White Rodgers 1F92W-51 manual Lockout Bypass Option, Compressor Short Term Cycle Protection, Press

Page 21

LOCKOUT BYPASS OPTION

!CAUTION

FOR QUALIFIED SERVICE TECHNICIANS’ USE ONLY. OPERATORS SHOULD NOT USE THIS FEATURE DUE TO POSSIBILITY OF EQUIPMENT OR PROPERTY DAMAGE, OR PERSONAL INJURY.

DO NOT USE THE LOCKOUT BYPASS OP- TION UNLESS THE COMPRESSOR OIL HEATERS HAVE BEEN OPERATIONAL FOR 6 HOURS AND THE SYSTEM HAS NOT BEEN OPERATIONAL FOR AT LEAST 5 MINUTES.

COMPRESSOR LONG TERM CYCLE

PROTECTION

To protect the compressor from potential damage due to temperature change of crankcase oil, this thermostat has a built-in time delay of one hour less

than the power loss to the unit (up to 12 hours maximum lockout). During this time, auxiliary heat will be used when necessary to maintain setpoint temperature. DO NOT attempt to override this delay feature before crankcase temperature has stabi- lized (for example, if power has been out for three hours, the compressor should remain locked out for two hours).

COMPRESSOR SHORT TERM CYCLE

PROTECTION

This thermostat has a built-in short term (5-minute) time delay. During this 5-minute period, the thermo- stat will lock out the compressor to allow head pressure to stabilize. If you want to override this feature while testing thermostat operation, simply

press

ADV

and

HOLD

at the same time at initial

PRGM

TEMP

startup.

21

Image 21
Contents 1F92W-51 About Your New Thermostat Your NEW THERMOSTAT’S THERMOSTAT’S Specifications Installing Your ThermostatOperating Your Thermostat Programming YourYour NEW THERMOSTAT’S Features Precautions Accessories THERMOSTAT’S SpecificationsElectrical Data Thermal Data Staging DataInstalling Your Thermostat NEW InstallationRoute Wires to Location Routing thermostat wires Wire Identification Labels Replacement InstallationRemove OLD Thermostat WallPage Attach Subbase to Wall Subbase Typical wiring diagram for single transformer systems Depending on System Require Heat Pump System Attach Thermostat to Subbase USETo Turn Thermostat OFF be System Configuration SET Option SwitchesTwo Compressor Split System Switch #1 on Switch #2 on FAN Operation Check Thermostat OperationHeating System Operation Ming Your ThermostatCooling System Operation Lockout Bypass Option Compressor Short Term Cycle ProtectionPress Use System to turn the thermostat OFF Operating Your ThermostatBack of the Thermostat Body Parts of the ThermostatAting Features Removing thermostat from the wall to re- place the batteryUse To turn thermostat OFF beforeSystem Time SET View Hold Used with Thermostat Buttons and LightsSystem Time SET View Hold Operating Features Automatic Changeover on Automatic Changeover OFF TWO Hour Temperature OverrideTo adjust Heat anticipation, press Convertibility Press TimeTo increase the cycle time. If the heat Compressor Short Cycle Protec LOW Battery Indicator The word BATCool Cool or HeatUntil FAN Planning for Your Needs Programming Your ThermostatYour Home Your needs, simply press Factory preset programEntering Your Program Programming. be Sure to PressTurn Thermostat OFF Before REATTACH- ING to Subbase Weekday 5 DAY Weekend 2 DAY Heating/Cooling Schedule PlanMOR Heat SamplePress and hold either Set Current Time and DayUntil you Enter Heating ProgramWant to stop programming at any time, simply press Fore Reattaching to Subbase Enter Cooling ProgramCheck Your Programming Until you return to the point where you Questions and AnswersHow can I permanently change a part of my program? Gramming Your ThermostatWhat can cause the thermostat display to freeze or go blank? Why can’t I program the thermostat in the Auto mode?Mostat ING Your ThermostatErating Your Thermostat Why is the system turning on and off so frequently seldom? Maintains programming, press System until Page Page Part No -5414A