Below Grade Snorkel Installation

INSTALLATION

NOTE: For Snorkel terminations in ABOVE grade installations, follow national or local code requirements.

If the Snorkel Termination must be installed below grade, i.e. basement application, properdrainagemustbeprovidedtoprevent waterfromenteringtheSnorkelTermination. Refer to Dura-Vent Installation instructions for details.. Do not attempt to enclose the Snorkel within the wall, or any other type of enclosure.

4)Install wall penetration heat shield in the center of the 9-1/2" round hole and attach with wood screws. The four wood screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings. Diagram 3.

Diagram 3

5)If installing termination on a siding covered wall, a vinyl siding standoff or furring strips must be used to ensure that the termination is not recessed into the siding. Diagram. 3.

6)Take the Riser Vent terminal and separate the Backing Plate from the Riser Vent Front by removing 8 screws as shown in diagram 4.

7)Install the Backing Plate into the wall penetration heat shield and attach using 4 screws. Diagram 4.

8)Connect all pipe sections to unit and install into wall:

a)Measure pipe length required and cut to length. Hint: use the cut end of the 6-5/8" dia. outer pipe at the ﬂ ue terminal end.

b)Push the pipe sections completely together, the minimum pipe overlap is 1-1/4". Secure all outer pipe joints by using at least two screws. Locate the screws at the bottom of the pipe so that the screw heads are hidden on the ﬁ nal installation. Apply seal- ant "Mill-Pac" to inner pipe and high temp silicone sealant or "Mill-Pac" to outer pipe on every joint.

Hint: Apply sealant to female end.

c)Before connecting the ﬂ ue pipe to the ﬂ ue termination, slide the black decorative wall thimble cover over the ﬂ ue pipe, then slide the Wall Penetration Heat Shield (Part # 946-202)overtheﬂuepipe.Diagram 3.

d)Slide the appliance and ﬂ ue assem- bly towards the wall carefully insert- ing the ﬂ ue pipe into the riser vent terminal assembly. It is important that the ﬂ ue pipe extends into the Riser Vent Backing Plate a sufﬁcient distancesoastoresultinaminimum pipe overlap of 1-1/4 inches. Secure theconnectionbetweentheﬂuepipe and the ﬂue cap by attaching the two sheet metal strips extending from the Riser Vent Backing Plate into the outer wall of the ﬂ ue pipe. Use two aluminum screws provided to con- nect the strips to the pipe section. Bend any remaining portion of the sheet metal strip back towards the ﬂue cap and cut off any excess, it will be concealed by the decorative wall thimble cover. See diagram 5.

8)Slide the decorative wall thimble up to the wall surface being careful not to scratch the paint. See diagram 5.

Diagram 5

9)Back outside: Apply sealant to the 4" inner ﬂ ue and slide the Riser Vent Front into the Backing Plate and fasten with 8 screws.

IMPORTANT:

When connecting the pipe to the Riser Vent, apply Mill-Pac to the inner pipe on theRiserVentTerminal,aroundthebead. Ensure that the ﬂue pipe is pushed past the bead for a secure ﬁt.

10)Seal around the outer edge of the Riser Vent Backing Plate.

Diagram 4

F37 Regency® Rear Flued Room Sealed Freestanding Gas Heater

F37-LPG, F37-NG specifications

The Regency F37-LPG and F37-NG are contemporary gas fireplaces that represent a perfect blend of modern design and efficiency, catering to both propane (LPG) and natural gas (NG) needs. These models are engineered to enhance living spaces while providing optimal warmth and comfort. Their elegant appearance and advanced technologies make them a popular choice for homeowners seeking an aesthetically pleasing and functional heating solution.

One of the key features of the Regency F37 series is its large viewing area, which allows for an unobstructed view of the flames, creating a visually stunning focal point in any room. The fireplace's design includes a clean front and minimalistic aesthetics that can complement various interior styles, from traditional to contemporary. The F37 offers an array of customizable options, including various finishes, decorative media, and fireplace configurations.

Technologically, the Regency F37 is equipped with an advanced burner system that enhances the flame presentation while maintaining high efficiency. The system produces realistic flames and glowing embers, emulating the look of a traditional wood-burning fire without the hassle of real wood. Additionally, the fireplaces feature a precise control system, allowing users to adjust the flame height and heat output according to their preferences.

In terms of efficiency, the F37 series boasts impressive energy ratings, ensuring that homeowners can enjoy warmth without incurring excessive costs. The fireplaces are designed with an emphasis on heat retention, utilizing modern insulation and venting technologies that promote optimal performance. With a focus on environmental sustainability, Regency ensures that their units produce lower emissions, making the F37 series an eco-friendly choice for heating.

The ease of installation is another significant advantage of the Regency F37, with flexible venting options designed to accommodate various home layouts. Whether it is an existing space or a new construction, the fireplace can be adapted to meet specific design and functionality needs.

In summary, the Regency F37-LPG and F37-NG are exceptional gas fireplaces that combine striking design with cutting-edge technology. Their large viewing areas, customizable options, high efficiency, and eco-friendly features make them an excellent addition to any home, ensuring comfort and style for years to come.