Heat & Glo LifeStyle 6100PLUS Appliance Setup, Remove the Shipping Materials, Clean the Appliance

Page 21

10 Appliance Setup

A. Remove the Shipping Materials

Remove shipping materials from inside or underneath the ﬁ rebox.

WARNING

Shock Risk

Fire Risk

Use ONLY optional accessories approved for this appliance.

•Using non-listed accessories voids warranty.

•Using non-listed accessories may result in a safety hazard.

•Only Hearth & Home Technologies approved accessories may be used safely.

WARNING

Explosion Risk

•Follow rockwool placement instructions in this manual.

•Do NOT place rockwool directly over burner ports.

•Replace rockwool material annually.

Improperly placed rockwool interferes with proper burner operation.

B. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated in- side the ﬁ rebox or underneath in the control cavity.

•The appliance is shipped with the burner in place with the boxed up log set sitting on it. See Figure 10.1. Remove box.

•The refractory is not shipped with the appliance. The refractory must be ordered separately. Install the refractory following the installation instructions supplied with the kit.

•The grate is shipped on top of the appliance. See Figure 10.2. Remove the grate.

C. Lava Rock, Rockwool, Silica Rock Placement

Placing the Lava Rock

•Place the lava rock generously around the ember bed and up to the front lip of the hearth pan. You do not need ot use the whole bag; save the remaining amount for future use.

Figure 10.1 /Boxed Logs

Figure 10.3 Placing the Lava Rock

Figure 10.2 Shipping Location of Grate

Hearth & Home Technologies • 6100PLUS • 4041-127 Rev D • 09/05

21

Image 21

Contents What to do if you smell gas Models 6100PLUS Fresh Air FireplaceListing Label Information/Location Homeowner Reference InformationTable of Contents Listing and Code Approvals High Altitude InstallationsAppliance Certiﬁcation Non-Combustible MaterialsGetting Started Design and Installation ConsiderationsTools and Supplies Needed Inspect the Appliance and ComponentsFraming and Clearances Select Appliance LocationFire Risk Fire Risk Odor Risk Construct the Appliance ChaseMantel Projections ClearancesTermination Locations Vent Termination Minimum ClearancesFire Risk Explosion Risk Fire Risk Fumes Risk Vent Information and DiagramsSecuring and Leveling the Appliance Appliance PreparationFuel Conversion Gas Connection Gas InformationGas Pressure Gas Leak RiskFire Risk Explosion Risk Asphyxiation Risk Connecting to the Appliance Recommendation for WireElectrical Information Shock Risk Explosion Risk6100PLUS Requirements System WiringBetween R2 HRV200PLUS Control WiringAppliance Circuit Board Wiring Optional Accessories Requirements Wall SwitchFlame On/Off Electric Embers On/OffJunction Box Detail Junction Box InstallationFacing Material FinishingClean the Appliance Appliance SetupLava Rock, Rockwool, Silica Rock Placement Remove the Shipping MaterialsPlacing the Silica Rock Techno Sil Placing the Rock WoolPlace the Grate Grate and Log AssemblyPlace the Right Front Log Place the Top LogOperating Instructions Appliance ModeSequence of Operation Fire Risk Burn RiskHRV200PLUS Defrost Mode Lighting the Appliance Initial Break-in Procedure Fire Risk High TemperaturesAfter the Appliance is Lit Troubleshooting Guide TroubleshootingEmber Bed Bulb Replacement Annual MaintenanceCleaning the Burner and Control Compartment Maintaining and Servicing the ApplianceThis page intentionally left blank Reference Materials Appliance Dimension Diagram6100PLUS Service Parts ListLog Set Refractory Assembly, Traditional6100PLUS 6100PLUS-LP Description of Part 6100PLUSOptional Components Remote Control Wall SwitchSpfl Spvn Spwd SpwvOptional Components 6100PLUS 6100PLUS-LP Qty Arched Cabinet Doors Essence SeriesArched Cabinet Doors Prism Series This page intentionally left blank Limited Lifetime Warranty Contact Information