Integra DTR-6.2 instruction manual Connecting antennas, Assembling the AM loop antenna

Page 22

Connecting antennas

To use the tuner of DTR-6.2, it is necessary to prepare the supplied FM and AM antennas.

•Adjustment and placement of the FM and AM antennas for better reception must be done while listening to a station broadcast.

•If better reception cannot be obtained, then placement of an outside antenna is recommended.

Assembling the AM loop antenna

Assemble the loop antenna as shown in the illustration.

•Refer to “Connecting the AM loop antenna” below for details on connecting the loop antenna.

Insert into the hole.

Connecting the AM antenna cable

1.Press down the lever.

2.Insert the wire into the hole.

3.Release the lever.

1

2

3

Connecting the included antennas

Connecting the FM indoor antenna:

The FM indoor antenna is for indoor use only. During use, extend the antenna and move it in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion.

If the reception is not very clear with the attached FM indoor antenna, the use of an outdoor antenna is recommended.

Connecting the AM loop antenna:

The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far away as possible from the DTR-6.2, televisions, speaker cables, and power cords.

When reception is not satisfactory with the attached AM loop antenna alone, connection of an outdoor antenna is recommended.

(Indoor) AM loop antenna

FM antenna

ANTENNA

AM

FM 75

Strip away the insulation from the end of the cable, then fully insert the stripped end of the cable.

Hint:

Either of the split ends of the AM antenna can be connected to either terminal. Unlike speaker cabling, there is no polarity for AM broadcast signals.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents DTR-6.2 Important Safeguards AvisPrecautions Contents Contents 40 FM/AM random presets FM auto tuning FeaturesSupplied accessories RS 232 Control portInstalling the remote controller batteries Before using this unitUsing the remote controller Front panel Front panel facilitiesFront panel display Front panel facilities Remote controller Remote controller Connections Connecting a compact disc player CD Connecting your audio componentsConnecting a turntable Phono ConnectionsFlow of the video signals is as follows Connecting your video componentsConnecting a DVD player DVD Connecting a television monitor or projector Connecting a video cassette recorder VideoConnecting a satellite tuner or television Video Connecting settop box or video camera, etc. VideoConnect to devices with z terminals Connecting power amplifiers12V Trigger A, B terminals Connect to devices with multichannel output Connecting speakersPlugging in the power cord to the AC Inlet receptacle RS 232 portConnecting the speaker cable Connecting speakersConnecting speakers Connecting a subwooferWhen using the Zone 2 OUT terminals When using the Zone 2 Speakers terminalsListening to music in the remote zone From connecting block Other componentConnecting the power Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkagePress the Setup button Speaker setupSpeaker Configuration submenu Buttons to be usedSpeaker setup Speaker Distance submenuLevel Calibration submenu About the other settingsTurn the jog dial to adjust Press the jog dial againListening to a stereo radio station FM mode Tuning into a radio stationListening to Radio Broadcasts Erasing a preset radio station Presetting a radio station Selecting a preset radio stationListening to Radio Broadcasts Enjoying music or videos with the DTR-6.2 Adjusting the bass and trebleListening with headphones Temporarily turning off the soundUsing the sleep time remote controller only Switching the displayAdjusting the brightness of the front display Enjoying music or videos with the DTR-6.2Adjust the tone using the Bass and Treble dials Changing the audio modeUsing the tone control Enjoying the multichannel outputUsing listening mode Listening modesUsing Cinema Re-Equalization Using listening modeChanging the listening mode Listening Mode Buttons Re-EQMenu Setup menusMain menu Sub menuNavigating through the Setup menu Setup menusSetting procedures and button operations Speaker Config sub-menu Level Calibration sub-menu Speaker Distance sub-menuCalibrating the speaker levels Digital Input Audio Setup sub-menuMultichannel Listening Mode Preset sub-menu Video Setup sub-menuInput source signals Trigger sub-menu IntelliVolume sub-menuIntelliVolume 12V Trigger aPower On Volume Volume Setup sub-menu Description listening mode parametersMaximum Volume Front EffectLate Night Setup sub-menu Headphones Level sub-menuIR in Setup sub-menu Powered Zone 2 Setup sub-menuOSD Setup sub-menu OSD Position sub-menuRecording both the audio and video RecordingRecording the input source REC OUT selector Recording a source different from that you are listening toEnjoying music in the remote zone Controlling an Integra/Onkyo cassette tape deck Using remote controllerCalling up a preset radio station Press the desired operation buttonControlling an Integra/Onkyo CD player Using remote controllerPress the CD Mode button To 9, +10 Numeric keysButton Press the DVD Mode buttonControlling an Integra/Onkyo DVD player OperationMD Mode VOL SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button Controlling an Integra/Onkyo MD recorderLearning a pre-programming code SEND/LEARN indicator Buttons thatLearning a pre-programming code Within 30 seconds, enter the 3-digit code numberLearning a pre-programming code Pre-programmong codesSAT Mode Satellite Tuner Mode Operating your programmed remote controllerDVD Mode DVD Player Mode Cable Mode Cable ModeTV Mode TV Mode Operating your programmed remote controllerVCR Mode VCR Mode Press the VCR Mode buttonTo 15 cm Programming procedureIndicator Buttons that cannot be programmedPage Press and release the same Mode button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button SEND/LEARN indicator Mode buttonsProgramming a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Running a Macro functionProgramming the Direct Macro function Using a Macro functionRunning a Direct Macro function Direct Macro Mode buttons Erasing a macro from the Mode Macro buttonPress the Mode Macro button again Erasing a direct macro from the Direct Macro buttonPress the Enter button Erasing all commands and macros that have been programmedMacro mode programming memo OperationSpecifications Amplifier SectionTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Onkyo U.S.A. Corporation

DTR-6.2 specifications

The Integra DTR-6.2 is a high-performance 9.2-channel AV receiver that brings a new level of audio and visual experience to your home theater. Engineered with audiophiles and home cinema enthusiasts in mind, this receiver combines advanced technology with an array of impressive features designed to elevate your entertainment setup.

One of the standout characteristics of the DTR-6.2 is its support for 8K video resolution, making it future-proof for the latest high-definition content. With HDMI 2.1 inputs, it allows for 8K60 and 4K120 pass-through, providing a seamless connection to next-generation gaming consoles and ultra-high-definition displays. It also supports HDR formats such as HDR10+, Dolby Vision, and HLG, ensuring vibrant and lifelike images.

In terms of audio performance, the Integra DTR-6.2 supports advanced sound formats, including Dolby Atmos and DTS:X. These technologies enable object-based audio, allowing sound to be placed and moved in a three-dimensional space, enhancing the immersion of your viewing experience. The receiver is also equipped with Dirac Live room correction technology, which automates the calibration of your sound setup, compensating for the acoustic characteristics of your room and delivering optimal audio fidelity.

The DTR-6.2 is powered by high-current amplifiers, capable of delivering 100 watts per channel, ensuring dynamic and powerful audio output for even the most demanding movie and music playback. The receiver offers multi-zone capabilities, allowing users to distribute audio and video signals to different areas of their home, making it a versatile choice for comprehensive home entertainment.

Streaming capabilities are abundant, with built-in support for popular platforms like Spotify, TIDAL, and Pandora. Additionally, the receiver features Bluetooth and Wi-Fi connectivity, permitting easy access to your favorite content from various devices. The Integra DTR-6.2 also integrates with smart home systems, offering seamless voice control compatibility with Amazon Alexa and Google Assistant.

With its robust construction, advanced feature set, and user-friendly interface, the Integra DTR-6.2 stands out as a premier choice for those seeking to design a sophisticated home theater system. Whether you're an avid movie watcher, a gamer, or a music lover, this AV receiver delivers exceptional audio and video quality, ensuring an immersive and engaging entertainment experience.
Top Page Image Contents