Breckwell P22FSL, P22I RE-STARTING a Warm Stove, If Stove Runs OUT of Pellets, Refueling

Page 16

16

OPERATION

RE-STARTING A WARM STOVE

If the stove has been shut off, and you want to re-start it while it is still warm, the “on/off” button must be held down for 2 seconds.

IF STOVE RUNS OUT OF PELLETS

The fire goes out and the auger motor and blowers will run until the stove cools. This will take 30 to 45 minutes. After the stove components stop running the “Power” and the BAR GRAPH lights stay on for 10 minutes.

After the 10 minutes the “3” light on the bar graph will flash and the “Power” light will go off.

To restart, refill hopper, press “Power” button, and then press “Fuel Feed” button until pellets begin to fall into burnpot.

REFUELING

We recommend that you not let the hopper drop below ¼ full.

KEEP HOPPER LID CLOSED AT ALL TIMES EXCEPT WHEN REFILLING. DO NOT OVERFILL HOPPER.

BRECKWELL MAINTENANCE TOOL

A tool has been provided to help with the following functions:

FIGURE 23

a.Stirring pellets in hopper – unlike liquids in a tank, pellets do not drain evenly into the auger. Bridging across the opening can occur. Pellets can hang up on the sides of the hopper. Occasionally “stirring” the hopper can help.

NOTE: To help prevent bridging of pellets, common wax paper can be rubbed on the sidewalls and bottom of the hopper.

b.Cleaning heat exchanger tubes – see instructions in “CLEANING”.

c.Scrape ashes from burnpot.

SHUTDOWN PROCEDURE

Turning your Breckwell stove off is a matter of pressing the “Power” control panel switch. The red light will go out. The blowers will continue to operate until internal firebox temperatures have fallen to a preset level.

SAFETY FEATURES

a.Your stove is equipped with a high temperature thermodisc. This safety switch has two functions.

1.To recognize an overheat situation in the stove and shut down the fuel feed or auger system.

2.In case of a malfunctioning convection blower, the high-temperature thermodisc will automatically shut down the auger, preventing the stove from overheating.

NOTE: On some units, once tripped, like a circuit breaker, the reset button will have to be pushed before restarting your stove. On other units the thermodisk has no reset button and will reset itself once the stove has cooled. The manufacturer recommends that you call your dealer if this occurs as this may indicate a more serious problem. A service call may be required.

b.If the combustion blower fails, an air pressure switch will automatically shut down the auger.

NOTE: Opening the stove door for more than 30 seconds during operation will cause enough pressure change to activate the air switch, shutting the fuel feed off. Close the door and press “On/Off” button to continue operation of your stove.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Economy Series P22 Introduction Important InformationSafety Precautions Table of Contents Installation SpecificationsPreparation ClearancesCombustion AIR Supply When Outside AIR is not UsedVenting Freestanding Installations Equivalent Vent Length EVLAssembling Pedestal or LEG SET Horizontally Through Wall refer to FigureVertically with NEW Chimney System Refer to Figure Vertically Into Existing Chimney SystemInstallation Through Side of Masonry Chimney Vertically Into Existing Masonry FireplaceInsert Installations Assembling the Flashing SETWhen Vent Pipe Extends to Chimney TOP Refer to Figures 16 Chase dimensions shown are minimums and must be maintained AS a BUILT-IN FireplaceSpecial Mobile Home Requirements Electrical InstallationCombustion AIR Supply Operation Proper Fuel PRE-START-UP CheckBuilding a Fire Hotrod Automatic FirestarterBreckwell Maintenance Tool Shutdown ProcedureSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat ∙ a Millivolt Thermostat is RequiredPlease Read this Maintenance CleaningASH Removal ASH DisposalBlowers Chimney Cleaning Daily Weekly Annually or per TonStove Shuts OFF and the # 2 Light Flashes Troubleshooting GuidePossible Causes Stove Shuts OFF and the # 3 Light Flashes Stove Feeds PELLETS, but will not Ignite Possible Causes Possible RemediesSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide High Limit Switch Keeps Tripping Heat Level Setting P22Smoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram Replacement Parts BurnpotLifetime Limited Warranty
Related manuals
Manual 29 pages 58.71 Kb

P22FSL, P22I specifications

Breckwell has established itself as a key player in the realm of pellet stoves, with its P22 series being a testament to its commitment to innovation, efficiency, and user comfort. The P22I, P22FSL, and P22FSA models each boast unique features, yet all are designed with the same high-quality standards that Breckwell is known for.

The Breckwell P22I is an Intelligent pellet stove that stands out for its sleek design and exceptional heating capacity. It delivers up to 50,000 BTUs, making it suitable for larger spaces while ensuring efficient heat distribution. One of its main features is the intuitive digital control board with advanced programming options, allowing users to set their desired temperature and heating schedules effortlessly. The P22I also supports an optional direct vent system, increasing safety by minimizing the risk of backdrafts and ensuring proper exhaust flow.

The P22FSL model showcases a more modern aesthetic with its large viewing window, allowing users to enjoy the mesmerizing flames of the fire while heating their homes. Its side-loading feature offers convenience when it comes to refilling pellets. The P22FSL also incorporates a powerful blower to enhance heat circulation throughout the room. Furthermore, it features an adjustable heat output, providing users with the ability to customize their heating experience based on their preferences.

For those seeking a more traditional look, the P22FSA provides a classic yet efficient design. This model is perfect for homes that emphasize a more rustic charm while still delivering all the benefits of a modern pellet stove. Like its counterparts, the P22FSA provides robust heating capabilities of up to 50,000 BTUs. It also features a simple control panel, making it accessible for users of all technical backgrounds.

All three models utilize a reliable feed system that ensures a consistent flow of pellets, allowing for prolonged operational time before needing a refill. Additionally, they are equipped with safety features such as a thermal sensor and automatic shut-off to prevent overheating, offering peace of mind for users.

In terms of efficiency, the P22 series meets stringent EPA standards, making them environmentally friendly options for home heating. The use of premium materials in their construction ensures durability and longevity, making them a wise investment for homeowners looking to combine comfort with sustainability. Overall, the Breckwell P22I, P22FSL, and P22FSA models reflect the brand’s dedication to quality, comfort, and innovation in the pellet stove market.
Top Page Image Contents