Heat & Glo LifeStyle PALOMA-BZ-MOD owner manual Top to Rear Vent Conversion

Page 33

E. Top to Rear Vent Conversion

Kit Contents: Top cover (no hole); Back panel (with hole).

Tools Required: Power drill; #2 Phillips bit; 5/32 in. (4 mm) Allen wrench; 5/8 in. (16 mm) open end wrench; high-temp silicone sealant (optional).

1.Remove the front door assembly by lifting it off of the spring-loaded latches on top of the appliance. Remove the inner glass door by disengaging the spring-loaded latches at the bottom of the appliance and lifting it off of the two spring loaded latches at the top of the appli- ance.

2.Remove the top plate with hole and discard. (Figure 8.7).

INNER EXTENSION COLLAR

DV ADAPTER

Figure 8.9

6. Remove the four screws from the cover plate on rear of appliance. Retain cover plate, gasket and screws. (see Figure 8.10).

Figure 8.7

3.Remove and retain the Allen head screws that hold the solid back panel in place. (Figure 8.8) Remove and

discard the solid back panel.

Figure 8.10

ALLENHEAD SCREWS

Figure 8.8

4.Remove the four screws from the DV adapter collar. (Figure 8.9) Set aside DV adapter collar, gasket and screws.

5.Remove the inner extension starter collar (Shown in Figure 8.9) and set aside.

7.Install the outer collar with gasket to the rear of appli- ance with screws previously removed. Install the inner extension starter collar. (Figure 8.11).

8.Install the new back panel (with hole) to the rear of appliance. Replace the allen head screws removed in Step 3 to hold the back panel in place. (Figure 8.11).

Figure 8.11

 

Heat & Glo • PALOMA-BZ-MOD, PALOMA-GR-MOD, PALOMA-GY-MOD • 2189-900 Rev. i • 5/12

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents What to do if you smell gas ModelsHomeowner Reference Information CongratulationsTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsGetting Started Design and Installation ConsiderationsTools and Supplies Needed Inspect Appliance and ComponentsSelecting Appliance Location Framing and ClearancesIt is permissible to place the appliance on carpet Clearances to CombustiblesVent Termination Minimum Clearances Termination LocationsAlcove Applications Venting Components Vent InformationUse of Elbows Measuring StandardsVenting Guidelines How to Use the Vent GraphAdding Venting Components Horizontal Termination203 mm 178 mm 152 mm Fold Strap Vertical Termination Continue to assemble pipe sections until the height Twist-lock the vent cap and seal Secure the Vent SectionsCathedral Ceiling Disassemble Vent SectionsClass a Metal Chimney Type a Existing Masonry ChimneyTo determine the length of flex needed, measure from Opening in Masonry Wall Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleAssembling Slim Line Trim Ring and Heat Shield FIG. C Minimum Clearance Gas Information Fuel ConversionGas Pressures Check for GAS Leaks Gas ConnectionConnecting to the Appliance Recommendation for WireIntelliFire Ignition System Wiring Wire Size Max. LengthLoss of Power and Battery Backup Usage Junction Box Wired to Wall Switch Wall Switch Installation for Fan OptionalAppliance Setup Remove Shipping MaterialsUnbolting Appliance from the Pallet Leveling and Lagging Down the Appliance AccessoriesTop to Rear Vent Conversion Shutter Adjustment Installing the Vent RestrictorAir Shutter Settings Installation Installing Rock Media and Ember MaterialLeft Rock Cluster Optional Blower Installation precautionsFAN Base Contacts FAN Bracket 28 Blower Wiring Diagram Recommended operating proceduresRemote Controls Installing flame control solenoidRemote receiver RED Wiring the flame control solenoidInner Glass Door Assembly Replacement Front Door Glass Assembly ReplacementOperating Instructions Before Lighting ApplianceControls Final inspection by Lighting Instructions IPIFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Ignition System Ues to spark, and main Before servicing Maintaining and Servicing ApplianceInspect Maintenance Tasks Maintenance TasksAppliance Dimension Diagram Reference MaterialsHearth Pad SLP Series Vent Components Vent Components DiagramComponents Vent Components ListRock Placement Service PartsPart number list on following Service Parts List StockedAt Depot #22 Bottom Plate Assembly NGK-DXV Limited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Contact Information

PALOMA-BZ-MOD specifications

The Heat & Glo LifeStyle PALOMA-BZ-MOD is an innovative and stylish gas fireplace designed to elevate the ambiance of any living space. This modern fireplace combines functionality, aesthetics, and advanced technology, making it an ideal choice for homeowners seeking both warmth and sophistication.

One of the standout features of the PALOMA-BZ-MOD is its contemporary design. With its clean lines and minimalist profile, this fireplace seamlessly integrates into various interior styles—from ultra-modern to classic decor. The wide viewing area provided by the expansive glass front ensures that the mesmerizing flames are the focal point of any room, creating an inviting and cozy atmosphere.

The PALOMA-BZ-MOD incorporates advanced heating technologies that enhance efficiency and performance. Its powerful heating capacity can warm spaces effectively, allowing for comfortable living even in colder climates. The unit is designed to operate quietly, ensuring that the crackling flames are the only sound you hear. This makes it perfect for homes where relaxation and tranquility are priorities.

Another noteworthy aspect of the PALOMA-BZ-MOD is its customizable features. Homeowners can choose from a variety of decorative media options, including ceramic logs, glass beads, or pebbles, allowing for personalization that complements individual style preferences. The flame presentation is adjustable, giving users control over the height and intensity of the flames, thus enhancing both aesthetics and functionality.

The fireplace is equipped with innovative technologies for ease of use. The flexible installation options mean it can be placed in a variety of locations, whether it's a central feature in a living room or an elegant addition to a dining area. Additionally, a user-friendly remote control allows for convenient operation, enabling users to turn the fireplace on or off and adjust settings from across the room.

Safety is a priority with the PALOMA-BZ-MOD. It features an advanced safety shut-off system, ensuring peace of mind for homeowners. The continuous pilot light and electronic ignition system enhance reliability, providing instant warmth when needed.

In summary, the Heat & Glo LifeStyle PALOMA-BZ-MOD exemplifies a harmonious blend of modern design and advanced technology. With its captivating flames, customizable features, and efficient heating performance, it serves as both a functional heating solution and a stunning piece of decor, making it a popular choice for any contemporary home.
Top Page Image Contents