Breckwell P22FSL, P22I owner manual Operation

Page 14

14

OPERATION

PANEL CONTROLS (See Figure 22)

The blowers and automatic fuel supply are controlled from a panel on the left-hand side of the P22. The control panel functions are as follows.

a.ON/OFF SWITCH

∙When pushed the stove will automatically ignite. No other firestarter is necessary. The igniter will stay on for at least 10 and up to 15 minutes, depending on when Proof of Fire is reached. The fire should start in about 5 minutes.

∙The green light located above the On/Off button (in the On/Off box) will flash during the ignition start-up period. (See figure 22)

∙The Feed Rate Advance is inoperable during the ignition start period. When the red light continuously stays on the Feed Rate Advance can be adjusted to achieve the desired heat output.

NOTE: If the stove has been shut off, and you want to re-start it while it is still warm, the “on/off” button must be held down for 2 seconds.

b.FUEL FEED SWITCH

∙When the “Fuel Feed” button is pushed and held down the stove will feed pellets continuously into the burnpot.

∙While the stove’s auger system is feeding pellets the amber light (in the “Fuel Feed” box) will be on. (See figure 22)

CAUTION: DO NOT USE THIS CONTROL DURING NORMAL OPERATION BECAUSE IT COULD SMOTHER THE FIRE AND LEAD TO A DANGEROUS SITUATION.

c.HIGH FAN SWITCH

∙The room air fan speed varies directly with the feed rate. The “HIGH FAN” switch overrides this variable speed function. It will set the room air blower speed to high at any feed rate setting.

∙When the “HIGH FAN” button is pushed the room air fan will switch to its highest setting.

∙When this button is pushed again the room air fan will return to its original setting based on the Feed Rate Advance setting.

d.RESET TRIM

Different size and quality pellet fuel may require adjustment of the “1” feed setting on the Feed Rate Advance bar graph. This is usually a one-time adjustment based on the fuel you are using. The “RESET TRIM” button when adjusted will allow for 3 different feed rate settings for the #1 feed setting only. To adjust simply push the “RESET TRIM” button while the stove is operating at setting “1” and watch the bar graph.

∙When the “1” and “3” lights are illuminated on the bar graph the low feed rate is at its “lowest” setting. (approx. 0.9 pounds per hour)

∙When the “1” light is illuminated on the bar graph the low feed rate is at its “normal” setting.

∙When the “1” & “4” lights are illuminated on the bar graph the low feed rate is at its “highest” setting.

NOTE: When the stove is set on “1” the “reset trim” values will be shown on the Feed Rate Advance bar graph. For example if the Reset Trim is set to its lowest setting every time the stove is set to low the “1” and “3” lights will be illuminated on the bar graph.

e.HEAT LEVEL ADVANCE

∙This button when pushed will set the pellet feed rate, hence the heat output of your stove. The levels of heat output will incrementally change on the bar graph starting from level “1” to “4”.

NOTE: When dropping more than 2 heat level settings (i.e. 4 to 1) push the ‘High Fan’ button and allow the room air fan to run at that setting for at least 5 minutes to prevent the stove from tripping the high temp thermodisk. If the high temp thermodisk does trip see “SAFETY FEATURES”.

CAUTION: THE “4” SETTING IS DESIGNED FOR TEMPORARY USE ONLY. IF USED FOR EXTENDED PERIODS, IT CAN SHORTEN THE LIFE EXPECTANCY OF THE UNITS COMPONENTS. AVOID USE AT THIS SETTING FOR MORE THAN ONE HOUR AT A TIME.

FIGURE 22

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Economy Series P22 Introduction Important InformationSafety Precautions Table of Contents Preparation InstallationSpecifications ClearancesVenting When Outside AIR is not UsedCombustion AIR Supply Assembling Pedestal or LEG SET Freestanding InstallationsEquivalent Vent Length EVL Horizontally Through Wall refer to FigureVertically with NEW Chimney System Refer to Figure Vertically Into Existing Chimney SystemInstallation Through Side of Masonry Chimney Vertically Into Existing Masonry FireplaceInsert Installations Assembling the Flashing SETWhen Vent Pipe Extends to Chimney TOP Refer to Figures 16 Chase dimensions shown are minimums and must be maintained AS a BUILT-IN FireplaceCombustion AIR Supply Electrical InstallationSpecial Mobile Home Requirements Operation Building a Fire Proper FuelPRE-START-UP Check Hotrod Automatic FirestarterSafety Features Breckwell Maintenance ToolShutdown Procedure RE-STARTING a Warm StoveOptional Thermostat Thermostat InstallationThermostat Installation ∙ a Millivolt Thermostat is RequiredPlease Read this ASH Removal MaintenanceCleaning ASH DisposalBlowers Chimney Cleaning Daily Weekly Annually or per TonPossible Causes Troubleshooting GuideStove Shuts OFF and the # 2 Light Flashes Stove Shuts OFF and the # 3 Light Flashes Smoke Smell Coming Back Into the Home Stove Feeds PELLETS, but will not IgnitePossible Causes Possible Remedies Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide Smoke Smell or Soot BUILD-UP High Limit Switch Keeps TrippingHeat Level Setting P22 Digital Circuit Board Timing RatesElectrical Diagram Replacement Parts BurnpotLifetime Limited Warranty
Related manuals
Manual 29 pages 58.71 Kb

P22FSL, P22I specifications

Breckwell has established itself as a key player in the realm of pellet stoves, with its P22 series being a testament to its commitment to innovation, efficiency, and user comfort. The P22I, P22FSL, and P22FSA models each boast unique features, yet all are designed with the same high-quality standards that Breckwell is known for.

The Breckwell P22I is an Intelligent pellet stove that stands out for its sleek design and exceptional heating capacity. It delivers up to 50,000 BTUs, making it suitable for larger spaces while ensuring efficient heat distribution. One of its main features is the intuitive digital control board with advanced programming options, allowing users to set their desired temperature and heating schedules effortlessly. The P22I also supports an optional direct vent system, increasing safety by minimizing the risk of backdrafts and ensuring proper exhaust flow.

The P22FSL model showcases a more modern aesthetic with its large viewing window, allowing users to enjoy the mesmerizing flames of the fire while heating their homes. Its side-loading feature offers convenience when it comes to refilling pellets. The P22FSL also incorporates a powerful blower to enhance heat circulation throughout the room. Furthermore, it features an adjustable heat output, providing users with the ability to customize their heating experience based on their preferences.

For those seeking a more traditional look, the P22FSA provides a classic yet efficient design. This model is perfect for homes that emphasize a more rustic charm while still delivering all the benefits of a modern pellet stove. Like its counterparts, the P22FSA provides robust heating capabilities of up to 50,000 BTUs. It also features a simple control panel, making it accessible for users of all technical backgrounds.

All three models utilize a reliable feed system that ensures a consistent flow of pellets, allowing for prolonged operational time before needing a refill. Additionally, they are equipped with safety features such as a thermal sensor and automatic shut-off to prevent overheating, offering peace of mind for users.

In terms of efficiency, the P22 series meets stringent EPA standards, making them environmentally friendly options for home heating. The use of premium materials in their construction ensures durability and longevity, making them a wise investment for homeowners looking to combine comfort with sustainability. Overall, the Breckwell P22I, P22FSL, and P22FSA models reflect the brand’s dedication to quality, comfort, and innovation in the pellet stove market.
Top Page Image Contents