Integra DTR-6.2 instruction manual Troubleshooting guide, Video and Audio

Page 63

Troubleshooting guide

VIDEO and AUDIO

Desired picture does not appear.

•Improper connection.

➞Check the connection again. Insert the plugs and connectors completely.

No OSD Menu display.

•Improper connection.

➞Check connections.

•OSD Menu is displayed when monitor is connected to VIDEO or S VIDEO of MONITOR OUT.

➞Confirm connections.

No sound, or sound of the selected source is not heard.

•Audio Setup sub-menu of Input Setup menu settings are incorrect.

➞ Check settings.

No picture appears on the TV screen (or monitor).

•TV (or monitor) is not set to receive the output signals from the receiver.

➞Set the TV (or monitor) to the receiver input.

•Video cable is not connected securely.

➞Check connections.

•You have connected to the COMPONENT VIDEO connectors but the DTR-6.2 is not set properly.

➞Check the Video Setup submenu of the Input Setup menu (page 38).

REMOTE CONTROLLER

Front panel controls function but remote controller controls do not.

•No batteries in remote controller.

➞Insert batteries.

•Batteries have worn out.

➞Replace batteries.

•Remote controller is not pointed at the remote sensor of the DTR-6.2.

➞Point the remote controller at the remote sensor of the DTR- 6.2.

•Remote controller is too far from the DTR-6.2.

➞Operate the remote controller within 16 feet.

•Remote controller is functioning in a different mode

➞Press the RCVR MODE button.

OTHER

LATE NIGHT function cannot be used.

•Playback source is not Dolby Digital encoded.

➞Check that the DOLBY DIGITAL indicator lights up on the display.

Re-EQ function cannot be used.

•Re-EQ is only enabled for Analog/PCM sources and Dolby Digital surround.

➞ See page 33.

Parameter cannot be set for Front Effect etc.

•Parameter may not be able to be set depending on the listening mode.

➞ See table on page 41.

Multichannel audio is not output.

•To listen to multichannel audio, “Yes” must be selected in the “Multichannel” in the Audio setup sub-menu of the Input Setup menu. Also, it is necessary to select Multichannel with the AUDIO SELECTOR button.

➞Check that the component is connected to the MULTI CHANNEL INPUT port and check the Setup menu settings.

Components in remote zone (Zone 2) do not operate properly.

•Components are incorrectly connected.

➞Check connections.

•Objects are interfering with remote controller signals.

➞Move inferring objects away from path of remote controller signals.

If one of the messages shown below appears

“Not available with headphones use”

The operation is not allowed because headphones are plugged into the DTR-6.2.

“Not available with Multichannel use”

The operation is not allowed because the selected input source is set for multichannel input.

“Not available in this Sp Config”

The operation is not allowed by the current speaker configuration.

“Not available in Zone 2 mode”

The operation is not allowed because the Zone 2 mode is turned on.

“Only available with Dolby D”

No setting other than Dolby Digital can be set.

“Not available in this Listening mode”

This operation cannot be performed in this listening mode.

“Not available with this signal”

This operation cannot be performed with this input signal.

“Powered Zone 2 is not activated”

This appears if you try to operate the DTR-6.2 in the remote zone (Zone 2) even though “Not Activated” is selected for Powered Zone 2 Setup → Powered Zone 2 in the Setup menu. To use the DTR-6.2 in the remote zone, set Powered Zone 2 to “Activated.”

“Zone 2 is Not On”

This appears if you try to operate the DTR-6.2 in the remote zone (Zone 2) even though the power is not turned on at the remote zone. Press the ZONE 2 button on the remote controller and then press the ON button.

Also refer to the respective instruction manuals of the compact disc player, DVD player, video cassette recorder, TV monitor, etc., that compose your entertainment system.

The DTR-6.2 contains an internal microcomputer that performs high-level operations. However, on extremely rare occasions, noise or interference from an external source or static electricity may cause faulty operation. If this occurs, unplug the power cord from the wall outlet, wait five or more seconds, and then plug it back in. This should correct the situation.

*To reset the surround mode and other settings to the factory default settings, hold down the Preset Memory button with the DTR-6.2 turned on and then press the Standby/On button. “CLEAR” appears in the front display and the DTR-6.2 enters the standby state.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents DTR-6.2 Avis Important SafeguardsPrecautions Contents Contents RS 232 Control port FeaturesSupplied accessories 40 FM/AM random presets FM auto tuningBefore using this unit Installing the remote controller batteriesUsing the remote controller Front panel facilities Front panelFront panel display Front panel facilities Remote controller Remote controller Connections Connections Connecting your audio componentsConnecting a turntable Phono Connecting a compact disc player CDConnecting your video components Flow of the video signals is as followsConnecting a DVD player DVD Connecting settop box or video camera, etc. Video Connecting a video cassette recorder VideoConnecting a satellite tuner or television Video Connecting a television monitor or projectorConnecting power amplifiers Connect to devices with z terminals12V Trigger A, B terminals RS 232 port Connecting speakersPlugging in the power cord to the AC Inlet receptacle Connect to devices with multichannel outputConnecting a subwoofer Connecting speakersConnecting speakers Connecting the speaker cableWhen using the Zone 2 Speakers terminals When using the Zone 2 OUT terminalsListening to music in the remote zone Other component From connecting blockConnecting the power Assembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaButtons to be used Speaker setupSpeaker Configuration submenu Press the Setup buttonSpeaker Distance submenu Speaker setupPress the jog dial again About the other settingsTurn the jog dial to adjust Level Calibration submenuTuning into a radio station Listening to a stereo radio station FM modeListening to Radio Broadcasts Presetting a radio station Selecting a preset radio station Erasing a preset radio stationListening to Radio Broadcasts Temporarily turning off the sound Adjusting the bass and trebleListening with headphones Enjoying music or videos with the DTR-6.2Enjoying music or videos with the DTR-6.2 Switching the displayAdjusting the brightness of the front display Using the sleep time remote controller onlyEnjoying the multichannel output Changing the audio modeUsing the tone control Adjust the tone using the Bass and Treble dialsListening modes Using listening modeListening Mode Buttons Re-EQ Using listening modeChanging the listening mode Using Cinema Re-EqualizationSub menu Setup menusMain menu MenuSetup menus Navigating through the Setup menuSetting procedures and button operations Speaker Config sub-menu Speaker Distance sub-menu Level Calibration sub-menuCalibrating the speaker levels Audio Setup sub-menu Digital InputMultichannel Video Setup sub-menu Listening Mode Preset sub-menuInput source signals 12V Trigger a IntelliVolume sub-menuIntelliVolume Trigger sub-menuFront Effect Volume Setup sub-menu Description listening mode parametersMaximum Volume Power On VolumePowered Zone 2 Setup sub-menu Headphones Level sub-menuIR in Setup sub-menu Late Night Setup sub-menuOSD Position sub-menu OSD Setup sub-menuRecording a source different from that you are listening to RecordingRecording the input source REC OUT selector Recording both the audio and videoEnjoying music in the remote zone Press the desired operation button Using remote controllerCalling up a preset radio station Controlling an Integra/Onkyo cassette tape deckTo 9, +10 Numeric keys Using remote controllerPress the CD Mode button Controlling an Integra/Onkyo CD playerOperation Press the DVD Mode buttonControlling an Integra/Onkyo DVD player ButtonControlling an Integra/Onkyo MD recorder SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button MD Mode VOLWithin 30 seconds, enter the 3-digit code number SEND/LEARN indicator Buttons thatLearning a pre-programming code Learning a pre-programming codePre-programmong codes Learning a pre-programming codeCable Mode Cable Mode Operating your programmed remote controllerDVD Mode DVD Player Mode SAT Mode Satellite Tuner ModePress the VCR Mode button Operating your programmed remote controllerVCR Mode VCR Mode TV Mode TV ModeButtons that cannot be programmed Programming procedureIndicator To 15 cmPage SEND/LEARN indicator Mode buttons Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againRunning a Macro function Using a Macro functionPress the Mode Macro button to complete the programming Programming a Macro functionUsing a Macro function Programming the Direct Macro functionRunning a Direct Macro function Erasing a direct macro from the Direct Macro button Erasing a macro from the Mode Macro buttonPress the Mode Macro button again Direct Macro Mode buttonsOperation Erasing all commands and macros that have been programmedMacro mode programming memo Press the Enter buttonAmplifier Section SpecificationsTroubleshooting guide Troubleshooting guide Video and AudioIf one of the messages shown below appears Onkyo U.S.A. Corporation

DTR-6.2 specifications

The Integra DTR-6.2 is a high-performance 9.2-channel AV receiver that brings a new level of audio and visual experience to your home theater. Engineered with audiophiles and home cinema enthusiasts in mind, this receiver combines advanced technology with an array of impressive features designed to elevate your entertainment setup.

One of the standout characteristics of the DTR-6.2 is its support for 8K video resolution, making it future-proof for the latest high-definition content. With HDMI 2.1 inputs, it allows for 8K60 and 4K120 pass-through, providing a seamless connection to next-generation gaming consoles and ultra-high-definition displays. It also supports HDR formats such as HDR10+, Dolby Vision, and HLG, ensuring vibrant and lifelike images.

In terms of audio performance, the Integra DTR-6.2 supports advanced sound formats, including Dolby Atmos and DTS:X. These technologies enable object-based audio, allowing sound to be placed and moved in a three-dimensional space, enhancing the immersion of your viewing experience. The receiver is also equipped with Dirac Live room correction technology, which automates the calibration of your sound setup, compensating for the acoustic characteristics of your room and delivering optimal audio fidelity.

The DTR-6.2 is powered by high-current amplifiers, capable of delivering 100 watts per channel, ensuring dynamic and powerful audio output for even the most demanding movie and music playback. The receiver offers multi-zone capabilities, allowing users to distribute audio and video signals to different areas of their home, making it a versatile choice for comprehensive home entertainment.

Streaming capabilities are abundant, with built-in support for popular platforms like Spotify, TIDAL, and Pandora. Additionally, the receiver features Bluetooth and Wi-Fi connectivity, permitting easy access to your favorite content from various devices. The Integra DTR-6.2 also integrates with smart home systems, offering seamless voice control compatibility with Amazon Alexa and Google Assistant.

With its robust construction, advanced feature set, and user-friendly interface, the Integra DTR-6.2 stands out as a premier choice for those seeking to design a sophisticated home theater system. Whether you're an avid movie watcher, a gamer, or a music lover, this AV receiver delivers exceptional audio and video quality, ensuring an immersive and engaging entertainment experience.
Top Page Image Contents