Overall, the Harman Stove Company 828i stands out in the crowded pellet stove market with its efficient heating capabilities, advanced technology, and thoughtful design. Whether for a cozy home or a larger commercial space, the 828i promises reliable warmth and impressive performance, making it a worthy investment for any heating needs. Its combination of modern aesthetics and cutting-edge function means it fits seamlessly into any environment while delivering the quality and reliability that Harman is known for.
Top Page Image Contents