Regency U37-NG1, U37-LP1 Venting Installation Precautions, Safety Precautions For the Installer

Page 9

INSTALLATION

IMPORTANT

Read all instructions carefully before starting the installation. Failure to follow these instruc- tions may create a fi re or other safety hazard, and will void the warranty. Be sure to check the venting and clearance to combustible require- ments in "Clearances to Combustibles" to "Rigid Pipe Venting - Vertical Termination" sections. Consult your local building codes before begin- ning installation.

The location of the termination cap must con- form to the requirements in the" Exterior Vent Terminal Locations" section.

VENTING

INSTALLATION

PRECAUTIONS

The Regency® Direct Vent System and the Vertical Termination with the Co-linear Flex System are engineered products that have been designed and tested for use with the U37-NG1, and U37-LP1. The Regency® war- ranty will be voided and serious fi re, health or

other safety hazards may result from any of the following actions:

1)Installation of any damaged Direct Vent component

2)Unauthorized modification of the Direct Vent System

3)Installation of any component part not manufactured or approved by Regency® Industries Ltd.

4)Installation other than as instructed by Regency® Industries Ltd.

Warning: Always maintain required clearances (air spaces) to nearby com- bustibles to prevent a fire hazard. Do not fill air spaces with insulation.

The minimum clearance requirements between the outer wall of the vent pipe and nearby com- bustible surfaces is 1-1/4 inch. Be sure to check the vent termination clearance requirements from decks, windows, soffits, gas regulators, air supply inlets and public walkways as specifi ed in the "Exterior VentTerminal Locations" section and in your local building codes.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas-burning appliance.

Each direct vent gas appliance must use its own separate vent system. Common vent systems are prohibited.

SAFETY PRECAUTIONS

FOR THE INSTALLER

1)Wear gloves and safety glasses for protec- tion.

2)Exercise extreme caution when using lad- ders or on roof tops.

3)Be aware of electrical wiring locations in walls and ceilings.

PLANNING YOUR VENTING INSTALLATION

See the "Exterior Vent Terminal Locations" section for the requirements. .

When planning your installation, it will be nec- essary to select the proper length of vent pipe for your particular requirements. Determine the minimum clearance to combustibles from the rear of the unit to the wall. It is also important to note the wall thickness. Before cutting the vent hole through the wall ensure that ALL vent and termination clearances (see the "Exterior Vent Terminal Locations" section) will be met.

*If this is an outside corner, the minimum distance between the vent and the outside corner is 12" (30cm). See "F" on the diagram in the "Exterior Vent Terminal Locations" section.

For corner installation, Restrictor must

For straight rear installation, Restrictor

be set at 1-1/4" open.

must be set at 1-1/8" open.

NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.

U37-1 Regency® ULTIMATE Rear Vent Direct Vent Freestanding Gas Stove

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Ultimate U37 Rear Vent To the New Owner Information for MOBILE/MANUFACTURED Homes After First SaleTable of Contents Copy of Safety Label for U37 Safety LabelMA Code CO Detector RequirementsSpecifications InstallationGeneral Safety Information Important Message Save These InstructionsManufactured Mobile Home Additional Requirements Installation ChecklistClearances to Combustibles Locating Your GAS StoveExterior Vent Terminal Locations Venting Installation Precautions Safety Precautions For the InstallerPlanning Your Venting Installation SV4LB6 Rigid Pipe Venting Components ListStraight Vertical Terminations Using Rigid Piping SystemsOffset to Vertical Terminations Vent Restrictor PositionOptional Components Horizontal TerminationsAlternate Snorkel Termination Cap Snorkel TerminationsHint Apply sealant to female end Below Grade Snorkel InstallationVertical Termination with CO-LINEAR Flex System Required Parts DescriptionAlternate Approved Caps Approved for US Installations Only GeneralConverting a Factory Built Metal Chimney Converting Masonry Chimney Conversion Kit Contains Qty Conversion KIT# 514-969 from NG to LPInstallation of the DC Sparker Green ground wire LOG SET Installation Aeration AdjustmentGAS Connection High ElevationA02-65 Valve Description GAS Pipe Pressure TestingThermocouple Connection Ports on the valveOptional Remote Control Louver InstallationWall Thermostat Final CheckWiring Diagrams For Propane Units and Units Equipped with DC Spark Boxes Operating Instructions Blower Thermodisc Copy of the Lighting Plate InstructionsPilot Flame Gas Control ValveMaintenance Glass Replacement Latch AdjustmentInstalling Glass Removing GlassFAN Maintenance Removing ValveReplacing Fan Maintenance U37 Main Assembly Parts ListU37 Burner & LOG Assembly U37 Door Assemblies Conditions WarrantyInstaller Please complete the following information
Related manuals
Manual 36 pages 55.81 Kb

U37-LP1, U37-NG1 specifications

The Regency U37-NG1 and U37-LP1 are two innovative models that showcase advanced technology and superior engineering in the realm of HVAC (heating, ventilation, and air conditioning) systems. These units are designed to deliver optimal comfort while maximizing energy efficiency, making them ideal for both residential and commercial applications.

One of the standout features of the U37-NG1 is its use of a high-efficiency burner system, which ensures that every unit is capable of delivering substantial heating output while consuming minimal gas. This not only translates to lower utility bills for users but also aligns with sustainability goals by reducing carbon emissions. In terms of design, the U37-NG1 is compact and can be installed in a variety of settings, making it a versatile choice for many different environments.

The U37-LP1, on the other hand, is tailored for propane applications, making it perfect for areas where natural gas is inaccessible. It features a similar high-efficiency heating output, ensuring that it meets the demands of users without compromising on performance. The dual-fuel capability of the U37 series enhances its adaptability, allowing it to be used in a range of scenarios.

Both models are equipped with advanced control technologies, including programmable thermostats and smart connectivity features. Users can easily manage their heating systems through mobile apps, allowing for remote adjustments and real-time monitoring. This technology not only enhances user convenience but also promotes energy conservation by allowing users to adjust settings based on their lifestyle and preferences.

In terms of durability, the Regency U37 series boasts a robust construction designed to withstand various environmental conditions. With quality materials and expert craftsmanship, these units are built to last, reducing the need for frequent repairs or replacements.

Overall, the Regency U37-NG1 and U37-LP1 models combine cutting-edge technology with practical features to deliver an exceptional heating experience. Their commitment to energy efficiency, adaptability, and user-friendly controls positions them as leading options in the HVAC market, making comfortable living spaces more accessible while promoting environmentally responsible practices. Whether for home use or commercial properties, these systems offer reliability and performance tailored to the needs of modern users.
Top Page Image Contents