White Rodgers 1F92W-51 manual Convertibility Press Time, To adjust Heat anticipation, press

Page 31

gram. Press HOLDTEMP . HOLD will be displayed.

Then choose the desired hold temperature by

pressing or . The thermostat will hold the room temperature at the selected set-

ting until you press HOLDTEMP to start program op-

eration again. This feature is ideal for energy conservation when the building is unoccupied for an extended period of time.

• °F/°C CONVERTIBILITY — Press TIME and

FWD

TIME

BACK at the same time until the temperature

display is in °C (Celsius). To display °F, repeat the process.

•ADJUSTABLE HEATING AND COOLING CYCLE TIMES (ANTICIPATION) — If the heat- ing/cooling system is turning on and off too often (short cycles) or not often enough (long

cycles), you may want to adjust the anticipation setting.

!CAUTION

An anticipation setting of less than 10 may cause decreased compressor life.


To adjust HEAT anticipation, press		SET	and
To adjust HEAT anticipation, press		CLOCK	and
SET	at the same time. The display will show
DAY	at the same time. The display will show

HEAT 18. You may select any anticipation setting from 4 to 40 (note that for add-on heat pump systems, a minimum anticipation of 10 is recommended). When you adjust antici- pation, increase or decrease the displayed num- ber by only one or two digits, then let the system run for a while to see if the adjustment is sufficient. If the heat cycles are too short, press

TIME	to increase the cycle time. If the heat
FWD

31

Image 31

Contents 1F92W-51 About Your New Thermostat Programming Your THERMOSTAT’S Specifications Installing Your ThermostatYour NEW THERMOSTAT’S Operating Your ThermostatYour NEW THERMOSTAT’S Features Precautions Staging Data THERMOSTAT’S SpecificationsAccessories Electrical Data Thermal DataNEW Installation Installing Your ThermostatRoute Wires to Location Routing thermostat wires Wall Replacement InstallationWire Identification Labels Remove OLD ThermostatPage Attach Subbase to Wall Subbase Typical wiring diagram for single transformer systems Depending on System Require Heat Pump System USE Attach Thermostat to SubbaseTo Turn Thermostat OFF be SET Option Switches System ConfigurationTwo Compressor Split System Switch #1 on Switch #2 on Ming Your Thermostat Check Thermostat OperationFAN Operation Heating System OperationCooling System Operation Compressor Short Term Cycle Protection Lockout Bypass OptionPress Use System to turn the thermostat OFF Operating Your ThermostatBack of the Thermostat Body Parts of the ThermostatTo turn thermostat OFF before Removing thermostat from the wall to re- place the batteryAting Features UseSystem Time SET View Hold Used with Thermostat Buttons and LightsSystem Time SET View Hold Operating Features Automatic Changeover on Automatic Changeover OFF TWO Hour Temperature OverrideConvertibility Press Time To adjust Heat anticipation, pressTo increase the cycle time. If the heat Cool or Heat LOW Battery Indicator The word BATCompressor Short Cycle Protec CoolUntil FAN Planning for Your Needs Programming Your ThermostatYour Home Your needs, simply press Factory preset programProgramming. be Sure to Press Entering Your ProgramTurn Thermostat OFF Before REATTACH- ING to Subbase Weekday 5 DAY Weekend 2 DAY Heating/Cooling Schedule PlanMOR Heat SampleEnter Heating Program Set Current Time and DayPress and hold either Until youWant to stop programming at any time, simply press Fore Reattaching to Subbase Enter Cooling ProgramCheck Your Programming Gramming Your Thermostat Questions and AnswersUntil you return to the point where you How can I permanently change a part of my program?What can cause the thermostat display to freeze or go blank? Why can’t I program the thermostat in the Auto mode?Mostat ING Your ThermostatErating Your Thermostat Why is the system turning on and off so frequently seldom? Maintains programming, press System until Page Page Part No -5414A