Regency C33-NG3, C33-LP3 Clearances to Combustibles, Optional FAN Installation, This includes

Page 7

INSTALLATION

This includes:

1)Clocking the appliance to ensure the correct fi ring rate (rate noted on label) after burning appliance for 15 minutes.

2)If required, adjusting the primary air to ensure that the fl ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

3)Check for proper draft.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

CLEARANCES TO

COMBUSTIBLES

The clearances listed below are MINIMUM distances. Measure the clearance to both the appliance and the chimney connector. The far- thest distance is correct if the two clearances do not coincide. For example, if the appliance is set as indicated in one of the diagrams but the back wall is too close, move the stove until the correct clearance to the back wall is obtained.

This unit can be installed on a solid combustible surface like a wood fl oor. This unit can also be installed directly on carpeting or vinyl when the bottom pedestal cover plate (provided with the unit) is installed.

OPTIONAL FAN

INSTALLATION

Important: Disconnect the power supply before installation or serv- icing.

For pedestal unit: To install the fan in an in- stalled stove-access from front through the pedestal by following the directions below. If the stove is not installed - access through rear and follow steps 4 to 17.

For leg unit: remove 7 screws, remove bottom access panel and install fan assembly and follow steps 4 to 17.

1)Open pedestal door and remove door cover plate by removing 4 screws. See diagram 1.

4)Screw the four 8-32 x 3/4 screws provided into the nutserts as shown in diagram 3. Do not tighten screws.

5)Push all the fan wires through the hole on the fan assembly. See diagram 2

.

6)Putpowercord(shownindiagram3)through the hole and pull through to front of unit for easier installation of ground wire.

7)Place fan assembly partially in door cover plate hole. See diagram 2.

8)Attach the 2 ground wires (green) to the ground lug as per diagram 2.

Note:Ground lug is located on the bottom of the fan assembly. See diagram 2.

This appliance may be installed only with the clearances as shown in the situations pictured. Do not combine clearances from one type of installation with another in order to achieve closer clearances. Use the minimum clearances shown in the diagrams. Alcove installations are approved, as long as side wall clearances are maintained.

C33-3 Clearances to Combustibles

A

Side Wall to Unit

10" / 250 mm

B

Back Wall to Unit

6" / 150 mm

E

Side Wall to Unit

1.5" / 38 mm

 

 

 

C33-3 Reference Dimensions

 

 

to Flue Centerline

C

Back Wall

11-1/2"/ 292 mm

D

Side Wall

22" / 559 mm

F

Side Wall

13" / 330 mm

Minimum ceiling height is 36" / 914 mm from

Diagram 3

9) Lift the fan assembly in through the pedestal and up through the cut out as shown in diagrams 3 and 4.

10) Put the insulation gasket on the back of the fan. Line up the keyhole slots with the matching screws and pull back slightly to lock into place. While holding fan assembly in place, tighten screws.

Diagram 1

2)Remove valve cover plate by removing 2

screws.

3) Remove wire from piezo ignitor.

Diagram 4

Diagram 2

Regency® CLASSIC C33-3 Freestanding Gas Stove

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents C33 Classic Freestanding Gas Stove To the New Owner Table of Contents Safety Label MA Code CO Detector RequirementsBefore YOU Start InstallationGeneral Safety Information Installation ChecklistThis includes Optional FAN InstallationC33-3 Reference Dimensions Clearances to CombustiblesWiring Pedestal AssemblyDraft Hood Optional Outside AIRVenting High Elevation GAS Pipe Pressure TestingGAS Connection System DataWith Bottom Shield Installation DC SparkerValve With PedestalOperation Test for LOG SET Flue Spillage InstallationWall Thermostat Installation Safety LatchRemote Control Installation Remote Wall SwitchWiring Diagrams Normal Operating Sounds of GAS Appliances Do Not Attempt To Clean The Glass While It is still hot Shutdown ProcedureOperating Instructions Copy of the Lighting Plate Instructions For Your Safety Read Before LightingPilot Adjustment MaintenanceGeneral Vent Maintenance Aeration AdjustmentGOLD-PLATED Doors LOG ReplacementGlass Replacement Clean any fingerprints off before turning the unit onInstalling Removing Valve AssemblyTo remove valve from valve assembly, continue Main Assembly Parts ListBurner & Logs Base Options Regency Classic C33-3 Freestanding Gas Stove Regency Classic C33-3 Freestanding Gas Stove Regency Classic C33-3 Freestanding Gas Stove Conditions WarrantyInstaller Please complete the following information

C33-NG3, C33-LP3 specifications

The Regency C33-NG3 and C33-LP3 are advanced gas fireplaces that reflect both elegance and functionality, making them ideal choices for those looking to enhance their living spaces. These models stand out in the market due to their exceptional design and innovative technology, catering to both natural gas and propane options.

One of the main features of the Regency C33-NG3 and C33-LP3 is their impressive heating capacity. Both models boast an efficiency rating that competently warms your space while maintaining eco-friendly operations. This makes them an attractive option for homeowners seeking a blend of luxury and sustainable heating solutions.

Both fireplace models are designed with a modern aesthetic, featuring a sleek front and expansive viewing area that allows the warm glow of flames to be the centerpiece of any room. With customizable trim options and the ability to add decorative media such as stones or glass, these fireplaces can be tailored to fit various interior designs. The contemporary linear design not only offers visual appeal but also maximizes the heat output, ensuring a cozy environment.

In terms of technology, the Regency C33-NG3 and C33-LP3 come equipped with an advanced electronic ignition system. This feature allows for easy lighting of the fireplace with the push of a button, eliminating the hassle associated with traditional ignition methods. Additionally, these models include a thermostatic control option, enabling users to maintain their desired temperature effortlessly.

The patented heat exchanger technology enhances the overall efficiency of both models, ensuring that the heat produced is directed into the room rather than being lost through the venting system. This innovative design contributes to a more efficient heating experience, making these fireplaces a cost-effective choice for consumers.

Safety is also a priority with the Regency C33-NG3 and C33-LP3. Both models incorporate safety barriers and advanced flame sensing technology, ensuring peace of mind during operation. The sleek glass front not only adds to the aesthetic but also keeps flames safely contained, making them suitable for families with children or pets.

In conclusion, the Regency C33-NG3 and C33-LP3 combine modern elegance with advanced heating technology. Their efficient heating capabilities, customizable designs, and user-friendly features make them standout choices for anyone looking to elevate their home’s ambiance while ensuring warmth and comfort.
Top Page Image Contents