Desa VGMRN, CGMFN, CGMFP Operating Fireplace, Optional Wall Switch GWMS2 Remote-Ready Models Only

Page 18

INSTALLATION

Continued

optional Wall SWITCH - GWMS2 (Remote-Ready Models Only)

WARNING: Read and fol- low installation instructions. Installation should be done by a qualified installer familiar with low-voltage wiring procedures.

WARNING: Do not connect this switch to any electrical source! Electrical shock and/or fire hazard will occur.

1.Connect one terminal of 25 ft. wire to “TPTH” terminal on control valve (see Fig- ure 23, page 17).

2.Connect remaining wire terminal to the “TH” terminal on the control valve. Make sure that wire terminals are in the positions on your unit as pictured in Figure 23, page 17. If wires are not “crossed” the thermostat will not work.

3.Route the 25 ft. wire to a convenient location to mount your wall switch (no outside walls).

WARNING: Do not connect the switch to a power source. Electrical shock and/or fire haz- ard will occur.

IMPORTANT: The wire may be shortened but must not be lengthened.

4.Connect one bare wire end to each of the terminals of the provided wall switch.

5.Install the wall switch and cover in the wall.

INSTALLING LOG SET AND SCREEN

1.Remove log packaging material and discard packaging. Gently place log over the burner (see Figure 26). Do not allow log to contact flame. If flame contacts log, soot will be created.

2.Reattach screen by placing the notches in the screen frame over the shoulder screws and pushing down.

Shoulder Screw

Log

Screen

Figure 26 - Installing Log and Screen

Operating Fireplace

MANUAL-Controlled

Models

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result causing property damage, per- sonal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service tech- nician or gas supplier. Force or attempted repair may result in a fire or explosion.

18

www.desatech.com

119315-01A

Image 18
Contents OWNER’S Operation and Installation Manual Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Local Codes UnpackingAssembly Product FeaturesOptional Remote Control Accessories Product IdentificationAir for Combustion Ventilation Providing Adequate VentilationConfined and Unconfined Space AIR for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location Determining if You Have a Confined or Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Installation ItemsCheck GAS Type Fireplace Clearances InstallationBuilt-In Fireplace Installation Fireplace pilot and burner must be at least 18 above floorMantel Clearances for Built-In Installation If you have not assembled firebox, follow instructions onRoute flexible gas line through access hole in hearth base Placing Hearth Base Against WallConnecting to GAS Supply Propane/LP Supply Tank External RegulatorPropane/LP Connecting Fireplace to Gas SupplyInstallation Items Needed NaturalChecking GAS Connections Test Pressures Equal To or Less Than Psig 3.5 kPaCorrect all leaks at once Installing Receiver Optional Wireless hand-held Remote Control AccessoriesPressure Testing Fireplace Gas Connections Installing 9-Volt Battery in Hand-Held Remote Control UnitMust not be lengthened See FigureAs pictured in Figure Air conditioning ductsFor Your Safety Read Before Lighting Optional Wall Switch GWMS2 Remote-Ready Models OnlyInstalling LOG SET and Screen Operating FireplaceOperating Fireplace Lighting InstructionsRemote-ready Models Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off FireplaceOptional Hand-Held Remote OperationOn/Off Series Model HRC100 and HRC101 Manual ModeAuto Thermostatic Mode Thermostat Series Model HRC200 and HRC201Pilot Flame Pattern Switch OptionalInspecting Burners Burner Flame PatternIf burner flame pattern is incorrect, as shown in Figure Cleaning MaintenanceBurner Injector Holder Pilot Air Inlet Hole Blow air into the primary air holes on the injector holderLOG Set TroubleshootingObserved Problem Possible Cause Remedy CabinetTroubleshooting Observe minimum installa Delayed ignition of burnerNoise when burner is lit White powder residue forming When heated, vapors fromGas leak. See Warning Replacement Parts SpecificationsWiring Diagram Service HintsIllustrated Parts Breakdown MANUAL-controlled models Cgmfn and CgmfpParts List 101629-02Illustrated Parts Breakdown REMOTE-READY Models Receiver and HAND-HELD Remote Control KIT HRC100 and HRC101 AccessoriesWALL-MOUNT ON/OFF Switch Equipment Shutoff Valve GA5010119315-01A Not a UPC

VGMRN, VGMRP, CGMFN, CGMFP specifications

Desa CGMFP, VGMRN, VGMRP, and CGMFN represent a series of cutting-edge developments designed to optimize various aspects of modern technology and infrastructure. These entities focus on enhancing efficiency, sustainability, and overall performance within their respective domains.

Desa CGMFP, or the Comprehensive Green Manufacturing Facility Program, is dedicated to promoting sustainable manufacturing practices. Its primary features involve the integration of green technologies that minimize waste and energy consumption. The program emphasizes the use of renewable energy sources, such as solar and wind, to power manufacturing operations. This initiative not only reduces the carbon footprint of production processes but also helps organizations meet regulatory standards for environmental protection.

VGMRN, which stands for Variable Grid Management and Resource Network, is a sophisticated system designed to enhance the efficiency of energy distribution. It utilizes advanced algorithms and machine learning to manage energy loads dynamically across the grid. One of the standout characteristics of VGMRN is its ability to forecast energy demand patterns, allowing for proactive adjustments to energy supply. This results in minimized downtime and optimized usage of resources, making it an essential component of smart grid solutions.

VGMRP, or Variable Grid Management and Resource Planning, complements the work of VGMRN by focusing on the strategic planning of resource allocation within energy networks. Its core features include predictive analytics and scenario modeling, which empower utilities to simulate various energy distribution scenarios and make informed decisions. This technological approach not only aids in efficient resource use but also supports resilience against fluctuations in energy supply and demand.

Lastly, CGMFN, the Comprehensive Green Manufacturing Framework Network, provides a robust platform for collaboration across industries engaged in green manufacturing. This network facilitates the sharing of best practices, research advancements, and innovative solutions. Key characteristics of CGMFN include a strong emphasis on interdisciplinary cooperation and the promotion of circular economy principles, which encourage the utilization of recycled materials and waste reduction strategies.

Together, these initiatives encapsulate a forward-thinking approach to manufacturing and energy management. They leverage technology and strategic planning to enhance productivity while ensuring that environmental sustainability remains at the forefront of operations. As industries continue to evolve, Desa CGMFP, VGMRN, VGMRP, and CGMFN will play pivotal roles in shaping a greener, more efficient future.