Vermont Casting DVT38 installation instructions Pilot Flame Adjustment, Remove valve regulator

Page 30

Chateau™

10. Install the conversion orifice.

11. Reinstall pilot hood. Be sure to align hood with index

tab.

12. Open the control panel and remove the cover by

removing two (2) screws. While holding the valve

cover plate with one hand, disconnect the wiring to

the switch and the pilot indicator. NOTE: Do not allow

the valve cover plate to hang from the pilot wires as

E

this could damage the wires. Remove the extension

knob(s). Replace the valve regulator.

13. Using the TORX T20 bit remove and discard the three

(3) pressure regulator mounting screws (A), pressure

regulator tower (B) and the spring and diaphragm as-

sembly (C). (Fig. 56)

A

O

F

OFF

P

I TO L

D

FC108

B

C

 

OFF

 

P

 

 

I

O

TO

L

 

FC107

Fig. 56 Remove valve regulator.

14.Insure the rubber gasket (D) is properly positioned and install the new HI/LO pressure regulator assembly to the valve using the new screws (E) supplied with the kit. Tighten the screws securely. (Ref. torque = in/lb) (Fig. 57)

15.Install the enclosed identification label (F) to the valve body where it can easily be seen. (Fig. 57)

16.Regulator conversion complete.

17.Test for Leaks

•Apply gas to the system and light the pilot.

•With a soapy solution check for leaks around the pilot assembly where the tube enters the pilot as- sembly. Tighten fitting if necessary.

Fig. 57 Replace regulator.

•Light the main burner and check for leaks around the new pressure regulator assembly. Tighten screws if necessary.

•With the main burner “ON” check for leaks around the burner orifice. Be careful of the burner flame. Tighten orifice if necessary.

•With the main burner “ON” rotate the HI/LO knob and verify proper burner operation.

18.Replace burner to original position.

19.Replace burner leg.

20.Replace burner tube and fettle.

21.Follow instructions on Page 22 to reinstall logs, lava rock, volcanic rock and embers.

22.Replace glass frame.

Conversion complete.

Pilot Flame Adjustment

Typically, the top 3/8” or 1/2” of the thermopile should be engulfed in the pilot flame. (Page 24, Fig. 50)

To adjust pilot burner:

1.Remove pilot adjustment cap located on valve.

2.Adjust pilot screw to provide properly sized flame.

3.Replace pilot adjustment cap.

30

20006081

Page 29 Page 31
Image 30
Page 29 Page 31
Contents INSTALLER/CONSUMER Safety Information What to do if YOU Smell GASTable of Contents Installation & Operating Instructions Locating Your FireplacePlease Review the Following Carefully Fireplace Dimensions DVT38 Clearance to Combustibles MantelsFraming and Finishing Nailing flangesGas Inlet and Manifold Pressures Gas Line InstallationFinal Finishing Gas SpecificationsRemote ON/OFF Switch Electrical Junction Box E Units OnlyElectronic Gas Control Valve General Venting Location of Vent TerminationCanadian Installations1 US Installations2 General Venting Information Termination LocationQuick Reference for Fresh Air Restrictor Plate / Flue Baffle General Information Assembling Vent Pipes SK8 Venting Pipes Canadian InstallationsUSA Installations Horizontal TerminationSidewall Applications DVT44 onlyDVT38 only Sidewall Installation StepAlways install horizontal venting on a level plane Locate vent opening on wallFresh Air Restrictor Plate Vertical Through-the-Roof Installation Typical offset applicationMin 610mm Chimney Components Component Description Model NumberRestrictor Plates Installation Glass Information Glass CleaningGlass Frame Assembly Removal Operating InstructionsCeramic Refractory Installation Fresh Air Restrictor Plate AdjustmentLog, Lava Rock and Ember Placement Place log rear onto rear log bracket Flame & Temperature Adjustment Flame CharacteristicsRN/RP & EN/EP Models Lighting And Operating Instructions To Turn Off Gas To HeaterTurning Off the Gas to the Appliance Lighting and Operating InstructionsLighting Instructions Valve in the on positionTroubleshooting the Gas Control System SIT Nova 820 Millivolt ValveSIT 822 Valve with a Honeywell Electronic Ignitor Conversion Precautions Conversion ProcedureFuel Conversion Instructions Pilot Flame Adjustment Remove valve regulatorInjector Orifice Size Matrix Cleaning Electronic Ignition System MaintenanceCleaning the Standing Pilot Control System Battery Replacement for Ignitor ModuleDVT38, DVT44 DVT38, DVT44 DVT38 DVT44Fuel Conversion Kits Full Surround Mantel AccessoriesRemote Controls Model Functions ControlledChateau Chateau Product Covered by this Warranty If Warranty Service is NEEDED…Efficiency Ratings Model EnerGuide Ratings Fireplace Efficiency %

DVT38 specifications

The Vermont Casting DVT38 is a standout model in the realm of contemporary gas fireplaces, epitomizing both innovative engineering and aesthetic elegance. Designed with a focus on efficiency and style, the DVT38 offers homeowners an exceptional heating experience while enhancing the ambiance of their living spaces.

One of the main features of the Vermont Casting DVT38 is its impressive heat output. With a BTU range that ensures warmth for larger areas, the fireplace is capable of efficiently heating spaces without consuming excessive fuel. This is a critical aspect for homeowners seeking both comfort and energy savings. The fireplace integrates a dual burner system, promoting a uniform heat distribution and ensuring that every corner of the room enjoys consistent warmth.

Another notable characteristic of the DVT38 is its advanced burner technology. The unique burner design allows for a natural gas or propane option, giving consumers flexibility based on availability and preference. The adjustable flame settings enable users to customize the heat output and ambiance, perfect for both cozy winter evenings and social gatherings.

In terms of aesthetics, the Vermont Casting DVT38 boasts a sophisticated design that complements various interior styles. It features large glass viewing areas which present a captivating flame pattern, enhancing the visual appeal of the unit. The contemporary facade can be finished with a variety of trims and options, allowing homeowners to tailor the fireplace to their personal décor.

The DVT38 is also equipped with an easy-to-use electronic ignition system, further simplifying the operation. This feature ensures that lighting the fireplace is hassle-free, eliminating the need for matches or manual lighting. Additionally, many models come with a remote control option, allowing users to adjust settings from a distance, thereby enhancing convenience and usability.

Moreover, the DVT38 is built with durability in mind, incorporating high-quality materials that withstand the test of time while providing a reliable heating solution. Vermont Castings is renowned for its commitment to craftsmanship, and this model exemplifies that ethos.

In summary, the Vermont Casting DVT38 is an exquisite blend of functionality and design. With efficient heating capabilities, cutting-edge technology, and customizable aesthetics, it stands out as a premier choice for anyone looking to elevate their home heating experience. Whether for warmth or ambiance, the DVT38 is engineered to deliver satisfaction for years to come.
Top Page Image Contents