White Rodgers 1F92W-51 manual Your needs, simply press, Factory preset program

Page 36

8a. What time does the last person go to bed at night?

b.What temperature should the house be at this time? These will be your NHT (night) tempera- ture settings.

Now look at the factory preprogrammed times and temperatures shown below. If this program will suit

your needs, simply press	RUN	to begin running the
your needs, simply press	PRGM	to begin running the
factory preset program.

If you want to change the preprogrammed times and temperatures, do the following.

NOTE

To operate properly in the AUTO mode, there must be a minimum 1°F separation between the highest heat temperature and the lowest cool temperature (see diagram below).

79	COOLING TEMPERATURES
78

77DEAD BAND 1°F

75HEATING TEMPERATURES

Determine the time periods and heating and cooling temperatures for your weekday program. You must program 4 periods for each day (MOR, DAY, EVE, and NHT). However, you may use the same heating

Heating Program for ALL days of the Week:

PERIOD	TIME	TEMP
MOR	5:00 AM	70
DAY	9:00 AM	70
EVE	4:00 PM	70
NHT	10:00 PM	64

Cooling Program for ALL Days of the Week:

PERIOD	TIME	TEMP
MOR	5:00 AM	78
DAY	9:00 AM	82
EVE	4:00 PM	78
NHT	10:00 PM	78

36

Image 36

Contents 1F92W-51 About Your New Thermostat THERMOSTAT’S Specifications Installing Your Thermostat Your NEW THERMOSTAT’SOperating Your Thermostat Programming YourYour NEW THERMOSTAT’S Features Precautions THERMOSTAT’S Specifications AccessoriesElectrical Data Thermal Data Staging DataInstalling Your Thermostat NEW InstallationRoute Wires to Location Routing thermostat wires Replacement Installation Wire Identification LabelsRemove OLD Thermostat WallPage Attach Subbase to Wall Subbase Typical wiring diagram for single transformer systems Depending on System Require Heat Pump System Attach Thermostat to Subbase USETo Turn Thermostat OFF be System Configuration SET Option SwitchesTwo Compressor Split System Switch #1 on Switch #2 on Check Thermostat Operation FAN OperationHeating System Operation Ming Your ThermostatCooling System Operation Lockout Bypass Option Compressor Short Term Cycle ProtectionPress Operating Your Thermostat Use System to turn the thermostat OFFParts of the Thermostat Back of the Thermostat BodyRemoving thermostat from the wall to re- place the battery Ating FeaturesUse To turn thermostat OFF beforeSystem Time SET View Hold Thermostat Buttons and Lights Used withSystem Time SET View Hold Operating Features Automatic Changeover on TWO Hour Temperature Override Automatic Changeover OFFTo adjust Heat anticipation, press Convertibility Press TimeTo increase the cycle time. If the heat LOW Battery Indicator The word BAT Compressor Short Cycle ProtecCool Cool or HeatUntil FAN Programming Your Thermostat Planning for Your NeedsYour Home Factory preset program Your needs, simply pressEntering Your Program Programming. be Sure to PressTurn Thermostat OFF Before REATTACH- ING to Subbase Heating/Cooling Schedule Plan Weekday 5 DAY Weekend 2 DAYSample MOR HeatSet Current Time and Day Press and hold eitherUntil you Enter Heating ProgramWant to stop programming at any time, simply press Enter Cooling Program Fore Reattaching to SubbaseCheck Your Programming Questions and Answers Until you return to the point where youHow can I permanently change a part of my program? Gramming Your ThermostatWhy can’t I program the thermostat in the Auto mode? What can cause the thermostat display to freeze or go blank?ING Your Thermostat MostatErating Your Thermostat Why is the system turning on and off so frequently seldom? Maintains programming, press System until Page Page Part No -5414A