Desa DVFE34 installation manual For vinyl siding use vinyl siding stand

Page 9

OWNER’S MANUAL

VENTING INSTALLATION

Continued

3.Attach vent pipe assembly to the fire- place. Set fireplace in front of it’s perma- nent location to insure minimum clear- ances. See page 10, Figure 16 for mini- mum clearances for vertical on rigid vent pipe, and page 10 Figure 17 on flexible vent pipe. Mark the wall for a 10" square hole (for noncombustible ma- terial such as masonry block or concrete, a 7 1/2" diameter hole is acceptable). See Figure 12. The center of the hole should line up with the center-line of the hori- zontal rigid vent pipe. Cut a 10"x10" (254mm x 254mm) square hole through combustible exterior wall (7 1/2" [190mm] diameter hole if noncombustible). Frame as necessary (see Figure 12).

Female

Locking

Lugs

4.Apply a bead of non-hardening mastic around the outside edge of the vent cap. Position the vent cap in the center of the 7 1/2" or 10" hole on the exterior wall with the arrow on the vent cap pointing up. Insure proper clearance of 1" to combustibles is maintained. At- tach the vent cap with four wood screws supplied (see Figure 13). Note: Re- place the wood screws with appropri- ate fasteners for stucco, brick, concrete, or other types of siding.

WARNING: Do not recess vent termination in to any wall. This will cause a fire hazard.

5. For vinyl siding use vinyl siding stand-

offs between vent cap and exterior wall.

The vinyl siding standoff prevents ex-

cessive heat from melting the vinyl sid-

ing material. Bolt the vent cap to the

standoff. Apply non-hardening mastic

around outside edge of the standoff in-

stead of the vent cap assembly. Use

wood screws provided to attach the

7.Carefully move the fireplace with vent assembly attached toward the wall and insert the vent pipe into the horizontal termination. The pipe overlap should be a minimum of 1 1/4". Apply silicone to the outer pipe connection. Fasten all vent connections with screws provided. Refer to Fireplace Installation on page 16 for instructions on securing unit to framing or floor.

8.Slide the wall thimble against the inte- rior wall surface and attach with screws provided (see Figure 15).

Cut Vinyl Siding

Away to Fit

Standoff

Wood Screw

Standoff

Male Slots

standoff. See Figure 14.

6. Slide the wall thimble over the vent

pipe before connecting the horizontal

run to the vent cap (see Figure 15).

UP

Nut

Apply Mastic

to All Four Sides Vent Cap

Bolt

Figure 11 - Rigid Vent Pipe Connections

Vent Opening

Combustible Wall

10"

(254mm)

10"

(254mm)

(Framing

Apply Mastic to All Four Sides

UP

Wood

Screw

Vent Cap

Figure 13 - Installing Horizontal Vent Cap

Figure 14 - Installing Vinyl Siding Standoff

Interior Wall

Surface

Wall

Thimble

Vent Cap

(Horizontal

Screw

 

Termination)

 

Vent Opening

Detail)

Horizontal

Vent Pipe

Noncombustible Wall

7 1/2" (190mm)

Figure 12 - Vent Opening Requirements

Figure 15 - Connecting Vent Cap with Horizontal Vent Pipe

Continued

107205

9

For more information, visit www.desatech.com

Page 8 Page 10
Image 9
Page 8 Page 10
Contents For Your Safety For Your Safety What to do if YOU Smell GASDVFE34 Natural Electronic Ignition DIRECT-VENT Fireplace Safety InformationLocal Codes Product IdentificationGlossary Terms OperationLocation and Space Requirements PRE-INSTALLATION PreparationClearances Framing and FinishingPRE-INSTALLATION General Venting Preparation Location of VentTermination General Venting Installation Precautions Venting InstallationInstallation Planning Installing Vent System in a ChaseSnorkel Termination Installation for Horizontal TerminationFor vinyl siding use vinyl siding stand Rigid Vent Pipe Horizontal Venting Rigid Vent Pipe Horizontal Termination ConfigurationsVenting with Two 90 Elbows Installation for Vertical Termination Flat Ceiling InstallationCathedral Ceiling Installation Venting with Two 90 Elbow s Vertical Termination ConfigurationsVertical Venting High Altitude Installation Parts Lists for Venting Kits and ComponentsFMI Rigid Venting Installing Optional Blower Accessory Fireplace InstallationInstalling GA3700/DA3610TA Blowers Check GAS TypeIf your fireplace system is installed Installation Items Needed Installing GAS Piping to Fireplace LocationConnecting Fireplace to GAS Supply Pressure Testing Gas Supply Piping SystemChecking GAS Connections Close equipment shutoff valve see Fig- ure Pressure Testing Fireplace Gas ConnectionsREMOVING/REPLACING Glass Door Installing Optional Wall Mount Switch GWMS2Attaching Magnetic Decorative Brass Strips Installing Optional Brick Liner D8037AInstalling Log No Installing LOGS, Lava Rock and Glowing EmbersOperating Fireplace For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To ApplianceOperating Optional GWMS2 Wall Mounted Switch Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersGlass Door Cleaning and MaintenancePilot and Burners LogsObserved Problem Possible Cause Remedy TroubleshootingOrifice Gas leak. See Warning statement Service Hints Replacement PartsTechnical Service Wiring DiagramsDVFE34 SpecificationsDVFE34 Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListAccessories 107205 Warranty Information

DVFE34 specifications

Desa DVFE34 is a cutting-edge development designed to meet the demanding needs of modern urban living. This residential complex stands out due to its innovative architecture, sustainable technologies, and its commitment to enhancing the quality of life for its residents.

One of the main features of Desa DVFE34 is its environmentally friendly design. The complex has been constructed with sustainable materials that minimize its carbon footprint. Solar panels are integrated into the building's structure, providing renewable energy for common areas and reducing reliance on non-renewable power sources. The implementation of rainwater harvesting systems ensures efficient use of water resources, promoting sustainability within the community.

In terms of technology, Desa DVFE34 is equipped with smart home capabilities. Residents can control various aspects of their homes—from lighting to heating—through a centralized app on their smartphones. This not only adds convenience but also allows for energy savings and enhances security. The incorporation of security systems with smart alarms and surveillance cameras ensures a safe living environment.

The layout of the building is thoughtfully designed to maximize space and comfort. Spacious apartments come with modern finishes, high ceilings, and large windows that allow plenty of natural light to flow in. Common areas include beautifully landscaped gardens, recreational spaces, and fitness facilities that encourage a healthy lifestyle. Additionally, designated areas for social gatherings foster a sense of community among residents.

Accessibility is a key characteristic of Desa DVFE34. Located in a prime urban area, residents have easy access to public transport, shopping centers, and essential services. This not only facilitates daily commutes but also enhances the overall living experience by placing residents in the heart of the city’s amenities.

In summary, Desa DVFE34 represents a harmonious blend of modern living and sustainable practices. Its innovative features, from smart technologies to eco-friendly designs, set a new standard for urban residential developments. By prioritizing both comfort and sustainability, Desa DVFE34 is an exemplary model of what future living spaces can and should be.
Top Page Image Contents