Breckwell P22I, P22FSL Installation, Specifications, Preparation, Clearances, Floor Protection

Page 5

INSTALLATION

5

SPECIFICATIONS

FREESTANDING:

Width: 21 ½”

Height: 28 ½” (with legs or pedestal)

Depth: 24”

Weight: 185 lbs.

Pedestal: 40 lbs.

Legs: 13 lbs.

Flue size: 3” or 4”

Hopper Capacity: Up to 45 lbs.

(this can vary widely depending on pellet size, length, and diameter) EPA status: exempt

Burn time: 1 lb. to 4 ½ lbs. per hour

BTU range: 8,200 to 40,000

Approved installations: mobile home, alcove, conventional

FIREPLACE INSERT:

Width: 21 ½” (With flashing: 39”)

Height: 20” (With flashing: 30”)

Depth: 24” (In fireplace: 10 ¾”)

Weight: 185 lbs.

Flashing: 13 lbs.

Flue size: 3” or 4”

Hopper Capacity: Up to 45 lbs.

(this can vary widely depending on pellet size, length, and diameter) EPA status: exempt

Burn time: 1 lb. to 4 ½ lbs. per hour

BTU range: 8,200 to 40,000

Approved installations: zero-clearance, masonry, as a built-in

PREPARATION

Factory packaging must be removed, and some minor assembly work is required prior to installation. Access to the rear of the stove is necessary.

The circuit board/control panel must be unpacked and installed in the side flashing on the insert or side panel on the freestanding.

(See installation instructions provided with the circuit board)

NOTE: Normally, your dealer will perform these functions.

CLEARANCES

The Breckwell P22 Freestanding has been tested and listed for installation in residential, mobile home and alcove applications.

The P22 Insert is approved for installation into code complying masonry fireplaces. It is also approved for use in listed factory built fireplaces (UL 127) and standard residential built-ins (see As A Built-In Fireplace), including Mobile Home built-in installations, of the following description: all brands at least 34” wide and 20 ½” high.

FLOOR PROTECTION: Freestanding installations, minimum 21” wide by 28” deep. The stove must be placed on a continuous (grouted joints) noncombustible material such as ceramic tile, cement board, brick, 3/8” millboard or equivalent, or other approved or listed material suited for floor protection.

THE MATERIAL(S) USED MUST HAVE, OR COMBINE TO HAVE, A MINIMUM INSULATIVE RATING OF ‘R1’.

NOTE: ceramic tile, or any tile, requires a continuous sheet beneath to prevent the possibility of embers falling through to the combustible floor if cracks or separation should occur in the finished surface, this would include floor protection for Built-in raised hearths. Check local codes for approved alternatives.

Clearances are measured from the sides, back and face (door opening) or stove body (refer to fig. 4).

DO NOT USE MAKESHIFT MATERIALS OR COMPROMISES IN THE INSTALLATION OF THIS UNIT.

INSTALL VENT WITH CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

FIGURE 1

ALCOVE CLEARANCES

FIGURE 2

FIGURE 3

FLOOR PROTECTION

FIGURE 4

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Economy Series P22 Important Information IntroductionSafety Precautions Table of Contents Specifications InstallationPreparation ClearancesVenting When Outside AIR is not UsedCombustion AIR Supply Equivalent Vent Length EVL Freestanding InstallationsAssembling Pedestal or LEG SET Horizontally Through Wall refer to FigureVertically Into Existing Chimney System Vertically with NEW Chimney System Refer to FigureVertically Into Existing Masonry Fireplace Installation Through Side of Masonry ChimneyAssembling the Flashing SET Insert InstallationsWhen Vent Pipe Extends to Chimney TOP Refer to Figures 16 AS a BUILT-IN Fireplace Chase dimensions shown are minimums and must be maintainedCombustion AIR Supply Electrical InstallationSpecial Mobile Home Requirements Operation PRE-START-UP Check Proper FuelBuilding a Fire Hotrod Automatic FirestarterShutdown Procedure Breckwell Maintenance ToolSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat ∙ a Millivolt Thermostat is RequiredPlease Read this Cleaning MaintenanceASH Removal ASH DisposalBlowers Daily Weekly Annually or per Ton Chimney CleaningPossible Causes Troubleshooting GuideStove Shuts OFF and the # 2 Light Flashes Stove Shuts OFF and the # 3 Light Flashes Possible Causes Possible Remedies Stove Feeds PELLETS, but will not IgniteSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide Heat Level Setting P22 High Limit Switch Keeps TrippingSmoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram Burnpot Replacement PartsLifetime Limited Warranty
Related manuals
Manual 29 pages 58.71 Kb

P22FSL, P22I specifications

Breckwell has established itself as a key player in the realm of pellet stoves, with its P22 series being a testament to its commitment to innovation, efficiency, and user comfort. The P22I, P22FSL, and P22FSA models each boast unique features, yet all are designed with the same high-quality standards that Breckwell is known for.

The Breckwell P22I is an Intelligent pellet stove that stands out for its sleek design and exceptional heating capacity. It delivers up to 50,000 BTUs, making it suitable for larger spaces while ensuring efficient heat distribution. One of its main features is the intuitive digital control board with advanced programming options, allowing users to set their desired temperature and heating schedules effortlessly. The P22I also supports an optional direct vent system, increasing safety by minimizing the risk of backdrafts and ensuring proper exhaust flow.

The P22FSL model showcases a more modern aesthetic with its large viewing window, allowing users to enjoy the mesmerizing flames of the fire while heating their homes. Its side-loading feature offers convenience when it comes to refilling pellets. The P22FSL also incorporates a powerful blower to enhance heat circulation throughout the room. Furthermore, it features an adjustable heat output, providing users with the ability to customize their heating experience based on their preferences.

For those seeking a more traditional look, the P22FSA provides a classic yet efficient design. This model is perfect for homes that emphasize a more rustic charm while still delivering all the benefits of a modern pellet stove. Like its counterparts, the P22FSA provides robust heating capabilities of up to 50,000 BTUs. It also features a simple control panel, making it accessible for users of all technical backgrounds.

All three models utilize a reliable feed system that ensures a consistent flow of pellets, allowing for prolonged operational time before needing a refill. Additionally, they are equipped with safety features such as a thermal sensor and automatic shut-off to prevent overheating, offering peace of mind for users.

In terms of efficiency, the P22 series meets stringent EPA standards, making them environmentally friendly options for home heating. The use of premium materials in their construction ensures durability and longevity, making them a wise investment for homeowners looking to combine comfort with sustainability. Overall, the Breckwell P22I, P22FSL, and P22FSA models reflect the brand’s dedication to quality, comfort, and innovation in the pellet stove market.
Top Page Image Contents