Vermont Casting DVT38 Fuel Conversion Instructions, Conversion Precautions, Conversion Procedure

Page 29

Chateau™

Fuel Conversion Instructions

WARNING! This conversion kit shall be installed by a qualified service agency in accordance with the manufacturerʼs instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or pro- duction of carbon monoxide may result causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked as specified in the manufacturerʼs instructions supplied with the kit.

CAUTION: The gas supply shall be shut off prior to disconnecting the electrical power, before pro- ceeding with the conversion.

Avertissement: Cette trousse de conversion

Ne doit être installée que par le représentant dʼun organisme qualifié et conformément aux instruc- tions du fabricant et aux codes et exigences pertinentes de lʼautorité compétente. Quiconque ne respecte pas à la lettre les instrucitons du présent guide risque de déclencher un incendie, une explosion ou le dégagement de monoxyde de carbone entraînant des dommages matériels, des lésions corporelles ou la perte de vies humaines. Lʼorganisme qualifié qui effectur les travaux est responsible de lʼinstallation de cette trousse. Lʼinstallation nʼest pas terminée tant que le fonc- tionnement de lʼappareil converti nʼa pas été vérifié selon la notice du fabricant qui accompagne la trousse.

ATTENTION: Avant dʼeffectuer la conversin, coupez dʼabord lʼlimentation en gaz, ensuite, coupez lʼalimentation électrique.

Conversion Precautions

Allow unit to cool if it has been operating.

Before proceeding with conversion, turn control knob on valve to OFF and turn gas supply OFF. Turn OFF any electricity that may be going to appliance.

Conversion Procedure

1.Remove glass frame. Refer to Glass Frame Assembly section on Page 20.

2.Remove lava rock, volcanic rock, embers and logs.

CAUTION: Logs may be hot.

3.With a Phillips or Robertson screwdriver, remove the two (2) screws holding the fettle to the burner assem- blies. With a hex, remove the two (2) hex nuts holding

the burner tube to the front of the burner assembly. Remove burner tube.

4.Remove two (2) hex nuts holding the left burner leg. Remove burner leg. (Fig. 53)

 

KT416

Fig. 53

Use 3/8” socket to remove hex nuts holding left burner

leg.

 

5.Slide the burner housing assembly to the left and away.

6.Replace the three (3) injectors. Refer to Table 1.

7.Replace pilot orifice.

8.Remove pilot hood by lifting up. (Fig. 54) NOTE: It is not necessary to remove the pilot tube for conversion.

9.Remove pilot orifice with 5/32” Allen wrench. (Fig. 55)

Pilot Hood

Pilot

Bracket

CO105a

Fig. 54 Remove pilot hood.

Index Tab

Allen Wrench

Snap Ring

 

 

CO106a

Fig. 55 Remove pilot orifice.

 

20006081

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents What to do if YOU Smell GAS INSTALLER/CONSUMER Safety InformationTable of Contents Please Review the Following Carefully Installation & Operating InstructionsLocating Your Fireplace Fireplace Dimensions DVT38 Mantels Clearance to CombustiblesNailing flanges Framing and FinishingFinal Finishing Gas Line InstallationGas Inlet and Manifold Pressures Gas SpecificationsElectronic Gas Control Valve Remote ON/OFF SwitchElectrical Junction Box E Units Only Location of Vent Termination General VentingGeneral Venting Information Termination Location Canadian Installations1 US Installations2Quick Reference for Fresh Air Restrictor Plate / Flue Baffle USA Installations Canadian InstallationsGeneral Information Assembling Vent Pipes SK8 Venting Pipes Horizontal TerminationDVT38 only Sidewall ApplicationsDVT44 only Step Sidewall InstallationLocate vent opening on wall Always install horizontal venting on a level planeFresh Air Restrictor Plate Typical offset application Vertical Through-the-Roof InstallationMin 610mm Component Description Model Number Chimney ComponentsGlass Frame Assembly Removal Glass Information Glass CleaningRestrictor Plates Installation Operating InstructionsFresh Air Restrictor Plate Adjustment Ceramic Refractory InstallationLog, Lava Rock and Ember Placement Place log rear onto rear log bracket RN/RP & EN/EP Models Flame & Temperature AdjustmentFlame Characteristics To Turn Off Gas To Heater Lighting And Operating InstructionsLighting Instructions Lighting and Operating InstructionsTurning Off the Gas to the Appliance Valve in the on positionSIT Nova 820 Millivolt Valve Troubleshooting the Gas Control SystemSIT 822 Valve with a Honeywell Electronic Ignitor Fuel Conversion Instructions Conversion PrecautionsConversion Procedure Remove valve regulator Pilot Flame AdjustmentInjector Orifice Size Matrix Cleaning the Standing Pilot Control System MaintenanceCleaning Electronic Ignition System Battery Replacement for Ignitor ModuleDVT38, DVT44 DVT38 DVT44 DVT38, DVT44Fuel Conversion Kits Remote Controls AccessoriesFull Surround Mantel Model Functions ControlledChateau Chateau If Warranty Service is NEEDED… Product Covered by this WarrantyModel EnerGuide Ratings Fireplace Efficiency % Efficiency Ratings

DVT38 specifications

The Vermont Casting DVT38 is a standout model in the realm of contemporary gas fireplaces, epitomizing both innovative engineering and aesthetic elegance. Designed with a focus on efficiency and style, the DVT38 offers homeowners an exceptional heating experience while enhancing the ambiance of their living spaces.

One of the main features of the Vermont Casting DVT38 is its impressive heat output. With a BTU range that ensures warmth for larger areas, the fireplace is capable of efficiently heating spaces without consuming excessive fuel. This is a critical aspect for homeowners seeking both comfort and energy savings. The fireplace integrates a dual burner system, promoting a uniform heat distribution and ensuring that every corner of the room enjoys consistent warmth.

Another notable characteristic of the DVT38 is its advanced burner technology. The unique burner design allows for a natural gas or propane option, giving consumers flexibility based on availability and preference. The adjustable flame settings enable users to customize the heat output and ambiance, perfect for both cozy winter evenings and social gatherings.

In terms of aesthetics, the Vermont Casting DVT38 boasts a sophisticated design that complements various interior styles. It features large glass viewing areas which present a captivating flame pattern, enhancing the visual appeal of the unit. The contemporary facade can be finished with a variety of trims and options, allowing homeowners to tailor the fireplace to their personal décor.

The DVT38 is also equipped with an easy-to-use electronic ignition system, further simplifying the operation. This feature ensures that lighting the fireplace is hassle-free, eliminating the need for matches or manual lighting. Additionally, many models come with a remote control option, allowing users to adjust settings from a distance, thereby enhancing convenience and usability.

Moreover, the DVT38 is built with durability in mind, incorporating high-quality materials that withstand the test of time while providing a reliable heating solution. Vermont Castings is renowned for its commitment to craftsmanship, and this model exemplifies that ethos.

In summary, the Vermont Casting DVT38 is an exquisite blend of functionality and design. With efficient heating capabilities, cutting-edge technology, and customizable aesthetics, it stands out as a premier choice for anyone looking to elevate their home heating experience. Whether for warmth or ambiance, the DVT38 is engineered to deliver satisfaction for years to come.
Top Page Image Contents