Regency F37-NG Flueing Installation Precautions, Safety Precautions For the Installer

Page 8

INSTALLATION

FLUEING

The Regency® Room Sealed System (Horizon- tal Termination Kit (946-112) and the Vertical Termination with the Co-linear Flex System in combination with the REGENCYRoom Sealed- Rear Freestanding Gas Stoves (F37-NG and F37-LPG) have been approved and listed as Room Sealed heater systems by Australian Gas Association.

The Horiz. Termination Kit (946-112) includes everything required for a straight through the wall installation, or add a 45o elbow for a corner installation.

IMPORTANT

Read all instructions carefully before starting the installation. Failure to follow these instruc- tions may create a fi re or other safety hazard, and will void the warranty. Be sure to check the

flueing and clearance to combustible require- ments in "Locating Your Regency Gas Stove" to "Flueing Installation Precaution" sections. Consult your local building codes before begin- ning installation.

Thelocationoftheterminationcapmustconform tothediagramsinthe"ExteriorFlueTerimination Locations" section.

FLUEING

INSTALLATION

PRECAUTIONS

The Regency® Room Sealed System and the Vertical Termination with the Co-linear Flex Systemare engineeredproductsthathavebeen designed and tested for use with the F37-NG, and F37-LPG. The Regency® warranty will be voided and serious fi re, health or other safety hazards may result from any of the following actions:

1)Installation of any damaged Room Sealed component

2)Unauthorized modifi cation of the Room Sealed System

3)Installation of any component part not manufactured or approved by Regency® Industries Ltd.

4)Installation other than as instructed by Regency® Industries Ltd.

Warning:Always maintain required clearances (air spaces) to nearby combustibles to prevent a fire hazard. Do not fill air spaces with insulation.

The minimum clearance requirements between the outer wall of the fl ue pipe and nearby com- bustible surfaces is 30mm. Be sure to check the fl ue termination clearance requirements from decks, windows, soffi ts, gas regulators, air supply inlets and public walkways as specified in the"ExteriorFlueTerminationLocations"section and in your local building codes.

The gas appliance and flue system must be flued directly to the out- side of the building, and never be attached to a chimney serving a separate solid fuel or gas-burning appliance.

Each Room Sealed gas appliance must use its own separate fl ue system. Common fl ue systems are prohibited.

SAFETY PRECAUTIONS

FOR THE INSTALLER

1)Wear gloves and safety glasses for protec- tion.

2)Exercise extreme caution when using lad- ders or on roof tops.

3)Be aware of electrical wiring locations in walls and ceilings.

PLANNING YOUR FLUEING INSTALLATION

Seethe"ExteriorFlueTerminationLocations" section for requirements.

When planning your installation, it will be nec- essary to select the proper length of fl ue pipe for your particular requirements. Determine the minimum clearance to combustibles from the rear of the unit to the wall. It is also important to note the wall thickness. Before cutting the fl ue hole through the wall ensure that ALL fl ue and termination clearances (see the "Exterior Flue Termination Locations" section) will be met.

NOTE: Ensure compliance with the outside

flue terminal location before cutting hole as both dimensions must be met.

*If this is an outside corner, the minimum distance between the fl ue and the outside corner is 12" (30cm). See "F" on the diagram in the "Exterior Flue Termination Locations" section.

For corner installation, Restrictor must

For straight rear installation, Restrictor

be set at 1-1/4" open.

must be set at 1-1/8" open.

8

F37 Regency® Rear Flued Room Sealed Freestanding Gas Heater

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Manual Please Keep These Instructions For Future ReferenceTo the New Owner Table of Contents Data Badge Installation SpecificationsGeneral Safety Information Before YOU StartClearances to Combustibles Installation ChecklistLocating Your Regency GAS Stove Exterior Flue Termination Locations Clearance k in mmFlueing Installation Precautions Safety Precautions For the InstallerPlanning Your Flueing Installation FlueingVertical Terminations Using Dura-Vent Flueing System Flueing Arrangements Vertical TerminationsStraight Vertical Terminations Offset to Vertical TerminationsSnorkel Terminations Horizontal InstallationsOptional Components Below Grade Snorkel Installation Hint Apply sealant to female endVertical Termination with CO-LINEAR Flex System GAS ConnectionConversion Kit Contains Qty Description NG 10mm open LPG 10mm open Aeration AdjustmentLOG SET Installation Door Installation Packaged Separately Testing Louvre InstallationGAS Pipe Pressure Optional Wall ThermostatOptional Remote Control WiringThermostat Wire Table Final CheckOperating Instructions For Your Safety Read Before Lighting Copy of the Lighting Plate InstructionsMaintenance Latch Adjustment Glass ReplacementInstalling Glass Never operate your unit with broken glassFAN Maintenance Removing ValveTo remove fan Replacing FanMaintenance Parts List Main AssemblyBurner & LOG Assembly Door Assemblies Warranty ConditionsExclusions General

F37-LPG, F37-NG specifications

The Regency F37-LPG and F37-NG are contemporary gas fireplaces that represent a perfect blend of modern design and efficiency, catering to both propane (LPG) and natural gas (NG) needs. These models are engineered to enhance living spaces while providing optimal warmth and comfort. Their elegant appearance and advanced technologies make them a popular choice for homeowners seeking an aesthetically pleasing and functional heating solution.

One of the key features of the Regency F37 series is its large viewing area, which allows for an unobstructed view of the flames, creating a visually stunning focal point in any room. The fireplace's design includes a clean front and minimalistic aesthetics that can complement various interior styles, from traditional to contemporary. The F37 offers an array of customizable options, including various finishes, decorative media, and fireplace configurations.

Technologically, the Regency F37 is equipped with an advanced burner system that enhances the flame presentation while maintaining high efficiency. The system produces realistic flames and glowing embers, emulating the look of a traditional wood-burning fire without the hassle of real wood. Additionally, the fireplaces feature a precise control system, allowing users to adjust the flame height and heat output according to their preferences.

In terms of efficiency, the F37 series boasts impressive energy ratings, ensuring that homeowners can enjoy warmth without incurring excessive costs. The fireplaces are designed with an emphasis on heat retention, utilizing modern insulation and venting technologies that promote optimal performance. With a focus on environmental sustainability, Regency ensures that their units produce lower emissions, making the F37 series an eco-friendly choice for heating.

The ease of installation is another significant advantage of the Regency F37, with flexible venting options designed to accommodate various home layouts. Whether it is an existing space or a new construction, the fireplace can be adapted to meet specific design and functionality needs.

In summary, the Regency F37-LPG and F37-NG are exceptional gas fireplaces that combine striking design with cutting-edge technology. Their large viewing areas, customizable options, high efficiency, and eco-friendly features make them an excellent addition to any home, ensuring comfort and style for years to come.
Top Page Image Contents