Regency U35-LP1 Door Glass, FAN Maintenance, Flush Glass Replacement, Bay Glass Replacement

Page 23

MAINTENANCE

Clean any fingerprints off before turning the unit on. If the top louvers start to discolour, check the door gasket seal and replace if necessary.

DOOR GLASS

Your FPI insert is supplied with high temperature, 5 mm Neoceram ceramic glass that will withstand the highest heat that your unit will produce. Do not abuse the glass by striking the surface or by slamming the door shut.

If your glass requires cleaning, we recommend using an approved glass cleaner available at all authorized dealers. Do not use abrasive materials. Do not clean the glass when hot.

In the event that you break your glass by impact, purchase your replacement from an authorized FPI dealer only, do not use substitute materials. Follow our step-by-step instructions for replacement. Caution: Wear gloves when removing damaged or broken glass.

Warning: Do not operate appliance with glass panels removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person.

Flush Glass Replacement

Remove the flush door front. Remove the 4 glass clips from each corner. Slide in the new replacement glass. Push the 4 glass clips back onto the frame.

Bay Glass Replacement

1)Remove the door from the unit and place on a soft surface to prevent scratching.

2)Remove the nuts holding the glass clips in place and remove.

3)Replace the glass. The glass must have gasketing around it.

5)Reverse the previous steps, replace the glass clips and fasten with the nuts but do not over tighten, as this can break the glass.

6)Replace door on the stove and check the seal.

2)Unplug or disconnect power source to stove.

3)Remove glass front (See the "Standard Flush Door" section).

4)Remove logs.

5)Remove brick panels, if used.

6)Straighten the adjustment wire under the firebox base.

Straighten adjustment wire.

7)Remove the Burner/Rear Log Support assembly by removing the 2 screws (1 on each side) and sliding the assembly to the left to free the bottom brackets from the screws on the firebox base.

Left Side Burner

Bracket

FAN MAINTENANCE

If your fan requires maintenance or replacement, access to the fan is through the plate on the floor of the firebox. NOTE: the unit MUST NOT be operated without the fan access panel securely in place.

Caution: Label all wires prior to disconnecting when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

To Remove Fan:

1)Turn the unit off and allow it to cool to room temperature.

Burner/Rear Log Support Assembly: After removing the screws slide to the left to remove the assembly from the firebox base.

8)Lift the Burner/Rear Log Support assembly up and away from the orifice.

Burner Orifice

Lift Burner/Rear Log Support assembly up

and away from the burner orifice.

9)Remove the 8 screws holding the Access Panel in place.

U35 FPI Direct Vent Gas Insert

23

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents U35 Gas Insert U35 FPI Direct Vent Gas Insert FPI GAS Fireplace InsertTable of Contents Safety Label MA Code CO Detector RequirementsInstallation Materials Required Installation ChecklistMinimum Fireplace Dimensions Minimum Clearances to Combustibles Venting Flue Liner InstallationGAS Connection SIT Valve Description GAS Pipe Pressure TestingGAS Insert Aeration System Optional Brick PanelHint Install the front right side first LOG InstallationFaceplate & Trim Installation Rear View Faceplate Assembly DiagramHinge Location Bottom Louver Standard Flush DoorOptional Flush Trim Flush LouversBAY Louvers Optional BAY DoorOptional BAY Trim Double Screen DoorsBlanking Plate Tabs Kensington Front Screw Kensington Front InstallationKensington Front Screws Glass Door Sub-Frame Hook Panel Door InstallationFull Screen Doors Hinge Wiring Diagrams Thermostat Optional Remote Control Optional WallOperating Instructions Normal Operating Sounds GAS Appliances Copy of Lighting Instruction PlateAutomatic Convection FAN Operation Maintenance Door Glass FAN MaintenanceFlush Glass Replacement Bay Glass ReplacementShut off the gas supply Removing ValveReplacing fan Left Valve Bracket Right Installing ValveMain Assembly Parts ListBurner & LOG Assembly Flush Front Flush Door and BAY Front AssemblyBay Front FACEPLATES, TRIMS, and Hearths Parts ListU35 FPI Direct Vent Gas Insert Conditions WarrantyInstaller Please complete the following information

U35-NG1, U35-LP1 specifications

The Regency U35-LP1 and U35-NG1 are cutting-edge gas fireplace inserts designed to elevate both the aesthetic and functional appeal of any home. Both models represent a blend of modern technology and classic design, making them perfect for those who desire warmth without sacrificing style.

One of the main features of the Regency U35 series is its impressive heat output. With the capability of delivering up to 30,000 BTUs, these inserts efficiently heat medium to large spaces, ensuring comfort even in the coldest months. The U35-LP1 operates on propane, while the U35-NG1 utilizes natural gas, providing flexibility in fuel choice based on the homeowner's needs.

Another distinctive characteristic of the U35 fireplace inserts is their large viewing area, featuring a panoramic glass front that maximizes the fire's visibility. This design is not only visually appealing but also adheres to safety standards, as the glass remains cool to the touch, making it suitable for households with children or pets. The flame presentation is further enhanced by the realistic logs and ember bed, creating an inviting ambiance that replicates a traditional wood-burning fire.

Technologically, these fireplaces are equipped with advanced features such as a programmable remote control, enabling users to adjust the flame height and heat output with ease. Additionally, the inserts come with an optional wall switch control, providing further convenience in managing the fire. Energy efficiency is another hallmark of the U35 series, as they meet or exceed the EPA's standards, ensuring minimal emissions and lower energy costs.

Installation is simplified thanks to the flexible venting options available with both models. Homeowners can choose from straight, horizontal, or vertical venting configurations, making it easier to integrate the fireplace into various home layouts. Furthermore, both models come with a limited lifetime warranty, reflecting Regency's commitment to quality and reliability.

In conclusion, the Regency U35-LP1 and U35-NG1 are exceptional gas fireplace inserts that combine aesthetic elegance with functional efficiency. With their impressive heat output, user-friendly controls, and stylish designs, they stand out as exceptional choices for anyone looking to enhance their living space with the warmth and charm of a beautiful fire.
Top Page Image Contents