Nimbus Water Systems MN-800-TF manual

Page 16

•Tag and disconnect the three tubing connections on the desalinator namely the feed, concentrate and product.

•Unsnap the desalinator retainers and pull desalinator(s) out.

•Remove retaining clips from ends of desalinator by tapping the open ends of the clips with a plastic or rawhide mallet until they are through the slots in the pressure vessel. Pull clips completely out of pressure vessel.

•Remove end plugs by gently pulling on the fittings. Do not use pliers on the fitting threads because the threads might get damaged. As a suggestion, attach a scrap piece of tubing (with a nut, a ferrule and an insert), and then use the tubing as a handle. See §8.0 PARTS & ACCESSORIES for end plug pulling tool.

•Push membrane out of pressure vessel from the feed end.

•Discard old membrane. Be careful not to discard the gray closed-end plug or the product inter-connector.

•Clean vessel and plugs with a mild detergent soap and rinse thoroughly.

•Inspect all O-rings for cracks or nicks, replace as necessary. Lubricate O-rings with an appropriate petroleum or silicone-based lubricant.

•Install new membrane into the feed end of vessel (in the direction shown in Figure 4). Be sure to note the end with the brine seal.

•Install closed-end plug into vessel feed end plug, and product inter-connector into the vessel concentrate/product end plug.

•Install end plugs into their proper ends. IF END PLUGS ARE INSTALLED ON THE WRONG ENDS THE SYSTEM WILL NOT OPERATE PROPERLY.

•Install retaining clips and mount desalinator onto frame using tabs and install the retaining clips.

•Connect feed, concentrate, and product lines to their proper ports.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents MN-800-TF Nimbus MN-800 TF Reverse Osmosis Treatment System §1.0 MN-800 TF System Specifications Model noPage Page Ancillary Equipment §3.0 PRE-INSTALLATION Procedures §3.1 Packaging§3.2 Operating Limitations §3.3 Operating Parameters§4.0 Installation §4.2 System Plumbing Installation Guide Lines§4.2.1 Tank Preparation and Installation §4.1 LocationPage §4.2.2 BY-PASS Panel Preparation and Installation §4.2.3 RO Feed Water Connection§4.2.3 RO Drain Connections §4.3 ElectricalPage §5.0 System Flush and Performance Verification Immediately§5.2.4 LOW Pressure Switch Test §5.2.5 Tank Pressure Switch Test§5.2.1 Flow Tests §5.2.2 Concentrate to Product Ratio§6.0 Operation and Maintenance §6.3 Quarterly Service§7.0 Service §7.1 LOW Pressure Switch Adjustment §6.1 Daily System Checks§7.2 Tank Pressure Switch Adjustment §7.3 Membrane Replacement see FigurePage Page §7.4 PRE Filter Carbon Cartridge Replacement §7.5 POST-FILTER Carbon Cartridge ReplacementPage §8.0 Parts and Accessories Housings§9.0 Attachments §9.1 Remote Bypass System Instructions Specifications §9.2 TDS Monitor Instructions§9.3 Warranty

MN-800-TF specifications

The Nimbus Water Systems MN-800-TF is an innovative water filtration system designed to provide homes with clean, safe, and great-tasting water. Emerging as a leading solution in the water purification market, the MN-800-TF stands out due to its advanced features and cutting-edge technologies that cater to diverse filtration needs.

One of the main features of the MN-800-TF is its multi-stage filtration process, which includes a combination of sediment filters, activated carbon, and reverse osmosis membranes. This multi-tier approach ensures that a wide range of impurities such as chlorine, heavy metals, sediments, and even microorganisms are effectively removed from the water. This results in not only improved taste but also enhanced safety for household consumption.

The system utilizes advanced filtration technologies, including a high-capacity reverse osmosis membrane that boasts an impressive rejection rate for dissolved solids. This technology ensures that the water retains essential minerals while eliminating harmful contaminants. The activated carbon filters are designed to reduce chlorine levels and volatile organic compounds, resulting in water that is pure and refreshing.

In terms of user convenience, the MN-800-TF is equipped with an easy-to-read digital display that provides real-time information regarding filter status and water quality. The system also features a simple, intuitive setup process and space-saving design, making it suitable for both small and large homes. The compact design allows for installation under sinks or in utility rooms, optimizing space without compromising efficiency.

Another notable characteristic of the MN-800-TF is its sustainable approach. The system is designed to produce minimal wastewater during the filtration process, which is a critical consideration given the rising concern over water conservation. Moreover, by using a reusable filter system, users can reduce plastic waste generated from traditional bottled water usage.

The Nimbus Water Systems MN-800-TF is also backed by robust customer support and a warranty, ensuring peace of mind for users. Overall, this water filtration system integrates advanced technology and user-friendly features, making it an optimal choice for anyone looking to enhance their home’s water quality. With its combination of efficiency, sustainability, and reliability, the MN-800-TF truly embodies the future of home water purification.
Top Page Image Contents