Operating Instructions, Shutdown Procedure

OPERATING INSTRUCTIONS

OPERATING

INSTRUCTIONS

LIGHTING MAINTENANCE

PROCEDURE INSTRUCTIONS

1)The FIRST FIRE in your stove is part of the paintcuringprocess.Toensurethatthepaint is properly cured, it is recommended that you burn your ﬁ replace for at least four (4) hours the ﬁ rst time you use it with the fan on. When ﬁ rst operated, the unit will release an odour caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a coupleofhours.Theglasspanelmayrequire cleaning.

Do Not Attempt To Clean The Glass While

it is still hot!

Note: When the glass is cold and the appli- ance is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.

DO NOT BURN THE APPLIANCE WITHOUT THE GLASS FRONT IN PLACE.

2)Read and understand these instructions before operating this appliance.

3)Check to see that all wiring is correct and enclosed to prevent possible shock.

4)Check to ensure there are no gas leaks.

5)Make sure the glass in the door frame is properly positioned. Never operate the ap- pliance with the glass removed.

6)Verify that the venting is unobstructed.

7)Verify log placement. If the pilot cannot be seen when lighting the unit - the logs have been incorrectly positioned.

8)The unit should never be turned off, and on again without a minimum of a 60 second wait for purging.

NOTE: For all propane units and units equipped with electric spark boxes, see "Copy of Lighting Plate Instruc- tions" section for more details.

IMPORTANT: Gas on/off knob cannot be turned from "PILOT" to "OFF" unless it is partially depressed.

1)Turn burner OFF using "ON/OFF" switch.

2)Turn gas control knob so indicator points to "OFF" position and allow 5 minutes for any gas in the combustion chamber to escape.

3)Turn gas control knob counterclockwise so indicator points to the "PILOT" position. Depress the gas control knob fully. Depress the igniter button several times until the pilot lights. After approximately one minute, release the gas control knob.The pilot ﬂame should continue to burn. If the pilot does not remain lit, repeat operation allowing a longer period before releasing gas control knob.

4)When the pilot stays lit, turn the gas knob further counterclockwise to the "ON" posi- tion.

5)UsetheON/OFFswitch,wallswitch,thermo- stat or remote control to turn on the unit.

6)Rotate the ﬂ ame height regulator (Hi/Lo) to adjust the ﬂ ame height higher or lower.

SHUTDOWN

PROCEDURE

1)Use the "ON/OFF" switch, wall switch, thermostat or remote control to turn off the burner.

2)Push in the PILOT knob slightly and turn clockwise to "OFF". Do not force.

3)Turn off all electric power to the appliance if service is to be performed.

1)Alwaysturnoffthegasvalvebeforecleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year.

When cleaning the logs, use a soft clean brush as the logs are fragile and easily damaged.

2)Clean appliance and door with a damp cloth (never when unit is hot). Never use an abrasive cleaner. The glass should be cleaned with a gas ﬁ replace glass cleaner (when it starts to cloud up).

3)The heater is ﬁ nished in a heat resistant paint and should only be reﬁ nished with heat resistant paint. Regency® uses Stove Brite Paint - Metallic Black #6309.

4)Make a periodic check of burner for proper position and condition. Visually check the ﬂame of the burner periodically, making sure the ﬂ ames are steady; not lifting or ﬂ oating. If there is a problem, call a qualiﬁ ed service person.

5)The appliance and venting system must be inspected before use, and at least annually, by a qualiﬁ ed ﬁ eld service person, to ensure that the ﬂ ow of combustion and ventilation air is not obstructed.

During the annual service call, the burners should be removed from the burner tray and cleaned. Replace the embers and rock wool.

6)Each time the appliance is lit, it may cause condensation and fog the glass. This con- densation is normal and will disappear in a few minutes as the glass heats up.

7)Caution: Label all wires prior to discon- nection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLYSUPERVISEDWHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.

16	Regency® CLASSIC C33-3 Freestanding Gas Stove

C33-NG3, C33-LP3 specifications

The Regency C33-NG3 and C33-LP3 are advanced gas fireplaces that reflect both elegance and functionality, making them ideal choices for those looking to enhance their living spaces. These models stand out in the market due to their exceptional design and innovative technology, catering to both natural gas and propane options.

One of the main features of the Regency C33-NG3 and C33-LP3 is their impressive heating capacity. Both models boast an efficiency rating that competently warms your space while maintaining eco-friendly operations. This makes them an attractive option for homeowners seeking a blend of luxury and sustainable heating solutions.

Both fireplace models are designed with a modern aesthetic, featuring a sleek front and expansive viewing area that allows the warm glow of flames to be the centerpiece of any room. With customizable trim options and the ability to add decorative media such as stones or glass, these fireplaces can be tailored to fit various interior designs. The contemporary linear design not only offers visual appeal but also maximizes the heat output, ensuring a cozy environment.

In terms of technology, the Regency C33-NG3 and C33-LP3 come equipped with an advanced electronic ignition system. This feature allows for easy lighting of the fireplace with the push of a button, eliminating the hassle associated with traditional ignition methods. Additionally, these models include a thermostatic control option, enabling users to maintain their desired temperature effortlessly.

The patented heat exchanger technology enhances the overall efficiency of both models, ensuring that the heat produced is directed into the room rather than being lost through the venting system. This innovative design contributes to a more efficient heating experience, making these fireplaces a cost-effective choice for consumers.

Safety is also a priority with the Regency C33-NG3 and C33-LP3. Both models incorporate safety barriers and advanced flame sensing technology, ensuring peace of mind during operation. The sleek glass front not only adds to the aesthetic but also keeps flames safely contained, making them suitable for families with children or pets.

In conclusion, the Regency C33-NG3 and C33-LP3 combine modern elegance with advanced heating technology. Their efficient heating capabilities, customizable designs, and user-friendly features make them standout choices for anyone looking to elevate their home’s ambiance while ensuring warmth and comfort.