Desa UNVENTED (VENT-FREE) NATURAL GAS FIREPLACE installation manual Installing, Continued

Page 10

ASSEMBLING AND ATTACHING BRASS TRIM

INSTALLING

Continued

10

ASSEMBLING AND ATTACHING BRASS TRIM

Note: The instructions below show assembling and attaching brass trim to fireplace. You cannot attach the brass trim as described below for built-in installation (see page 13).

1.Remove packaging from three pieces of brass trim.

2.Locate four brass screws, two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 5.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 5).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 5).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other side.

Top Brass Trim

Side Brass Trim

Set Screws

Adjusting

Plate

Shim

Slot

Mitered Edge

Slot

Figure 5 - Assembling Brass Trim

8.Place the assembled trim onto fireplace cabinet. Attach to fireplace with brass screws included in hardware package (see Figure 6).

Assembled

Brass Trim

Screws

Figure 6 - Attaching Brass Trim to Fireplace

101742

Image 10

Contents Save this manual for future reference OWNER’S OPERATION AND INSTALLATION MANUALUNVENTED VENT-FREENATURAL GAS FIREPLACE DANGER CONTENTS SAFETY INFORMATIONWARNINGS Safety Information continues on next pageINFORMATION SAFETYContinued Figure 1 - Log Base Assembly PRODUCT IDENTIFICATIONFigure 2 - Fireplace Operation LOCAL CODES UNPACKING PRODUCT FEATURESSafety Device Piezo Ignition SystemAIR FOR COMBUSTION AND VENTILATION PROVIDING ADEQUATE VENTILATIONCOMBUSTION AIR FORVENTILATION ContinuedVENTILATION AIR AIR FOR COMBUSTION AND VENTILATIONContinued Ventilation Air from Inside BuildingNOTICE INSTALLINGContinued Continued INSTALLINGASSEMBLING AND ATTACHING BRASS TRIM Continued INSTALLINGINSTALLATION CLEARANCES CONVENTIONAL FIREPLACE INSTALLATIONContinued INSTALLINGheads and putty over Continued INSTALLINGBUILT-INFIREPLACE INSTALLATION ContinuedContinued INSTALLINGFigure 13 - Attaching Nailing Flange Accessory 39 3/8 27 7/8 35 1/2 55 5/8Continued INSTALLINGMantel Clearances for Built-InInstallation ContinuedInstallation Items Needed INSTALLINGINSTALLING GAS PIPING TO FIREPLACE LOCATION NOTICEInstallation Items Needed INSTALLINGCONNECTING FIREPLACE TO GAS SUPPLY ContinuedNOTICE G 001WARNINGINSTALLING ContinuedContinued INSTALLINGPressure Testing Fireplace Gas Connections ContinuedFigure 21 - Installing Rear Log INSTALLINGINSTALLING LOGS Figure 22 - Installing Front LogContinued INSTALLINGFigure 23 - Installing Crossover Log ContinuedINSTALLING FOR YOUR SAFETY READ BEFORE LIGHTINGOPERATING FIREPLACE ContinuedNOTICE OPERATINGFIREPLACE LIGHTING INSTRUCTIONSVARIABLE OUTPUT CONTROL OPERATION MANUAL LIGHTING PROCEDURETO TURN OFF GAS TO APPLIANCE OPERATING FIREPLACENOTICE INSPECTINGBURNERS PILOT FLAME PATTERNODS/PILOT AND BURNERS CLEANING AND MAINTENANCE TROUBLE SHOOTINGLOGS Continued TROUBLE- SHOOTINGCleaning and Mainte ContinuedCleaning and Mainte TROUBLE SHOOTINGCleaning and Mainte Cleaning and MainteContinued TROUBLESHOOTING leaks see Checking GasWhen gas pressure is too low TECHNICAL SERVICE SERVICE HINTSREPLACEMENT PARTS SPECIFICATIONS When gas quality is badGMC12U - Unfinished ACCESSORIESCABINET MANTEL GMC11F - Walnut Finished HEARTH BASE GC3333F- Walnut FinishedPARTS Log Base AssemblyILLUSTRATED BREAKDOWNPART NUMBER PARTS LISTLog Base Assembly DESCRIPTIONPARTS FireplaceILLUSTRATED BREAKDOWNPART NUMBER PARTS LISTFireplace DESCRIPTIONLIMITED WARRANTY VENT-FREENATURAL GAS FIREPLACE WARRANTY INFORMATIONKEEP THIS WARRANTY