Integra DTR-6.2 Level Calibration submenu, About the other settings, Press the jog dial again

Page 26

Speaker setup

Level Calibration submenu

This submenu allows you to set the volume levels of each speaker individually so that they all sound at the same level when heard from the listening position. If you are continuing from setting the speaker distances and are still in the setting mode, skip directly to step 2.

Note:

This setting cannot be made when Zone 2 is turned on, so be sure to put Zone 2 in the standby mode.

Setup

1. Press the Setup button.

If a menu other than “1. Speaker Setup” appears, turn the jog dial until “1. Speaker Setup” does appear.

2.Press the jog dial and then turn it to display the “Level Cal?”

DSP/Mode ADJ

DSP/Mode ADJ

Push To Enter

Push To Enter

3. Press the jog dial.

DSP/Mode ADJ

 

A test sound (pink noise) will be heard from

 

the left front speaker. At this point, it is not

 

necessary to adjust the volume of the test

Push To Enter

sound.

 

 

db

4. Press the jog dial again.

DSP/Mode ADJ

 

The test sound will now be heard from a

 

different speaker.

Push To Enter

 

5. Turn the jog dial to adjust the

DSP/Mode ADJ

 

volume of the test sound from this

 

speaker to the same level that you

 

heard from the previous speaker.

Push To Enter

6.Repeat the procedure in step 4 and 5 until the volume of the test sound from all speakers is the same level.

Each time you press the jog dial, the test sound will be heard

from a different speaker. The speaker order for calibration is front left → center → front right → surround right → surround left → subwoofer.

7.Press the Return button.

You return to the “Level Cal?” display.

Notes:

•If you press the Return button again, you go back up one more level.

•To exit the setting mode immediately, press the Setup button.

About the other settings

The factory settings for your DTR-6.2 are given in the table on page

12.If you connect your system in accordance with these factory settings, there is no need to change them. However, if you do not, you will need to change the settings that do not match. If you do not, signals may not be properly received resulting in poor sound or image quality, no digital output, or no output at all.

Changing a digital input setting:

1.Press the input selector button for the source that you want to change.

2.Press the Setup button.

3.Turn the jog dial to display “2. Input Setup.”

4.Press the jog dial.

“Audio Setup?” appears.

5.Press the jog dial again.

“D.Input: xxx” appears.

6.Turn the jog dial and select the connector to which the digital source is connected.

7.Press Return repeatedly or press Setup to exit the setting mode.

Changing the multichannel setting:

1.Press the input selector button for the source that you want to change.

2.Press the Setup button.

3.Turn the jog dial to display “2. Input Setup.”

4.Press the jog dial.

“Audio Setup?” appears.

5.Press the jog dial twice.

“Multich: xxx” appears.

6.Turn the jog dial to select “Yes” or “No.”

7.Press Return repeatedly or press Setup to exit the setting mode.

Changing the Component Video Input setting:

1.Press the input selector button for the source that you want to change.

2.Press the Setup button.

3.Turn the jog dial to display “2. Input Setup.”

4.Press the jog dial.

“Audio Setup?” appears.

5.Turn the jog dial to display “Video Setup?”

6.Press the jog dial.

“Cmponent: xxx” appears.

7.Turn the jog dial to select the connectors to which the source is connected (“Input 1” or “Input 2”).

8.Press Return repeatedly or press Setup to exit the setting mode.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents DTR-6.2 Important Safeguards AvisPrecautions Contents Contents 40 FM/AM random presets FM auto tuning FeaturesSupplied accessories RS 232 Control portUsing the remote controller Before using this unitInstalling the remote controller batteries Front panel display Front panel facilitiesFront panel Front panel facilities Remote controller Remote controller Connections Connecting a compact disc player CD Connecting your audio componentsConnecting a turntable Phono ConnectionsConnecting a DVD player DVD Connecting your video componentsFlow of the video signals is as follows Connecting a television monitor or projector Connecting a video cassette recorder VideoConnecting a satellite tuner or television Video Connecting settop box or video camera, etc. Video12V Trigger A, B terminals Connecting power amplifiersConnect to devices with z terminals Connect to devices with multichannel output Connecting speakersPlugging in the power cord to the AC Inlet receptacle RS 232 portConnecting the speaker cable Connecting speakersConnecting speakers Connecting a subwooferListening to music in the remote zone When using the Zone 2 Speakers terminalsWhen using the Zone 2 OUT terminals From connecting block Other componentConnecting the power Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkagePress the Setup button Speaker setupSpeaker Configuration submenu Buttons to be usedSpeaker setup Speaker Distance submenuLevel Calibration submenu About the other settingsTurn the jog dial to adjust Press the jog dial againListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Listening to Radio Broadcasts Presetting a radio station Selecting a preset radio stationErasing a preset radio station Enjoying music or videos with the DTR-6.2 Adjusting the bass and trebleListening with headphones Temporarily turning off the soundUsing the sleep time remote controller only Switching the displayAdjusting the brightness of the front display Enjoying music or videos with the DTR-6.2Adjust the tone using the Bass and Treble dials Changing the audio modeUsing the tone control Enjoying the multichannel outputUsing listening mode Listening modesUsing Cinema Re-Equalization Using listening modeChanging the listening mode Listening Mode Buttons Re-EQMenu Setup menusMain menu Sub menuSetting procedures and button operations Setup menusNavigating through the Setup menu Speaker Config sub-menu Calibrating the speaker levels Speaker Distance sub-menuLevel Calibration sub-menu Multichannel Audio Setup sub-menuDigital Input Input source signals Video Setup sub-menuListening Mode Preset sub-menu Trigger sub-menu IntelliVolume sub-menuIntelliVolume 12V Trigger aPower On Volume Volume Setup sub-menu Description listening mode parametersMaximum Volume Front EffectLate Night Setup sub-menu Headphones Level sub-menuIR in Setup sub-menu Powered Zone 2 Setup sub-menuOSD Setup sub-menu OSD Position sub-menuRecording both the audio and video RecordingRecording the input source REC OUT selector Recording a source different from that you are listening toEnjoying music in the remote zone Controlling an Integra/Onkyo cassette tape deck Using remote controllerCalling up a preset radio station Press the desired operation buttonControlling an Integra/Onkyo CD player Using remote controllerPress the CD Mode button To 9, +10 Numeric keysButton Press the DVD Mode buttonControlling an Integra/Onkyo DVD player OperationMD Mode VOL SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button Controlling an Integra/Onkyo MD recorderLearning a pre-programming code SEND/LEARN indicator Buttons thatLearning a pre-programming code Within 30 seconds, enter the 3-digit code numberLearning a pre-programming code Pre-programmong codesSAT Mode Satellite Tuner Mode Operating your programmed remote controllerDVD Mode DVD Player Mode Cable Mode Cable ModeTV Mode TV Mode Operating your programmed remote controllerVCR Mode VCR Mode Press the VCR Mode buttonTo 15 cm Programming procedureIndicator Buttons that cannot be programmedPage Press and release the same Mode button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button SEND/LEARN indicator Mode buttonsProgramming a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Running a Macro functionRunning a Direct Macro function Using a Macro functionProgramming the Direct Macro function Direct Macro Mode buttons Erasing a macro from the Mode Macro buttonPress the Mode Macro button again Erasing a direct macro from the Direct Macro buttonPress the Enter button Erasing all commands and macros that have been programmedMacro mode programming memo OperationSpecifications Amplifier SectionTroubleshooting guide If one of the messages shown below appears Troubleshooting guideVideo and Audio Onkyo U.S.A. Corporation

DTR-6.2 specifications

The Integra DTR-6.2 is a high-performance 9.2-channel AV receiver that brings a new level of audio and visual experience to your home theater. Engineered with audiophiles and home cinema enthusiasts in mind, this receiver combines advanced technology with an array of impressive features designed to elevate your entertainment setup.

One of the standout characteristics of the DTR-6.2 is its support for 8K video resolution, making it future-proof for the latest high-definition content. With HDMI 2.1 inputs, it allows for 8K60 and 4K120 pass-through, providing a seamless connection to next-generation gaming consoles and ultra-high-definition displays. It also supports HDR formats such as HDR10+, Dolby Vision, and HLG, ensuring vibrant and lifelike images.

In terms of audio performance, the Integra DTR-6.2 supports advanced sound formats, including Dolby Atmos and DTS:X. These technologies enable object-based audio, allowing sound to be placed and moved in a three-dimensional space, enhancing the immersion of your viewing experience. The receiver is also equipped with Dirac Live room correction technology, which automates the calibration of your sound setup, compensating for the acoustic characteristics of your room and delivering optimal audio fidelity.

The DTR-6.2 is powered by high-current amplifiers, capable of delivering 100 watts per channel, ensuring dynamic and powerful audio output for even the most demanding movie and music playback. The receiver offers multi-zone capabilities, allowing users to distribute audio and video signals to different areas of their home, making it a versatile choice for comprehensive home entertainment.

Streaming capabilities are abundant, with built-in support for popular platforms like Spotify, TIDAL, and Pandora. Additionally, the receiver features Bluetooth and Wi-Fi connectivity, permitting easy access to your favorite content from various devices. The Integra DTR-6.2 also integrates with smart home systems, offering seamless voice control compatibility with Amazon Alexa and Google Assistant.

With its robust construction, advanced feature set, and user-friendly interface, the Integra DTR-6.2 stands out as a premier choice for those seeking to design a sophisticated home theater system. Whether you're an avid movie watcher, a gamer, or a music lover, this AV receiver delivers exceptional audio and video quality, ensuring an immersive and engaging entertainment experience.
Top Page Image Contents