White Rodgers 1F92W-51 manual Compressor Short Cycle Protec, Cool or Heat

Page 32

cycles are too long, press

TIME

to decrease

continuously (non-flashing), 24 VAC power is

BACK

not being supplied and the thermostat is work-

the cycle time. To set COOL anticipation, press

ing on battery power only.

SET

and

SET

at the same time again. The

• COMPRESSOR SHORT CYCLE PROTEC-

CLOCK

DAY

display will show

COOL

14

(factory

TION — To protect your compressor from poten-

tial damage due to rapid cycling, this thermostat

preprogrammed

cooling anticipation). Use

has a built-in delay of 5 minutes between cooling

TIME

and

TIME

to adjust anticipation. To set

cycles. The following may cause a time delay in

FWD

BACK

AUXILIARY heat anticipation (not applicable to

COOL or HEAT:

a)

Return of power after a momentary power

multi-stage use), press

SET

and

SET

at the

outage.

CLOCK

DAY

same time again. The display will show AUX 8

b)

Pressing

SYSTEM

change operating

(factory preprogrammed auxiliary anticipation).

HEAT-OFF-COOL-AUTO to

Use

TIME

and

TIME

to adjust anticipation.

modes.

FWD

BACK

c)

Pressing

or

to create a call for

Press

RUN

to return to your program.

COOL or HEAT too soon after a previous

PRGM

	• LOW BATTERY INDICATOR — The word BAT	call.
		During lockout in the COOL mode, the blower
	will flash on the display if the battery is low and
		will operate, but compressor operation will be
	should be replaced. When BAT is displayed
		delayed.

32

Image 32

Contents 1F92W-51 About Your New Thermostat THERMOSTAT’S Specifications Installing Your Thermostat Your NEW THERMOSTAT’SOperating Your Thermostat Programming YourYour NEW THERMOSTAT’S Features Precautions THERMOSTAT’S Specifications AccessoriesElectrical Data Thermal Data Staging DataRoute Wires to Location Installing Your ThermostatNEW Installation Routing thermostat wires Replacement Installation Wire Identification LabelsRemove OLD Thermostat WallPage Attach Subbase to Wall Subbase Typical wiring diagram for single transformer systems Depending on System Require Heat Pump System To Turn Thermostat OFF be Attach Thermostat to SubbaseUSE Two Compressor Split System System ConfigurationSET Option Switches Switch #1 on Switch #2 on Check Thermostat Operation FAN OperationHeating System Operation Ming Your ThermostatCooling System Operation Press Lockout Bypass OptionCompressor Short Term Cycle Protection Operating Your Thermostat Use System to turn the thermostat OFFParts of the Thermostat Back of the Thermostat BodyRemoving thermostat from the wall to re- place the battery Ating FeaturesUse To turn thermostat OFF beforeSystem Time SET View Hold Thermostat Buttons and Lights Used withSystem Time SET View Hold Operating Features Automatic Changeover on TWO Hour Temperature Override Automatic Changeover OFFTo increase the cycle time. If the heat To adjust Heat anticipation, pressConvertibility Press Time LOW Battery Indicator The word BAT Compressor Short Cycle ProtecCool Cool or HeatUntil FAN Programming Your Thermostat Planning for Your NeedsYour Home Factory preset program Your needs, simply pressTurn Thermostat OFF Before REATTACH- ING to Subbase Entering Your ProgramProgramming. be Sure to Press Heating/Cooling Schedule Plan Weekday 5 DAY Weekend 2 DAYSample MOR HeatSet Current Time and Day Press and hold eitherUntil you Enter Heating ProgramWant to stop programming at any time, simply press Enter Cooling Program Fore Reattaching to SubbaseCheck Your Programming Questions and Answers Until you return to the point where youHow can I permanently change a part of my program? Gramming Your ThermostatWhy can’t I program the thermostat in the Auto mode? What can cause the thermostat display to freeze or go blank?ING Your Thermostat MostatErating Your Thermostat Why is the system turning on and off so frequently seldom? Maintains programming, press System until Page Page Part No -5414A