Desa CGMFP, CGMFN, VGMRN, VGMRP installation manual Optional Hand-Held, Remote Operation

Page 21

OPERATING FIREPLACE

Continued

4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, page 20. If you don’t smell gas, go to the next step.

5. Press in and turn control knob counter-

clockwise to the PILOT position. Press in control knob for five (5) seconds (see Figure 30, page 20).

Note: You may be running this fireplace for the first time after hooking up to gas sup- ply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system.

6. With control knob pressed in, press and hold electronic ignitor button. This will light pilot. The pilot is attached to the front of the burner. If needed, keep pressing ignitor button until pilot lights.

Note: If pilot does not stay lit, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

• If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 through 8.

8.Slightly push in and turn control knob coun-

terclockwise to the ON position.

Pilot

Ignitor

Burner

Electrode

 

Figure 31 - Propane/LP Gas Pilot

Pilot Burner

Ignitor

 

Electrode

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1. Turn control knob clockwise to the OFF position.

2. If Using Optional Hand-Held Remote: Set re- mote switch to the OFF position to prevent draining battery.

Shutting Off Burner Only (pilot stays lit) You may shut off the burner and keep the pilot lit by doing one of the following:

1.Turn control knob clockwise to the PILOT position.

2.If Using Optional Hand-Held Remote: Use remote control manual OFF button.

WARNING: Make sure remote sensorselectorswitchisintheOFF position when you are away from home for long periods of time.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 5 under Lighting Instructions, page 20.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 8 under Lighting Instructions, column 1.

optional Hand-Held

REMOTE OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, page 34). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions on page 20.

Figure 32 - Natural Gas Pilot

119315-01A

www.desatech.com

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory OWNER’S Operation and Installation ManualTable of Contents Safety Information Unpacking Local CodesOptional Remote Control Accessories Product FeaturesAssembly Product IdentificationProviding Adequate Ventilation Air for Combustion VentilationDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationConfined and Unconfined Space Determining if You Have a Confined or Unconfined SpaceVentilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Installation ItemsCheck GAS Type Built-In Fireplace Installation InstallationFireplace Clearances Fireplace pilot and burner must be at least 18 above floorIf you have not assembled firebox, follow instructions on Mantel Clearances for Built-In InstallationPlacing Hearth Base Against Wall Route flexible gas line through access hole in hearth basePropane/LP Supply Tank External Regulator Connecting to GAS SupplyInstallation Items Needed Connecting Fireplace to Gas SupplyPropane/LP NaturalChecking GAS Connections Test Pressures Equal To or Less Than Psig 3.5 kPaCorrect all leaks at once Pressure Testing Fireplace Gas Connections Optional Wireless hand-held Remote Control AccessoriesInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control UnitAs pictured in Figure See FigureMust not be lengthened Air conditioning ductsInstalling LOG SET and Screen Optional Wall Switch GWMS2 Remote-Ready Models OnlyFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions Operating FireplaceTo Turn OFF GAS To Appliance Manual Lighting ProcedureRemote-ready Models Shutting Off FireplaceRemote Operation Optional Hand-HeldAuto Thermostatic Mode Manual ModeOn/Off Series Model HRC100 and HRC101 Thermostat Series Model HRC200 and HRC201Inspecting Burners Switch OptionalPilot Flame Pattern Burner Flame PatternBurner Injector Holder Pilot Air Inlet Hole Cleaning MaintenanceIf burner flame pattern is incorrect, as shown in Figure Blow air into the primary air holes on the injector holderObserved Problem Possible Cause Remedy TroubleshootingLOG Set CabinetTroubleshooting Noise when burner is lit Delayed ignition of burnerObserve minimum installa White powder residue forming When heated, vapors fromGas leak. See Warning Wiring Diagram SpecificationsReplacement Parts Service HintsMANUAL-controlled models Cgmfn and Cgmfp Illustrated Parts Breakdown101629-02 Parts ListIllustrated Parts Breakdown REMOTE-READY Models WALL-MOUNT ON/OFF Switch AccessoriesReceiver and HAND-HELD Remote Control KIT HRC100 and HRC101 Equipment Shutoff Valve GA5010119315-01A Not a UPC

VGMRN, VGMRP, CGMFN, CGMFP specifications

Desa CGMFP, VGMRN, VGMRP, and CGMFN represent a series of cutting-edge developments designed to optimize various aspects of modern technology and infrastructure. These entities focus on enhancing efficiency, sustainability, and overall performance within their respective domains.

Desa CGMFP, or the Comprehensive Green Manufacturing Facility Program, is dedicated to promoting sustainable manufacturing practices. Its primary features involve the integration of green technologies that minimize waste and energy consumption. The program emphasizes the use of renewable energy sources, such as solar and wind, to power manufacturing operations. This initiative not only reduces the carbon footprint of production processes but also helps organizations meet regulatory standards for environmental protection.

VGMRN, which stands for Variable Grid Management and Resource Network, is a sophisticated system designed to enhance the efficiency of energy distribution. It utilizes advanced algorithms and machine learning to manage energy loads dynamically across the grid. One of the standout characteristics of VGMRN is its ability to forecast energy demand patterns, allowing for proactive adjustments to energy supply. This results in minimized downtime and optimized usage of resources, making it an essential component of smart grid solutions.

VGMRP, or Variable Grid Management and Resource Planning, complements the work of VGMRN by focusing on the strategic planning of resource allocation within energy networks. Its core features include predictive analytics and scenario modeling, which empower utilities to simulate various energy distribution scenarios and make informed decisions. This technological approach not only aids in efficient resource use but also supports resilience against fluctuations in energy supply and demand.

Lastly, CGMFN, the Comprehensive Green Manufacturing Framework Network, provides a robust platform for collaboration across industries engaged in green manufacturing. This network facilitates the sharing of best practices, research advancements, and innovative solutions. Key characteristics of CGMFN include a strong emphasis on interdisciplinary cooperation and the promotion of circular economy principles, which encourage the utilization of recycled materials and waste reduction strategies.

Together, these initiatives encapsulate a forward-thinking approach to manufacturing and energy management. They leverage technology and strategic planning to enhance productivity while ensuring that environmental sustainability remains at the forefront of operations. As industries continue to evolve, Desa CGMFP, VGMRN, VGMRP, and CGMFN will play pivotal roles in shaping a greener, more efficient future.
Top Page Image Contents