Breckwell P22FSL Stove Feeds PELLETS, but will not Ignite, Possible Causes Possible Remedies

Page 24

24

TROUBLESHOOTING GUIDE

STOVE FEEDS PELLETS, BUT WILL NOT IGNITE

Possible Causes:

Possible Remedies:

 

 

 

1.

Air damper open too far for ignition.

Push the air damper in closer to the side of the stove for startup. In

 

 

some situations it may be necessary to have the damper completely

 

 

closed for ignition to take place. After there is a flame, the damper

 

 

can then be adjusted for the desired feed setting.

 

 

 

2.

Blockage in igniter tube or inlet for igniter tube.

Find the igniter housing on the backside of the firewall. The air

 

 

intake hole is a small hole located on bottom side of the housing.

 

 

Make sure it is clear. Also, look from the front of the stove to make

 

 

sure there is not any debris around the igniter element inside of the

 

 

igniter housing.

 

 

 

3.

The burnpot is not pushed completely to the rear of the firebox.

Make sure that the air intake collar on the burnpot is touching the

 

 

rear wall of the firebox.

 

 

 

4.

Bad igniter element.

Put power directly to the igniter element. Watch the tip of the igniter

 

 

from the front of the stove. After about 2 minutes the tip should

 

 

glow. If it does not, the element is bad.

 

 

 

5.

The control board is not sending power to the igniter.

Check the voltage going to the igniter during startup. It should be a

 

 

full current. If the voltage is lower than full current, check the wiring.

 

 

If the wiring checks out good, the board is bad.

 

 

 

 

SMOKE SMELL COMING BACK INTO THE HOME

 

 

 

Possible Causes:

Possible Remedies:

 

 

 

1.

There is a leak in the vent pipe system.

 

 

 

Inspect all vent pipe connections. Make sure they are sealed with

 

 

RTV silicone that has a temperature rating on 500 degree F or

 

 

higher. Also, seal joints with UL-181-AP foil tape. Also, make sure

 

 

the square to round adapter piece on the combustion blower has

 

 

been properly sealed with the same RTV.

 

 

 

2.

The gasket on the combustion blower has gone bad.

 

 

 

Inspect both gaskets on the combustion blower to make sure they

 

 

are in good shape.

 

 

 

 

CONVECTION BLOWER SHUTS OFF AND COMES BACK ON

 

 

 

Possible Causes:

Possible Remedies:

 

 

 

1.

The convection blower is overheating and tripping the internal

Try lubricating the convection blower. Put 1-2 drops of SAE 20 oil in

 

temperature shutoff.

each of the two oiling ports. Also, clean any dust off of the windings

 

 

and fan blades. If oiling the blower does not help, the blower may

 

 

be bad.

 

 

 

2.

Circuit board malfunction.

Test the current going to the convection blower. If there is power

 

 

being sent to the blower when it is shut off, then the control board is

 

 

fine. If there is NOT power being sent to the blower when it shuts off

 

 

during operation, then you have a bad control board.

 

 

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Economy Series P22 Introduction Important InformationSafety Precautions Table of Contents Installation SpecificationsPreparation ClearancesWhen Outside AIR is not Used Combustion AIR SupplyVenting Freestanding Installations Equivalent Vent Length EVLAssembling Pedestal or LEG SET Horizontally Through Wall refer to FigureVertically with NEW Chimney System Refer to Figure Vertically Into Existing Chimney SystemInstallation Through Side of Masonry Chimney Vertically Into Existing Masonry FireplaceInsert Installations Assembling the Flashing SETWhen Vent Pipe Extends to Chimney TOP Refer to Figures 16 Chase dimensions shown are minimums and must be maintained AS a BUILT-IN FireplaceElectrical Installation Special Mobile Home RequirementsCombustion AIR Supply Operation Proper Fuel PRE-START-UP CheckBuilding a Fire Hotrod Automatic FirestarterBreckwell Maintenance Tool Shutdown ProcedureSafety Features RE-STARTING a Warm StoveThermostat Installation Thermostat InstallationOptional Thermostat ∙ a Millivolt Thermostat is RequiredPlease Read this Maintenance CleaningASH Removal ASH DisposalBlowers Chimney Cleaning Daily Weekly Annually or per TonTroubleshooting Guide Stove Shuts OFF and the # 2 Light FlashesPossible Causes Stove Shuts OFF and the # 3 Light Flashes Stove Feeds PELLETS, but will not Ignite Possible Causes Possible RemediesSmoke Smell Coming Back Into the Home Convection Blower Shuts OFF and Comes Back onTroubleshooting Guide Troubleshooting Guide High Limit Switch Keeps Tripping Heat Level Setting P22Smoke Smell or Soot BUILD-UP Digital Circuit Board Timing RatesElectrical Diagram Replacement Parts BurnpotLifetime Limited Warranty
Related manuals
Manual 29 pages 58.71 Kb

P22FSL, P22I specifications

Breckwell has established itself as a key player in the realm of pellet stoves, with its P22 series being a testament to its commitment to innovation, efficiency, and user comfort. The P22I, P22FSL, and P22FSA models each boast unique features, yet all are designed with the same high-quality standards that Breckwell is known for.

The Breckwell P22I is an Intelligent pellet stove that stands out for its sleek design and exceptional heating capacity. It delivers up to 50,000 BTUs, making it suitable for larger spaces while ensuring efficient heat distribution. One of its main features is the intuitive digital control board with advanced programming options, allowing users to set their desired temperature and heating schedules effortlessly. The P22I also supports an optional direct vent system, increasing safety by minimizing the risk of backdrafts and ensuring proper exhaust flow.

The P22FSL model showcases a more modern aesthetic with its large viewing window, allowing users to enjoy the mesmerizing flames of the fire while heating their homes. Its side-loading feature offers convenience when it comes to refilling pellets. The P22FSL also incorporates a powerful blower to enhance heat circulation throughout the room. Furthermore, it features an adjustable heat output, providing users with the ability to customize their heating experience based on their preferences.

For those seeking a more traditional look, the P22FSA provides a classic yet efficient design. This model is perfect for homes that emphasize a more rustic charm while still delivering all the benefits of a modern pellet stove. Like its counterparts, the P22FSA provides robust heating capabilities of up to 50,000 BTUs. It also features a simple control panel, making it accessible for users of all technical backgrounds.

All three models utilize a reliable feed system that ensures a consistent flow of pellets, allowing for prolonged operational time before needing a refill. Additionally, they are equipped with safety features such as a thermal sensor and automatic shut-off to prevent overheating, offering peace of mind for users.

In terms of efficiency, the P22 series meets stringent EPA standards, making them environmentally friendly options for home heating. The use of premium materials in their construction ensures durability and longevity, making them a wise investment for homeowners looking to combine comfort with sustainability. Overall, the Breckwell P22I, P22FSL, and P22FSA models reflect the brand’s dedication to quality, comfort, and innovation in the pellet stove market.
Top Page Image Contents