Integra DTR-6.2 instruction manual Speaker Distance sub-menu, Level Calibration sub-menu

Page 37

Setup menus

1-2. Speaker Distance sub-menu

Menu

1.Speaker Setup 1.Speaker Setup 2.Input Setup

3.Listening Mode Setup

4.Preference

 

1-.2Speaker.SpeakerConfigDistance

5.OSD Setup

 

2.Speaker Distance

3.Level Calibration

4a..BassUnitPeak Level:feet

b.Front L/R

:12ft

c.Center

:12ft

ENTER Quit:OSD

d.Surround L/R

: 7ft

ENTER Quit:OSD

Quit:SETUP

Here you will enter the distance from each speaker to your normal listening position. This is important for the timing of the acoustics to create the proper sound space that the DTR-6.2 and today’s sound systems are able to produce.

Note:

Speakers that you selected “No” or “None” for in the Speaker Config sub-menu will not appear.

a. Unit

feet: Select if you will enter the distances in feet.

meters: Select if you will enter the distances in meters.

b. Front L/R

Set the distance from the front left and right speakers to your normal listening position between 1 and 30 feet in 1-feet intervals (0.3 to 9 meters in 0.3-meter intervals).

Position the front left and right speakers so that they are the same distance from the listener. If they are not, you may lose the center position for stereo sound.

c. Center

Set the distance from the center speaker to your normal listening position between 1 and 30 feet in 1-feet intervals (0.3 to 9 meters in 0.3-meter intervals).

d. Surround L/R

Set the distance from the surround left and right speakers to your normal listening position between 1 and 30 feet in 1-feet intervals (0.3 to 9 meters in 0.3-meter intervals).

1-3. Level Calibration sub-menu

Menu

 

 

1.Speaker Setup

 

1.Speaker Setup

 

2.Input Setup

 

 

3.Listening Mode Setup

4.Preference

 

 

1-.3Speak.Levelr Calibrationonfig

5.OSD Setup

 

 

2.Speaker Distance

 

3.Level Calibration

 

4a..BassLeftPeak Level: 0dB

b.Center

:

0dB

c.Right

:

0dB

ENTER Quit:OSD

d.Surr Right

:

0dB

e.Surr Left

:

0dB

f.SubwooferENTER

Quit:OSD0dB

Quit:SETUP

Here you will set the volume for each speaker so that they are all heard by the listener at the same level. This is especially important for speaker layouts where the left and right speakers are at different distances or in asymmetrical positions due to room designs and configurations. These settings and the distance settings performed above are vital to create the proper acoustics required for the optimum sound space and dynamics.

Notes:

•The speaker level settings here are not effective for multi- channel input sources. To adjust the speaker levels for multi- channel input sources, you will need to use the CH SEL, LEVEL , and LEVEL buttons on the RC-441M remote controller. See pages 30, 31.

•This setting cannot be made when Zone 2 is turned on, so be sure to put Zone 2 in the standby mode.

Calibrating the speaker levels

(1)When this sub-menu is entered, the DTR-6.2 will emit a pink noise from the front left speaker. At this time, the Master volume automatically increases to the reference level (0dB). Remember the level of this noise and then press the cursor button. (Note that this can be adjusted to any level between – 12 and 12 decibels in 1-decibel intervals.) The DTR-6.2 will now emit the pink noise from the center speaker.

(2)Using the and cursor buttons, adjust the volume level of the noise from the center speaker so that it is the same level as the front left speaker. You can jog back and forth between the speakers to help you compare the volume levels.

(3)Press the cursor button again. The DTR-6.2 will now emit the pink noise from the front right speaker.

(4)Repeat steps (2) and (3) above for the front right and other speakers until all speakers are adjusted to the same volume level.

Note:

•Speakers that you selected “No” or “None” for in the Speaker Config sub-menu will not appear.

a.Left

Sound comes from the front left speaker. Adjust the sound level between –12 and 12 decibels in 1-decibel intervals.

b. Center

Sound comes from the center speaker. Adjust the sound level between –12 and 12 decibels in 1-decibel intervals.

c. Right

Sound comes from the front right speaker. Adjust the sound level between –12 and 12 decibels in 1-decibel intervals.

d. Surr Right

Sound comes from the surround right speaker. Adjust the sound level between –12 and 12 decibels in 1-decibel intervals.

e. Surr Left

Sound comes from the surround left speaker. Adjust the sound level between –12 and 12 decibels in 1-decibel intervals.

f. Subwoofer

Sound comes from the subwoofer. Adjust the sound level between –12 and 12 decibels in 1-decibel intervals.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents DTR-6.2 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories Features40 FM/AM random presets FM auto tuning RS 232 Control portInstalling the remote controller batteries Before using this unitUsing the remote controller Front panel Front panel facilitiesFront panel display Front panel facilities Remote controller Remote controller Connections Connecting a turntable Phono Connecting your audio componentsConnecting a compact disc player CD ConnectionsFlow of the video signals is as follows Connecting your video componentsConnecting a DVD player DVD Connecting a satellite tuner or television Video Connecting a video cassette recorder VideoConnecting a television monitor or projector Connecting settop box or video camera, etc. VideoConnect to devices with z terminals Connecting power amplifiers12V Trigger A, B terminals Plugging in the power cord to the AC Inlet receptacle Connecting speakersConnect to devices with multichannel output RS 232 portConnecting speakers Connecting speakersConnecting the speaker cable Connecting a subwooferWhen using the Zone 2 OUT terminals When using the Zone 2 Speakers terminalsListening to music in the remote zone Other component From connecting blockConnecting the power Connecting the AM antenna cable Connecting antennasConnecting the included antennas Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkageSpeaker Configuration submenu Speaker setupPress the Setup button Buttons to be usedSpeaker Distance submenu Speaker setupTurn the jog dial to adjust About the other settingsLevel Calibration submenu Press the jog dial againListening to a stereo radio station FM mode Tuning into a radio stationListening to Radio Broadcasts Erasing a preset radio station Presetting a radio station Selecting a preset radio stationListening to Radio Broadcasts Listening with headphones Adjusting the bass and trebleEnjoying music or videos with the DTR-6.2 Temporarily turning off the soundAdjusting the brightness of the front display Switching the displayUsing the sleep time remote controller only Enjoying music or videos with the DTR-6.2Using the tone control Changing the audio modeAdjust the tone using the Bass and Treble dials Enjoying the multichannel outputListening modes Using listening modeChanging the listening mode Using listening modeUsing Cinema Re-Equalization Listening Mode Buttons Re-EQMain menu Setup menusMenu Sub menuNavigating through the Setup menu Setup menusSetting procedures and button operations Speaker Config sub-menu Level Calibration sub-menu Speaker Distance sub-menuCalibrating the speaker levels Digital Input Audio Setup sub-menuMultichannel Listening Mode Preset sub-menu Video Setup sub-menuInput source signals IntelliVolume IntelliVolume sub-menuTrigger sub-menu 12V Trigger aMaximum Volume Volume Setup sub-menu Description listening mode parametersPower On Volume Front EffectIR in Setup sub-menu Headphones Level sub-menuLate Night Setup sub-menu Powered Zone 2 Setup sub-menuOSD Position sub-menu OSD Setup sub-menuRecording the input source REC OUT selector RecordingRecording both the audio and video Recording a source different from that you are listening toEnjoying music in the remote zone Calling up a preset radio station Using remote controllerControlling an Integra/Onkyo cassette tape deck Press the desired operation buttonPress the CD Mode button Using remote controllerControlling an Integra/Onkyo CD player To 9, +10 Numeric keysControlling an Integra/Onkyo DVD player Press the DVD Mode buttonButton OperationPress the MD Mode button SAT, CABLE, VCR, and TV Mode buttonsMD Mode VOL Controlling an Integra/Onkyo MD recorderLearning a pre-programming code SEND/LEARN indicator Buttons thatLearning a pre-programming code Within 30 seconds, enter the 3-digit code numberPre-programmong codes Learning a pre-programming codeDVD Mode DVD Player Mode Operating your programmed remote controllerSAT Mode Satellite Tuner Mode Cable Mode Cable ModeVCR Mode VCR Mode Operating your programmed remote controllerTV Mode TV Mode Press the VCR Mode buttonIndicator Programming procedureTo 15 cm Buttons that cannot be programmedPage Erasing all the commands programmed under a Mode button Erasing the programmed command from one buttonPress and release the same Mode button again SEND/LEARN indicator Mode buttonsPress the Mode Macro button to complete the programming Using a Macro functionProgramming a Macro function Running a Macro functionProgramming the Direct Macro function Using a Macro functionRunning a Direct Macro function Press the Mode Macro button again Erasing a macro from the Mode Macro buttonDirect Macro Mode buttons Erasing a direct macro from the Direct Macro buttonMacro mode programming memo Erasing all commands and macros that have been programmedPress the Enter button OperationAmplifier Section SpecificationsTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Onkyo U.S.A. Corporation

DTR-6.2 specifications

The Integra DTR-6.2 is a high-performance 9.2-channel AV receiver that brings a new level of audio and visual experience to your home theater. Engineered with audiophiles and home cinema enthusiasts in mind, this receiver combines advanced technology with an array of impressive features designed to elevate your entertainment setup.

One of the standout characteristics of the DTR-6.2 is its support for 8K video resolution, making it future-proof for the latest high-definition content. With HDMI 2.1 inputs, it allows for 8K60 and 4K120 pass-through, providing a seamless connection to next-generation gaming consoles and ultra-high-definition displays. It also supports HDR formats such as HDR10+, Dolby Vision, and HLG, ensuring vibrant and lifelike images.

In terms of audio performance, the Integra DTR-6.2 supports advanced sound formats, including Dolby Atmos and DTS:X. These technologies enable object-based audio, allowing sound to be placed and moved in a three-dimensional space, enhancing the immersion of your viewing experience. The receiver is also equipped with Dirac Live room correction technology, which automates the calibration of your sound setup, compensating for the acoustic characteristics of your room and delivering optimal audio fidelity.

The DTR-6.2 is powered by high-current amplifiers, capable of delivering 100 watts per channel, ensuring dynamic and powerful audio output for even the most demanding movie and music playback. The receiver offers multi-zone capabilities, allowing users to distribute audio and video signals to different areas of their home, making it a versatile choice for comprehensive home entertainment.

Streaming capabilities are abundant, with built-in support for popular platforms like Spotify, TIDAL, and Pandora. Additionally, the receiver features Bluetooth and Wi-Fi connectivity, permitting easy access to your favorite content from various devices. The Integra DTR-6.2 also integrates with smart home systems, offering seamless voice control compatibility with Amazon Alexa and Google Assistant.

With its robust construction, advanced feature set, and user-friendly interface, the Integra DTR-6.2 stands out as a premier choice for those seeking to design a sophisticated home theater system. Whether you're an avid movie watcher, a gamer, or a music lover, this AV receiver delivers exceptional audio and video quality, ensuring an immersive and engaging entertainment experience.
Top Page Image Contents