Regency F37-NG, F37-LPG Horizontal Installations, Optional Components, Snorkel Terminations

Page 10

INSTALLATION

RESIDENTIAL AND MANUFACTURED HOMES /

MOBILE HOMES INSTALLATIONS

You will require the following components with your new Regency® Rear Flued Room Sealed Freestanding Gas Stove. Please review your product to make sure you have everything you need. In the event that you are missing any part, contact your dealer.

Note: These are the minimum pieces required.

Other parts may be required for your particular installation.

Minimum components for a Horizontal Installation:

946-112 Horizontal Termination Kit which includes:

16-5/8" dia. x 18" (168mm dia. x 457mm) Black Pipe

14" dia. x 18" (102mm dia. x 457mm) Aluminum Flue

1Astro Riser Vent Terminal

1Wall Penetration Heat Shield for Heat Sensitive walls (Wall Thimble) (2 pcs)

1Decorative Wall Trim (Black)

1Tube Mill-Pac

 

Screws

Optional Components:

946-204

45o Elbow - 6-5/8" (168mm) Black pipe

 

and 4" (102mm) Aluminum Flue

946-205

Vinyl Siding Shield for Riser Vent

 

Terminal

946-208/P

Flue Guard

940

Square Wall Thimble Cover*

942Wall Penetration Heat Shield*

* Simpson Dura-Vent components

HORIZONTAL INSTALLATIONS

1) Set the unit in its desired location. Check to

determine if wall studs are in the way when

the fl ueing system is attached. If this is the

case, you may want to adjust the location

of the unit.

2) Assemble the desired combination of pipe

and elbow to the appliance adapter with pipe

seams oriented down. Offset the pipe seams

as double seams in one place will cause the

outer pipe to take an oval shape. Kit comes

complete with 18" (457mm) of straight fl ue

- 6-5/8" (168mm) dia. black outer pipe and

4" (102mm) dia. inner fl ue.

c)Snorkel Terminations:

For installations requiring a vertical rise on the exterior of the building,Astro Riser Vent Terminations as shown in Dia. 2 is available. Follow the same installa- tion procedures as used for standard Horizontal Termination.

NEVERinstalltheAstroRiserventupside down.

3) With the pipe attached to the stove, slide

the stove into its correct location, and mark

the wall for a 9-1/2" (241mm) (inside

dimensions) round hole. The center of the

round hole should line up with the centerline

of the horizontal pipe, as shown in diagram

1. Cut and frame the 9-1/2 (241mm) round

hole in the exterior wall where the fl ue will

be terminated. If the wall being penetrated is

constructedofnon-combustiblematerial,i.e.

masonry block or concrete, a 7" (178mm)

diameter hole is acceptable.

Diagram 1

Note:

a)The horizontal run of fl ue should have a 1/4 inch (6mm) rise for every 1 foot (305mm) of run towards the termination. Never allow the fl ue to run downward. This could cause high temperatures and may present the possibility of a fi re.

b)The location of the horizontal fl ue ter- mination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. See the diagram in the "External Flue Termination Locations" section.

Diagram 2

*Diagram 2: Local codes or regulations may require different clearances.

10

F37 Regency® Rear Flued Room Sealed Freestanding Gas Heater

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual Please Keep These Instructions For Future ReferenceTo the New Owner Table of Contents Data Badge General Safety Information InstallationSpecifications Before YOU StartLocating Your Regency GAS Stove Installation ChecklistClearances to Combustibles Exterior Flue Termination Locations Clearance k in mmPlanning Your Flueing Installation Flueing Installation PrecautionsSafety Precautions For the Installer FlueingStraight Vertical Terminations Vertical Terminations Using Dura-Vent Flueing SystemFlueing Arrangements Vertical Terminations Offset to Vertical TerminationsOptional Components Horizontal InstallationsSnorkel Terminations Below Grade Snorkel Installation Hint Apply sealant to female endVertical Termination with CO-LINEAR Flex System GAS ConnectionConversion Kit Contains Qty Description LOG SET Installation Aeration AdjustmentNG 10mm open LPG 10mm open Door Installation Packaged Separately GAS Pipe Pressure TestingLouvre Installation Optional Wall ThermostatThermostat Wire Table Optional Remote ControlWiring Final CheckOperating Instructions For Your Safety Read Before Lighting Copy of the Lighting Plate InstructionsMaintenance Installing Glass Latch AdjustmentGlass Replacement Never operate your unit with broken glassTo remove fan FAN MaintenanceRemoving Valve Replacing FanMaintenance Parts List Main AssemblyBurner & LOG Assembly Door Assemblies Exclusions WarrantyConditions General

F37-LPG, F37-NG specifications

The Regency F37-LPG and F37-NG are contemporary gas fireplaces that represent a perfect blend of modern design and efficiency, catering to both propane (LPG) and natural gas (NG) needs. These models are engineered to enhance living spaces while providing optimal warmth and comfort. Their elegant appearance and advanced technologies make them a popular choice for homeowners seeking an aesthetically pleasing and functional heating solution.

One of the key features of the Regency F37 series is its large viewing area, which allows for an unobstructed view of the flames, creating a visually stunning focal point in any room. The fireplace's design includes a clean front and minimalistic aesthetics that can complement various interior styles, from traditional to contemporary. The F37 offers an array of customizable options, including various finishes, decorative media, and fireplace configurations.

Technologically, the Regency F37 is equipped with an advanced burner system that enhances the flame presentation while maintaining high efficiency. The system produces realistic flames and glowing embers, emulating the look of a traditional wood-burning fire without the hassle of real wood. Additionally, the fireplaces feature a precise control system, allowing users to adjust the flame height and heat output according to their preferences.

In terms of efficiency, the F37 series boasts impressive energy ratings, ensuring that homeowners can enjoy warmth without incurring excessive costs. The fireplaces are designed with an emphasis on heat retention, utilizing modern insulation and venting technologies that promote optimal performance. With a focus on environmental sustainability, Regency ensures that their units produce lower emissions, making the F37 series an eco-friendly choice for heating.

The ease of installation is another significant advantage of the Regency F37, with flexible venting options designed to accommodate various home layouts. Whether it is an existing space or a new construction, the fireplace can be adapted to meet specific design and functionality needs.

In summary, the Regency F37-LPG and F37-NG are exceptional gas fireplaces that combine striking design with cutting-edge technology. Their large viewing areas, customizable options, high efficiency, and eco-friendly features make them an excellent addition to any home, ensuring comfort and style for years to come.
Top Page Image Contents