Nilfisk-ALTO C.A.V. 15 How To Install The Sandpaper, Sanding Cuts and Sandpaper, Initial Cut

Page 28

Figure 1

Figure 2

Figure 3

HOW TO PREPARE THE MACHINE FOR OPERATION

WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the sandpaper.

How To Install The Sandpaper

To install the sandpaper, follow this procedure:

1.Put the handle in the vertical position.

2.Lock the handle. To lock the handle, push the locking lever down. See figure 1.

3.Tilt the machine backward until the handle is on the floor.

4.Put one foot on each side of the machine.

5.Using a 7/8 wrench, remove the nut and the washer that hold the paper holder. See figure 2.

6.Put the sandpaper on the sanding pad.

7.Put the paper holder in position. See figure 3.

8.Install the washer and the nut that hold the paper holder.

Sanding Cuts and Sandpaper

(See chart on page 14)

Initial Cut

The purpose of the initial cut is to remove old finish and gross imperfections on the floor surface. A coarse abrasive should be used.

If glazing, loading, or burning takes place immediately into an initial cut, select a coarser abrasive. If this should occur during an initial cut, the abrasive has dulled and must be replaced.

Final Cuts

The purpose of a finishing cut is to remove the scratches produced during the initial cut. Use a fine (60-80 grit) grain abrasive.

If the surface remains rough after a finishing cut, it may be necessary to use an even finer grain of abrasive

(80-100 grit). Care should be taken in selecting the grit size of the abrasive. A very fine grain will close the pores on a wood floor making admission of a stain difficult.

Page -12 -

Clarke® American Sanders Operator's Manual - Sander 1600DC

Image 28
Contents Operators Clarke American Sanders C.A.V Operators Manual Important Safety Instructions Avertissement AdvertenciaClarke American Sanders C.A.V Operators Manual Specifications & Accessories Cords replaced by an authorized service person Grounding InstructionsExtensioncords Appliance Plug SocketHOW to Assemble the Machine Switching On The Machine C.A.VMachine Operation Picking Up Dry SubstancesMaintenance and Repair Changing The Bag Type FilterProblem Cause Action Clarke American Sanders C.A.V Operators Manual Wet/Dry Vacuum Assembly Drawing 8/02 Assembly Parts List 8/02 Description QtyClarke American Sanders C.A.V Operators Manual Product Support Branches Clarke American Sanders U. S. Warranty Highway Springdale, ArkansasSander 1600DC Manuel D’UTILISATIONContents of this Book Libro DE Instrucciones LEA Este Libro IndiceManuel D’UTILISATION Lisez CE Manuel IndexOperatorsafetyinstructions Avertissement AdvertenciaMachineintroduction Sander 1600DCInstrucciones Para LA Seguridad DEL Operador AvertissementPresentacion DE LA Maquina Nota Esta máquina es de uso comercialAvertissement Presentation DE LA Machine Avertissement PrécautionModelo Sander 1600DC Model Sander 1600DCModèle Sander 1600DC How To Install The Sandpaper Sanding Cuts and SandpaperInitial Cut Final CutsInstallation du papier abrasif Phases de ponçage et papier abrasifFases de pulimentado y tipo de papel abrasivo Fase inicialGrain Use Grano Empleo How To Install The Brush Or Pad Driver How To Adjust The HandlePreparacion DE LA Maquina Para Trabajar How to Install the Dust Control Skirt Installation de la Jupe Cómo instalar la falda120VOLTMACHINES Instrucciones Para LA Conexion Electrica DE LA Maquina Instructions Pour LE Raccordement ElectriqueHOW to Operate the Machine Mise EN Service DE LA Machine Funcionamiento DE LA MaquinaDominio DE LA Maquina Maitrise DE LA MachineMaintenance Instructions MantenimientoSander 1600DC Switches Maintenance Of The MotorMantenimiento del motor Entretien du moteurSander 1600DC Assembly Drawing 2/03 Optional Accessories Available Description Description QtyLamp Assembly Drawing 10/01 Clarke American Sanders Operators Manual Sander 1600DC Sander 1600DC Gearbox Assembly and Parts List Sander 1600DC Page Product Support Branches Highway 265 Springdale, Arkansas